Product

High Voltage Cable/Harness Test System

CKT1175-50

-

CK Technologies, Inc.

CKT1175-50 - CK Technologies, Inc.

The CKT1175-50 is a high-voltage wiring analysis system that features a switching matrix that can be distributed around the workshop or in and around the assembly to be tested. This system is expandable in 100 or 150 test point increments to 96,000 test points, and is available with a variety of adapter cable interface connectors, with the standard being the CKT MAC interface system

Product

Universal Voltage Signaling PCI Card w/ 5 IP Slots

PCI5IP

-

Dynamic Engineering

PCI5IP - Dynamic Engineering

If you want to use IndustryPack¨ modules with your PCI system then the PCI5IP is the choice for you. The PCI5IP combines features you need with simplicity and speed. Up to 5 IP modules can be installed. 32 bit and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection. 

Product

High Voltage (Hipot) Cable Tester

CH2

-

Cirris Systems Corporation

CH2 - Cirris Systems Corporation

The easy-wire CH2 was designed for commercial, military, and aerospace applications. Running on powerful Windows-based software, the CH2 offers unrivaled testing capabilities at an unparalleled price. Compact, easy-to-use, and FAST (shorts/mis-wires detected in <1 sec for 20,000 points), the CH2 is positioned to become the ''''tester of choice'''' for high-end users.

Product

Drop Test Machine

-

Shanghai Linpin Instrument

Shanghai Linpin Instrument

Single-wing Drop Test Machine Simulate the drop conditions of packaged products when different faces, edges and corners fall to the ground from different heights, thus to understand the damage of the product and evaluate the drop height and impact resistance that the packaging materials can endure while falling down, so as to improve and optimize package design according to actual conditions of the product and national standard range.

Product

High Voltage Test Equipment

-

Yelo Ltd.

Yelo Ltd.

A hipot test is conducted by ensuring no current flows from one point to another on a circuit. A hipot test will take two conductors that should be isolated from one another and passes a high voltage between the two points. The current which flows between these points is then measured. If too much current flows, this would indicate that the points are not well isolated and the test will fail.

Product

Voltage Probes

-

Schwarzbeck Mess Elektronik

Schwarzbeck Mess Elektronik

In addition to EMI measurement with LISNs (Line Impedance Stabilisation Networks, Artificial Mains Networks), Probes are used for Terminal or Line voltage measurement.

Product

High Voltage Probe: Single-Ended

-

Tektronix, Inc.

Tektronix, Inc.

A high voltage single-ended probe is typically used for measuring ground referenced signals up to 40 kV. However, some single-ended probes are designed for oscilloscopes with isolated or floating inputs for measurements that are not ground referenced. Users should select probes with a low input capacitance specification (< 4 pF) to minimize the probe’s loading effect on the circuit because a probe with lower input capacitance will offer higher input impedance at higher frequencies.

Product

Voltage and Continuity Testers

-

Amprobe Test Tools

Amprobe Test Tools

Amprobe voltage and continuity testers have built-in shakers for fast, easy troubleshooting with CAT IV 600V/CAT III 1000V input protection. To safely detect voltages up to 122kV without contact to the current carrying conductor, choose an Amprobe high-voltage tester. These intrinsically safe tools are ideal for industrial, utility, and mine applications.

Product

Voltage, Continuity & Current Tester

T5-1000

-

Fluke Corporation

T5-1000 - Fluke Corporation

Measure current up to 100 A without breaking the circuit with OpenJaw™ design. The T5-1000 Electrical Tester is a versatile troubleshooting tool to carry to every job site. Use it to check voltage, continuity, and current–all with one compact tool.

Product

Solid State Voltage Injector

J2110A

-

PICOTEST Corp.

J2110A - PICOTEST Corp.

While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.

Product

Voltage Testers

-

Shenzhen Everbest Machinery Industry Co.,Ltd.

Shenzhen Everbest Machinery Industry Co.,Ltd.

Non-contact detection of 50 to 1000V ACRugged and double molded caseSuitable for outlets or against wire insulation testingFlashing red LED light indicatorBuilt-in bright flashlight with on/off buttonConvenient size with pocket clipAuto power offSystem self testUse on 50/60Hz circuitsComplete with two AA batteriesCATIII 1000VDimensions: 158 x 21mmWeight: 48g

Product

Auxiliary Voltage Relays

AVR

-

E-Max Instruments

AVR - E-Max Instruments

Type AVR volta acquisition systemscontrol/datage acuated relays are designed for indication alarm of annunciation in elextric utility application. the relays are used for data inputs to supervisory and sequential event recorders

Product

High Voltage SMU

-

VX Instruments GmbH

VX Instruments GmbH

Source and Measurement Units (SMUs) are devices that generate voltages or currents and can measure them simultaneously using the integrated measuring units (VMU, CMU).High-voltage SMUs work as a regulated voltage source and are able to generate very high output voltages.

Product

AC High Voltage Test Sets

-

NEO TELE-TRONIX PVT. LTD

NEO TELE-TRONIX PVT. LTD

We are highly reckoned among clients for manufacturing and exporting an excellent AC High Voltage Test Set. It is specially engineered and developed for performing varied tests on air conditioner. As to satisfy clients' requirements, we can also optimize this test set. Manufactured in accordance with industry standards using supreme grade raw materials, this AC High Voltage Test Set is offered to clients at industry leading price. Before the final dispatch in market, this test set is stringently tested on varied quality parameters.

Product

Reference Voltage Measurement Cell

C-80

-

Kharkovenergopribor Ltd.

C-80 - Kharkovenergopribor Ltd.

Cells C-80 and C-100 are used as reference devices for measuring voltage during calibration and adjustment of OLT-series testers.

Product

High-Reliability Voltage Controlled Oscillators

-

Fairview Microwave Inc.

Fairview Microwave Inc.

16 Models with Frequency Bands ranging from 10 MHz to 4350 MHz. 0.5" Hermetically Sealed Surface Mount Package. 50 Ohm Internal Matching. Designed to meet MIL-STD-883 and MIL-STD-202 Test Conditions. Wide Voltage Tuning Range from 0.5V to 20V. Phase Noise as low as -120 dBc/Hz @ 10 KHz offset. 2nd Harmonics as low as -25 dBc. RoHS and REACH Compliant. All models are EAR99. These products are used in military electronics, SATCOM, test and measurement and wireless communications.