PMC Adapters
Computer boards that translate the data from the PMC bus to another bus and vice versa. They are used to connect two incompatible buses. (globalspec.com)
-
Product
PCB Adapter, ITA, QuadraPaddle, 192 Position, To PCB-Mounted 6x32-Pin Ribbon Cable Headers
510151125
PCB Adapter
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 6x32-Pin Ribbon Cable Headers
-
Product
PCB Adapter, Receiver, VTAC, to (2) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) and (4) RJ45 Connectors
510170114
PCB Adapter
Mates with p/n 510171114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
Product
Adapter, 1.0 mm (f) to 1.85 mm (m), DC to 67 GHz
11921H
Coax Adapter
The Keysight 11921H precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
Product
Attenuator Interconnect Kit, 2.4 mm
11716F
Interconnect Adapter
The 11716F attenuator interconnection kit provides the necessary parts to connect 84904/8M and 84904/6L programmable step attenuators in series.
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female DIN
510140141-2
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female DIN
-
Product
Adapter, APC-7 to Type-N (f)
11524A
Contact Adapter (Receiver)
The Keysight 11524A is a general purpose grade, APC-7 to type-N female adapter.
-
Product
Coax, Contact, Receiver and ITA, 40 GHz
610102114
Contact Adapter (Receiver/ITA)
The 40 GHz Coax contact is a blind mate connector that mates with 3.5 mm and 2.92 mm connectors. It is recommended to use 2.92 mm connectors for frequencies above 35 GHz.
-
Product
PXI Pull-Thru Adapter, PCB, QuadraPaddle, 68-Pin Male VHDCI
510140125-2
Pull-Thru Adapter
PXI Pull-Thru Adapter, PCB, QuadraPaddle, 68-Pin Male VHDCI
-
Product
PCB Adapter, ITA, TriPaddle, 96 Position, To PCB-Mounted 1x96 Male DIN 41612 Connector
510108148
PCB Adapter
The 96 Pin ITA Signal Module is made from Ryton R-7, withstanding temperatures up to 220°C. Nomenclature is molded on the Module.
-
Product
NI-5781 , 40 MHz Bandwidth, RF Adapter Module for FlexRIO
781267-01
RF Adapter Module
The NI‑5781 is an analog dual-input, dual-output FlexRIO adapter module optimized for interfacing with baseband to RF upconverters and downconverters. When you pair the NI‑5781 with a PXI FPGA Module for FlexRIO, the resulting NI‑5781R is an FPGA-enabled reconfigurable I/O (RIO) baseband transceiver that you can use to implement custom RF modulation and demodulation, channel emulation, bit error rate testing, or spectral monitoring and jamming. Additionally, you can use the low latency and high throughput of FPGA‑based processing for ultra‑high‑speed control and inline processing applications.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, VHDCI ML, f/ NI PXIe-6386
510140339
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, VHDCI ML, f/ NI PXIe-6386.
-
Product
PCB Adapter, Receiver, SIM, VTAC, 34 Positions, To (6) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1)
510170103
PCB Adapter
With a fully loaded loaded SIM receiver module, this high speed solution uses all 34 positions to adapt to six (6) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) connectors. The assembly has one orderable part number and ships fully assembled.
-
Product
Coaxial Adapter, 3.5 mm (m) to 3.5 mm (f), DC to 26.5 GHz
83059C
Contact Adapter (Receiver)
The Keysight 83059C instrument-grade 3.5-mm coaxial adapter offers outstanding performance to 26.5 GHz. With SWR typically better than 1.05, this adapter is ideal for most connector saver and interconnect needs.
-
Product
Coax, Contact, ITA, 20/26 GHz, 3.5MM, w/ SMA Adapter, 90 Series Modules only
610102134
Contact Adapter (ITA)
Coax, Contact, ITA, 20/26 GHz, 3.5MM, with SMA Adapter (90 Series modules only)
-
Product
Test Port Adapter Set, 1.85 Mm To 1.85 Mm
85130H
Test Port Adapter
The Keysight 85130H test port adapter protects the test set port from being directly connected to the device under test. This adapter has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 1.85 mm to 1.85 mm male adapter and a 1.85 mm to 1.85 mm female adapter. The frequency range for these adapters is dc to 67 GHz with a return loss of 23 dB or better.
-
Product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Adapter, 1.0 mm (m) to 1.0 mm (m), DC to 110 GHz
11920A
Coax Adapter
The Keysight 11920A precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 110 GHz.
-
Product
PXI I/O Adapter For M983xA, M980xA, And P50xxA VNAs
Y1731A
Digital I/O Adapter
Access control signals of the M983xA and M980xA PXI VNAs or the P50xxA/B and P93xxB Streamline Series VNAs with twelve SMB connectors.
-
Product
cPCI and PMC Compatible Adapter Carrier
cPCIBPMC3U64ET
-
By customer request Dynamic Engineering has developed two extended temperature versions of the popular cPCIBPMC design. The design effort included switching to a new bridge to meet the temperature and timing requirements. The new bridge brings new features including the ability to operate the PMC side at a higher clock rate than the cPCI side. The new bridge also has built in features for local address spaces, using the PMC clock in monarch mode for the secondary side, and operating in transparent or non-transparent modes
-
Product
PCB Adapter, ITA, QuadraPaddle, 192 Position, To PCB-Mounted 2x68 Pin Female VHDCI Connectors
510151123
PCB Adapter
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Pin Female VHDCI Connectors
-
Product
Adapter, 1.0 mm (m) to 2.4 mm (m), DC to 50 GHz
11922A
Coax Adapter
The Keysight 11922A precision 2.4 millimeter coax in adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and a frequency range from dc to 50 GHz.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2x68 Male SCSI Connectors
510150125
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Male SCSI Connectors
-
Product
Wired Adapter for PXI, for National Instruments PXIe-8234
510109465
Pull-Thru Adapter
Wired Adapter for PXI, for National Instruments PXIe-8234
-
Product
Pull-Thru Adapter, Wired, TriPaddle, For PXI-2564
510140235
Pull-Thru Adapter
Pull-Thru Adapter, Wired, TriPaddle, for PXI-2564
-
Product
VXI Adapter Plate, Plug and Play, 2 Tier, 14U, for 9050 VXI Receiver
310113364
Adapter Plate
The VXI Plug & Play Plate allows the 9050 VXI receiver to be mounted to a chassis with the Plug & Play Flange Kit from the chassis manufacturer.
-
Product
NI-5791, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782510-01
RF Adapter Module
The NI‑5791 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5791 modules. For higher frequencies or a greater number of devices, you can use an external LO distribution amplifier.
-
Product
Sampling Scope Adapter
N5477A
Adapter Module
The N5477A sampling scope adapter makes the InfiniiMax III probing system fully compatible with the Infiniium 86100 DCA sampling scope family. With the N5477A, the DCA modules have 30 GHz of probing, increasing their performance and flexibility.
-
Product
Test Port Adapter Set, 2.4 Mm To 3.5 Mm
85130F
Test Port Adapter
The Keysight 85130F test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector designed for connecting to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. The set contains a 2.4 mm to PSC-3.5 mm male adapter and a 2.4 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 26 dB or better.
-
Product
RF Adapter Module For FlexRIO
RF Adapter Module
RF Adapter Modules for FlexRIO feature frequency coverage from 200 MHz to 4.4 GHz, with up to 200 MHz instantaneous bandwidth. When paired with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, you can program the FPGA using LabVIEW to implement custom signal processing, including modulation and demodulation, channel emulation, spectral analysis, and even closed-loop control. These modules are all based on a direct conversion architecture and feature an onboard local-oscillator which can be shared with adjacent modules for synchronization. RF adapter modules also provide digital I/O capability for interfacing with external hardware.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female
510140255
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female
