Resistive Load Banks
Check power source's ability to deliver a given current and voltage at unity power factors.
See Also: Load Banks, AC Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks
-
Product
PXI 4 Banks of 40 Channel 1 Pole MUX
40-615-022-4/40/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
Radiator Mount Load Banks
-
Mosebach Manufacturing Company
Help prevent wet stacking in diesel gensets with a radiator or duct mounted load bank. Being a supplemental load, Mosebach has a solution to fit your needs.
-
Product
Insulation Resistance Measurement
MD 5060x
-
The Megabras MD-5060x is a smart, microprocessor-controlled, 5kV insulation tester and analyzer. Besides the conventional measurement of insulation resistances up to 5 TW, its advanced features allow to automatically measure both the Polarization Index and Dielectric Absorption Index, thus significantly simplifying testing of transformers.
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
Product
Resistance System Kit
PMK-151
-
The PMK-151 Basic Measurement Kit has all the functionality of the PMK-152, but adds computer downloading capabilities. It contains all the instruments you need to take a variety of resistance measurements.The PMK-151 includes Prostat's PRS-801 Resistance Set with modified 5 pound conductive rubber electrodes, the PRS-801 wide range resistance meter, and Prostat PRS-801 Connectivity software for computer data downloading. You can take measurements at 10 and 100 volts with accuracy within ±5%.
-
Product
Resistivity and Hall Effect
-
The Resistivity System allows the user to make Resistivity and Hall Effect measurements in the range of to M. Samples are mounted on special platforms inside the VTI with contacts made to the sample according to the customer's requirements.
-
Product
Portable Three Phase Phantom Load Power Source
SY2103
-
Hong Kong Songyang Industrial Ltd.
The new SY2103 series portable three phase phantom load stable power source, designed from new digital wave compound technology and according to International Standard, is newly intelligent equipment for energy meters. The equipment includes voltage/current source & standard meter, operated easily through front panel to preset directly all data of meter under test and test process.
-
-
Product
Dry Arc Resistance Tester
-
Dry Arc Resistance Tester is designed to conduct high voltage,low current Arc Resistance test on solid electrical insulation material as per:ASTM standard D495-99 (2004) and UL 746A. Why Arc Resistance Test? Many Cases of insulator failure are due to deterioration of its surface because of sustained electrical discharge or Arc. This test method is intended to test the resistance of insulating material when a high -Voltage low -current Arc close to the surface of insulation, intending to form a conducting path therein or in causing the material to become conducting due to decomposition and erosion.AdvantagesThis Test ensures that your products meet high standards of quality & safety. This product is meant for all Switchgears/ insulator/ Polymer/ electro plastic manufacturers and manufacturers who use insulators in their products e.g. Wiring Accessories, Appliances, HT/LT line insulators etc.
-
Product
Saluki SEL8 Series Programmable DC Electronic Load (up to 200KW)
-
The new SEL8 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL8 series delivers high speed and high accuracy with a resolution of 1mV and 1mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL8 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.* Customization available upon request
-
Product
1μΩ-4kΩ AC Milliohmmeter Low Resistance Tester
TH2521
-
Shenzhen Chuangxin Instruments Co., Ltd.
TH2521 AC Milliohmmeter is a high-performance and intelligent tester widely used to test contact resistance, internal resistance and battery voltage. The application of constant current source with 1kHz frequency can greatly eliminate the potential error caused by thermoelectricity on DUT. This meter has the function to automatically detect contact failures on test cable. At the range of 30mΩ, basic R resolution can reach 1μΩ. It is applicable for transformer, inductance coil copper resistance, relay contact resistance, switch, connector contact resistance, wire resistance, PCB line and via reistance dan metal defect detection, etc. In the mean time, signals, such as HIGH, LOW, PASS, can be output through HANDLER interface, thus it is very convenient to be used in automatic production line.
-
Product
AC/DC Withstanding Voltage& Resistance Tester
TH9201S
-
Changzhou Tonghui Electronic Co., Ltd.
TH9201S AC/DC withstanding voltage & insulation tester is a kind of Hipot Tester. Due to simple and compact structure, mature technique, brand new structure and operating interface, the operation becomes more convenient, and more practical functions are included as well. TH9201S can be widely applied in transformer, device, component especially for winding safety inspection.
-
Product
Pedal Force Load Cells
-
Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.
-
Product
DC Electronic Load Control Software
EES-100-xx
-
EES-100 Software controls all electronic load types. ( Single & Dual channel) data logging, constant current, constant voltage, constant power, constant resistance, up-down timing, V/I Curves, Graphing, Response Testing
-
Product
Welding Resistance Tester
WRT
-
The Welding Resistance Tester is used in battery assembly lines to detect defective intercell connections. It is equipped with a 5-channel test head for car and truck batteries. It features 1-20 O DC resistance ranges and a multi-line LC display for OCV, CCV, and DCR measurements for 5 intercell connections.
-
Product
Resistivity Meter of Powder Composites
RM-200
-
The resistivity meter is fully automated and does not required any adjustments. The measurement is made by using the four-point contact probe on the ring (ø60 x ø50 x 5mm) and rectangular prisms samples (6 x 6 x 60÷80mm). The measurement results are automatically saved in meter memory, what allows user to manage of data. The RM-200 contain series connection which allow the data transmission to PC.
-
Product
Programmable DC Electronic Load - (Economical)
63200E Series
-
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
Product
100GE Application & Security Test Load Module
CloudStorm
-
Keysight Network Applications and Security
Ixia's CloudStormTM is an industry-first 2.4 terabit application and security test solution that not only meets today’s need, but that of the future. CloudStorm delivers 3X-application and 4X-SSL-emulation scale over any other test system. It helps NEMs shortening their development cycles, and enterprises and data center operators find the right balance between mitigating security risks and delivering high end-user application performance. Emulate multi-terabit DDoS and botnet attacks to future-proof security solutions
-
Product
Battery Internal Resistance Tester
FST-7000
-
Foresight Electronics Co., Ltd.
Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds. With the help of this device either single cells / blocks or large, multi group battery banks can be measured within a short time and the precisely measured data are processed and reported by given analyzer software automatically.
-
Product
Power Quality, Ground Resistance & Insulation Testers
-
Improving energy efficiency, reducing downtime, and prolonging the life of your equipment are some of the ways you can save money with Amprobe tools.
-
Product
Resistance Grounded Systems (HRG/LRG)
-
Neutral Grounding Resistors (NGRs) are used to limit the maximum ground-fault current. Restriction of fault current lowers hazards and reduces damage done to equipment. High Resistance Grounding (HRG) systems are often used on industrial and critical power applications to maintain system uptime during a first ground fault. HRG systems are also used in tripping applications to help control touch potential on portable loads and improve personnel safety.
-
Product
Wide Range Medium Power DC Electronic Load
N6200 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N6200 series is developed based on NGI's years of experience in testing for power supply and battery. It is with high accuracy, high reliability and high cost-effective. N6200 series is with high power density and elegant appearance, which is available for benchtop use or installation in 19 inch cabinet.
-
Product
Economical Bending Beam Load Cells
EBB SERIES
-
The EBB Series is a economical low capacity bending beam load cell suitable for use in a variety of industrial and OEM force measurement and weighing applications. It is made of an aluminum alloy and comes in 1, 2, 5 and 10 kilogram ranges.
-
Product
Portable Load Cell System
-
Load Cell is designed by Seismic Source Company to measure the Hold Down weight and the output force of the Servo Hydraulic Vibrator unit. The output of the Load Cells can be recorded with any accurate seismic recording system.
-
Product
Canister Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK provides a wide range of Canister Load Cells designed for high capacity compression applications. These models offer robust construction with a capacity range beginning
-
Product
Surface Insulation Resistance Testing
-
Following over 2 years of intense research and development, we are proud to introduce the next generation of equipment used to measure changes in Surface Insulation Resistance.
-
-
Product
Resistance Tester
METRISO® 3000
-
Wolfgang Warmbier GmbH & Co. KG
Suitable for resistance point-to-point and resistance to ground measurementsIntegrated data logger with USB communication port for data transmission (50.000 test values). The supplied Report Generating Software ETC allows to generate a complete test reportA barcode scanner can be used in order to record measurement points before testing
-
Product
Digital Low Resistance Tester
TH2512
-
Shenzhen Chuangxin Instruments Co., Ltd.
The TH2512 series digital dc low resistance tester i s an intelligent, wide range, high-precision tester which suitable for transformer, inductor copper resistance, relay contact resistance, switches, connectors, wire resistance, contact resistance component solder contact resistance, PCB line, welding hole resistance and metal detection, etc. It’s applied to the production line and can use HANDLER interface and GPIB interface (option) output good/bad signal, in order to improve production line automation testing capability.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
