High Frequency
High Frequency operating at 3–30 MHz.
-
Product
XCITE 1200-2 Inertial Mass Excitation System
-
The Xcite 1200-2 Inertial Mass Excitation system provides a new dimension to structural testing. The ES-302 Exciter contains a 250 lb mass which is accelerated through a 2″ displacement by a hydraulic actuator. The 2,000 lb inertial force which is generated provides ample input to structures such as those shown below to perform low frequency seismic studies and high frequency rotating equipment analyses.
-
Product
RFID
HF (13.56 MHz)
-
BIS M uses the high frequency (HF) 13.56 MHz and supports the standard according to DIN ISO 15693 and 14443. Communication modules/gateways are used for the point-to-point or bus linking and are directly connected to a serial interface of a PC/a bus interface. The Subnet16 TM bus architecture supports a subnet of up to sixteen nodes via an RS485 interface.
-
Product
2-ch 14-bit 200 MS/s High-Speed PCI Express Digitizer
PCIe-9852
-
The ADLINK PCIe-9852 is a 2-CH 14-bit 200 MS/s digitizer for high frequency and wide dynamic range signals with an input frequency up to 90 MHz. The 90 MHz bandwidth analog input with 50Ω impedance is designed to receive ±0.2 V, ±2 V, or ±10 V high speed signals. With a PCI Express bus interface and ample onboard acquisition memory up to 1 GB, the PCIe-9852 easily manages simultaneous 2-CH data streaming. With high speed and high linearity 14-bit A/D converters and high stable onboard reference, the PCIe-9852 provides both high accuracy and high dynamic performance, making it ideal for applications requiring high-speed data acquisition, such as optical fiber and LIDAR testing, and video signal analysis.
-
Product
DC - 12 GHz High Efficiency GaAs HBT MMIC Divide by 8 Prescaler
HMMC-3028
-
The HMMC-3028 is a DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
Product
Multi Circuit Leakage Current Monitor
MCM-8000
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●The leakage current of max.8 circuits at the same time.●Easy for data management (storage by CSV formula)●Cost performance, high-speed sampling with high-frequency cut function.
-
Product
Event Based Image Sensors
EVS
-
Event-based Vision Sensors (EVS) help alleviate this issue by only sending data from pixels who have detected a change in intensity. This allows them to minimize the volume of data that is transmitted over the sensor’s data bus while minimizing the processing resources need to analyze the image. On top of this, individual pixel autonomously responds to illuminance changes allowing the sensor to detect small and/or high frequency changes with lower bandwidth requirements.
-
Product
High Frequency Multipin Coax Connectors
MDCX Series
-
Smiths Interconnect's multipin coax connectors MDCX offer low VSWR of 1.25:1 (typ) up to 10 GHz (max mated pair), maximum overall diameter of 0.125" fitted into low-profile micro-D housing, constant 50 Ohm airline impedance.
-
Product
Differential Probe
DP-60HS
-
*High Sensitivity Model: x 1, x 5, x 10 Attenuation*1 MΩ // 10PF Input Impedance*High Frequency Operation: x 1(30 MHZ), x 5(60 MHZ), x 10(60 MHz)*Especially For Low Voltage: x 1(7 Vp-p), x 5(35 Vp-p), x 10(70 Vp-p)
-
Product
Standard 3.74 (106.00) - 14.35 (407.00) High Frequency Probe
K-50B-QG-75
-
Nominal Impedance (Ohms): 50Bandwidth @ -1dB (GHz): 12.00Return Loss @ -20dB (GHz): 3.00Test Center (mil): 550Test Center (mm): 13.97Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 1,575Overall Length (mm): 40.00
-
Product
RF & Microwave Passive Components
-
SHF Communication Technologies AG
SHF’s microwave components are broadband devices suitable up to 110 GHz. Our SHF BIAS TEES are well known but perhaps a slight variation does suit your application even better. DIPLEXERS are bias tees with a certain bandwidth in the low frequency path to combine or separate high frequency and low frequency signals into or out of a single line. DC-FEEDERS are bias tees without the capacitor. Therefore, it provides slightly lower insertion loss in case it is connected to an AC-coupled device which already has a capacitor on its input. Based on our air line construction, these passive components provide resonance-free transmission over the entire operating range.
-
Product
Test Sockets
-
socket design as per customer specificationsquick + easy socket changehigh-performance spring probesdesigned for high frequency up to 16 GHz-55C/-67F to 150C/302F temperature rangemanual/automatic application optionssmall socket footprintone socket base for each insert (3x3 to 9x9 QFN)one-click switch from engineering to production socket modedevice dependent standard socket frame with changeable insertmore than 500,000 compression cyclesKelvin test applicabilitytool-free insert + actuator exchanges0.3 mm minimum lead pitchQFP extender available
-
Product
RF Cable Assemblies
-
Radiall's extensive range of RF cable assemblies features outstanding electrical performance, low loss and high frequency. The range includes flexible, semi-rigid, corrugated and hand-formable cable assemblies with a combination of RF cables and connectors optimized for each market or application. Custom RF cable assemblies are also available.
-
Product
Precision Power Analyzers
-
ZES ZIMMER Electronic Systems GmbH
Simultaneous measurement of narrow- and broadband values through innovative DualPath architectureSimultaneous capturing of fundamental frequency and broadband RMS values for instantaneous detection of losses, resp. high-frequency components
-
Product
2 GHz Dual 1:4 RF Mux, 50 Ohm Module for 34970A/34972A
34905A
-
The Keysight 34905A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation.
-
Product
Pulsed And CW ESR/EPR And DNP: Synthesizer Up To 140 GHz With Output Power Up To 30 Watt
-
Insight Product Company offers a high-power synthesizer of pulsed signals. They are ideal for ESR, EPR, and DNP experiments. The synthesizer has a high frequency stability (10-6), and allows control over the duraction and begining time of pulses. The synthesizer also enables phase manipulation, where each pulse is shifted by 90 or 180 degrees relative to the previous pulse. In contrast with the PIN modulators and injection-locked power amplifiers this synthesizer has absolutely no residual signal in the "OFF" position.
-
Product
LCR Meter, 1 MHz to 300 M/500 M/1 G/3 GHz
E4982A
-
The E4982A LCR Meter provides the best performance for the passive component manufacturing such as SMD inductors and EMI filters, where impedance testing at high frequencies (1 MHz to 300 M/500 M/1 G/3 GHz) is required. Not only for the manufacturing, the E4982A can also be utilized for R&D, quality assurance with the powerful functions such as list measurements.
-
Product
12-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-16
-
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
CFL Testing Instruments
-
CFL testing instruments of Lisun Group includes: High Frequency Fluorescent Lamp Test, Adjustable Reference Ballast, Digital Torsion Meter, Multiplex temperature tester, Lamp cap gauge, etc.
-
Product
RF Test Solutions
-
Peritec is accredited by the "RF and Wireless Specialty" (radio expertise and RF) from National Instruments (NI).The RF and Wireless Specialty, NI Alliance partners with expertise specialized design of radio frequency / wireless, authentication, automatic test, the high-frequency measurement is certified. Based on the track record and a wealth of expertise, Peritec, offers test solutions for RF / Wireless system.
-
Product
Basic Unit - Medical Equipment Functional Test Module System
GS-X
-
The GS-X Testing System consists of a Basic Unit and various plug-in test modules which the user can purchase as required. The range of functions of these Module-Box is being continuously expanded, and presently includes functions for testing the following devices: - Infusion pumps, Cardiac pacemakers, Defibrillators, High-frequency Surgical equipment, electrical safety ECG Simulation, Equipment for electro-stimulation.
-
Product
PXIe Dual Channel 20GHz 30dBm RF Amplifier
3202
-
Model TE3202 is a dual channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
Product
RF Connectors
SMPM Connectors
-
The SMPM interface is a micro-miniature interface with a frequency range of DC to 65 GHz. It is commonly used in miniaturized high frequency coaxial modules and is offered in both push-on and snap-on mating styles.
-
Product
RF Switch
-
RF switches are components used for switching the signal paths of high frequency circuits in wireless communication devices.
-
-
Product
Amplified Photodetectors
-
Hinds Instruments' photodetector modules are specifically designed for use with high frequency optical signals including those generated in Photoelastic Modulator (PEM) applications.
-
Product
Motor Tester and Analyzer
ITIG
-
The iTIG III is the industry’s most advanced electric motor tester and winding analyzer. Bringing confidence to motor repair companies, industrial end users, OEMs, and manufacturers of rotating equipment, the iTIG III features over 20 high- and low-voltage tests including high frequency surge and partial discharge.Choose multiple tests to run automatically in a sequence or select single tests. Report results with the easiest to use instrument available. Manually operate voltage dial or set up for automatic operation. Carry the iTIG III in the field or use it as a benchtop device. Connect to an external portable power pack for testing up to 40kV. The iTIG III is the most versatile and easy-to-use tester available.
-
Product
2 Piece Portables
H Model
-
H models are "2 piece" versions of the Signature ("S") Models. These compact two piece portable high frequency digital surge testers come complete with a Tektronix Type TDS1002, fully digital storage oscilloscope, 10' long test cables and a soft carrying case with a shoulder strap.
-
Product
RF Power Transistors
-
A specialized semiconductor device designed to amplify or switch high-frequency (Radio Frequency) signals, enabling powerful wireless communication in everything from cell phones and Wi-Fi to radar and satellite systems by handling significant power levels at speeds from kilohertz to gigahertz.
-
Product
DC TO 40 GHz
MDHC Series
-
Smiths Interconnect's spring loaded High Frequency Micro-D Coax Connectors MDHC offer low VSWR of 1.5:1 (typical) up to 40GHz (max mated pair), maximum overall diameter of 0.125" fitted into low-profile micro-D housing, constant 50 Ohm airline impedance.
-
Product
AC Current Shunts
CSA Series
-
Ohm-Labs’ CSA series of ac current shunts are designed as laboratory standards for ac current measurement up to high frequencies.
