Genrad Fixtures
An I/O test interface platform, created by Pylon adopted and extended by Genrad (now Teradyne).
See Also: Board Test Fixtures
-
Product
Main Air Data Test Fixture for ADC's
TA-245
-
This is the Main Air Data Test Fixture as shown in the AZ-241 repair manuals and will allow by the book testing of the units.
-
-
Product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
-
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
-
Product
Wave Profiler Fixture
KIC® Wave Surfer™
-
The KIC Wave Surfer is a self-contained system that provides critical data on wave solder machine set up and performance. Used in conjunction with your SlimKIC 2000 and the KIC 2000 software, you can ensure your wave solder machine is set up and performing properly.
-
Product
Collins Radar Fixture with Gyro Simulator
TA-3A/B
-
This weather radar test fixture is a combination of the established WXT-250 series fixture and the RDR-2000 and RDR-2100 radars so that a single panel will provide many features that are still required today. The gyro simulator built into the panel is usable for either radar being tested and eliminate's plugging in any external simulator. The features for both product lines as shown in their respecting CMM's are provided on the panel so that full testing and alignment of these radars and their system components can be tested and/or evaluated. If you require any changes or other product versions please give us a call.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/15
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
-
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
Product
Pre-configured Power Device Analyzer / Curve Tracer (B1505A with modules and fixture)
B1505AP
-
B1505AP provides eight different pre-configured packages that satisfy a wide variety of power device measurement requirements. The package can be selected according to voltage / current range and the requirement for capacitance measurement.
-
Product
Functional Test Fixtures
-
EMC Technologies designs and manufactures discretely wired and wireless functional test fixtures used for performance verification of PCBs and Electronic Assemblies. Commercial applications have included work in support of many industries including: satellite TV, computer servers, medical, networking, and telecommunication.
-
-
Product
ARINC HSI / ADI Test Fixture
TA-2000
-
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
Product
Emergency Battery Power Supply Test Fixture
TA-61
-
This test fixture provides an interface to test and chargethe Radiant type RPS1-B Emergency Lighting power supply. The panel includes the switching required asdescribed in the CMM along with an analog currentmeter for monitoring the charging current. This panelprovides simple testing for the corporate flight departmentor DOM.
-
Product
HiFIX High Fidelity Tester Access Fixture
-
The HiFIX lineup delivers clean waveform transmission, precision docking, and multi-DUT parallel test, with high reliability.
-
Product
USB-C® – USB 2.0 Plug HS SQ Test Fixture
AUT17094
-
This product is designed for USB-C USB2.0 Receptacle Host Electrical Test.
-
Product
Test Fixture with API
TA-14VG
-
The TA-14VG test fixture is based on the requirements for the Integrated Test Procedure for the VG-14A assembly as shown in the OEM maintenance manual. The panel also contains a test point breakout for the units main connector as well as one for the VG-401 base. The VG-401 breakouts provide an in series connection that will allow easy access to the gyro's signals and also provides a way to monitor rotor current. The panel also contains a variac to allow for line voltage adjustment.
-
Product
Compression Set Fixture
ASTM D395
-
ASTM D395 Compression Set Fixture is to test rubber under constant deflection in air.
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
USB A TX Test Fixture
AUT20135
-
This newly designed AUT20135 brings enhanced user-experience with the following features:
-
Product
MIPI Test Fixtures & Software
-
The UNH-IOL has been a contributing member of the MIPI Alliance since 2007 and tests all mobile devices looking for MIPI conformance and physical layer testing including C-PHY, D-PHY, DSI, and CSI-2. All UNH-IOL MIPI Test Fixtures and Tools are available to member and non-member companies. Below are just some of the MIPI Solutions we offer. For a full list please visit our MIPI Test Fixtures page.
-
Product
MMI-A-DO, Mechanical Tandem Test Fixture
100659
-
Mechanical tandem test fixture with optimised ergonomics for function test, final test and ICT applications. The MMI dual chamber is prepared for both safety switches with guard locking and electrical interlocking. Our MMI-A-DO test fixture is versatile.
-
-
Product
Mechanical Fixture FMMA13
-
The FMMA13 is a robust mechanical fixture designed for precision testing and assembly tasks. This model from the FMMA Series offers exceptional reliability with a standard chassis housing, facilitating seamless integration into your existing systems. The fixture's manual contact generation mechanism, combined with its capability to handle up to 1700 interface signals, makes it ideal for complex setups requiring detailed testing procedures. The FMMA13 supports a customizable test system, allowing users to adapt its configuration to specific requirements, enhancing operational efficiency and accuracy.
-
Product
Bending Stiffness Test Fixture
-
Q-Card’s bending stiffness fixture features splayed feet and aggressive no-slip rubber pads for stability. It is manufactured of aerospace-grade aluminum alloy with a hard anodized, scratch-resistant, durable finish to provide years of rigorous testing and trouble-free service.
-
Product
Test Fixture
OCP NIC 3.0
-
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
Product
ESS Fixture
-
ESS - Environmental Stress Screening - is not a test. It is a product level screening process. ESS is part of manufacturing process, that verifies the operational parameters and guard bands of a product from an environmental - temperature, shock, vibration - point of view.
-
Product
Latch-on Test Fixtures
-
Latch-on Test Fixtures provide a convenient way for production personnel to quickly and reliably make electrical connections to a product for programming or final test. These custom fixtures eliminate the need to hand-wire products in order to power them up and communicate with them. Typical applications for latch-on test fixtures are metering devices, control panels, and any type of controls that connect via terminal strips.
-
Product
In‐Circuit Test Fixtures
-
Test Head Engineering designs and builds high‐quality In‐Circuit Test (ICT) Fixtures for HP / Agilent / KeySight Technologies 3070 board testers. We partner with In Circuit Test Engineering, Inc. to provide turn-key 3070 ICT solutions - both fixture and programming.
-
Product
Multi-Stage In-Circuit Test Fixtures
-
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
