Distribution
transmission's network array.
-
Product
Goniophotometer Test System For Led Lamp
1680A 1680B
-
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341,the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
Product
AWD Dynamometers
-
Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under "optimum" operational conditions; whereby torque is distributed to the vehicle's tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency.
-
Product
1208/9a Optical Distribution, RX/TX
-
Precise Time and Frequency, Inc.
The ptf 1208A (transmitter) and ptf 1209A (receiver) provide a convenient and simple way to transmit high quality RF signals over long distances, without the concerns associated with electrical interference and pick-up.The ptf 1208A accepts an RF input in the range from 1kHz up to greater than 10MHz and provides a combination of 8 local, high isolation, RF distribution outputs and 4 optical transmission outputs for distances up to 2 kilometers.The ptf 1209A accepts an optical input (transmitted from the ptf 1208A) and provides 12 local RF outputs, either digital (TTL into 50 ohms) or low noise sine wave signals driving 1V rms into 50 ohms (with the PLL option), or both.These systems are especially designed to accommodate IRIG B DCLS, 1PPS and other RF signals in the range from 1kHz to 20MHz.The modular construction allows for a variety of input/output configurations to provide a fully tailored application solution.
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 57651
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- One multiboard programmable beamformers- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Emergency Power Supply Units (EPSU) (24) 5-20R 0U V
EPS-2420-V60
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
3U VPX Single Board Computer
VP32002
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP32002 is a high-performance 3U VPX single-board computer, compatible with PC architecture, especially it is a China Local-design, Local-assembling product. VP32002 is an all-in-one design, supporting the 3rd generation of Intel core processors and QM77 chipset; also supports up to 16 GB onboard DDR3 memory and up to 32GB Disk-On-Modules, these features ensure its stable operation in strong shock and vibration environments. VP32002 supports a XMC interface and various I/O interface such as two SATA600 channels, two Base-BX/T GbE, two UARTs and two USB interface.The board provides a flexible PCI-Express bus interface to the backplane. The interface can be configured as follows: 1 Port x8 PCIe, 2 Ports x4 PCIe, 4 Ports x2 PCIe. This feature makes it suitable for either distributed switching system or centralized switching system.For the user to quickly form application solutions, LinkedHope provide VP32002 a complete driver package including Windows, VxWorks, Linux and QNX.
-
Product
25G Distributed Feedback Lasers
-
Macom Technology Solutions Holdings Inc.
MACOM’s Distributed Feedback (DFB) laser diodes are designed for direct modulation uncooled operation up to 25Gb/s. These products utilize patented Etched Facet Technology (EFT) for exceptional reliability with the following benefits: *Etched Facet Technology enabling high performance and product uniformity*Wide operating temperature range for wireless, PON and datacenter applications*No isolator required due to high back-reflection rejection
-
Product
cRIO-9056, 1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 75T FPGA, 8-Slot CompactRIO Controller
786426-01
Embedded Controller
1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 75T FPGA, 8-Slot CompactRIO Controller - The cRIO-9056 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers one Gigabit Ethernet port, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Industrial IoT Gateway
-
ADLINK's EMU-200 series presents users with an application-centric IIoT gateway that not only allows for quick deployment of the user environment, but also features built-in rich communication protocols and highly adaptable hardware specifications for distributed and unmanned sites with the aim to usher in a new era of efficiency and sustainability in diverse areas, including renewable energy, electric vehicle (EV) charging, building management, and factory equipment monitoring.
-
Product
Fast Response Gas Detector
Leaksurveyor
-
Teledyne Gas & Flame Detection
The GMI Leaksurveyor combines quality, ruggedness and advanced Technology in a user friendly, portable gas detector. The integral fast response and high sensitivity semiconductor sensor enables leakage surveys to be performed and distribution leaks to be quickly found.
-
Product
Multi-Wavelength Planar Lightwave Circuit Splitter (PLC Splitter)
PON-POS-3
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai multi-wavelength Planar Lightwave Circuit Splitter (PLC Splitter), is a kind of planar light-wave integrated component, and it can distribute optical power within 1260nm~1650nm wavelength that covers three wavelengths used in EPON technology (1310nm, 1490nm and 1550nm). It is especially suitable for FTTP fiber network system that switched-in by EPON ether passive optical network a nd is used as broadband passive optical splitter (POS).
-
Product
Conductor Accessories
-
AFL’s conductor accessories provide superior performance and reliability for electric power utilities and rail companies. Drawing on the experience gained from over 80 years designing and manufacturing accessory products, AFL’s conductor accessories improve the reliability of critical electrical and optical infrastructure used for the transmission and distribution of electricity.
-
Product
Matrix, Splitter and Switcher Solutions
-
Route signals from UHD and HD HDMI sources. Gefen HDMI signal distribution products create scalable and reliable AV systems using the most common standard in digital video.
-
Product
4-Ch 500 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 58651
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 500 MHz 12-bit A/Ds- Four multiband DDCs (digital downconverters)- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Two multiboard programmable beamformers- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
IRIG B Booster
-
Signals & Systems India Private Limited
IRIG B Booster – SIB-1010 is used to boost the IRIG-B AM and PWM/TTL signal which is received from the GPS unit. It provides easy and affordable connectivity to substation equipment and power generation and distribution equipment. With this Plug-N-Play unit, you can expand your IRIG B connections to multiple devices instantly. It is rugged and surge-protected equipment. Its cabinet can be mounted directly on a wall, panel or DIN Rail, without the need for additional brackets. It has an inbuilt power supply module, therefore, doing away the need for an external power adapter.
-
Product
SP-20 Spectral Photosynthetic Radiometer
-
Hangzhou Everfine Photo-E-Info Co., LTD
SP-20 test speeds up to milliseconds. It realizes the measurement functions of spectral power distribution, photosynthetic radiation parameter, optical quantum parameter, photo-electrical parameter, and it also realizes the quantity conversion between the three measurement systems. Refer to DLC, ASABE, DIN, GB, CQC, CSA and other international plant lighting standards.
-
Product
Ground Earth Resistance Tester
2678X
-
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
Product
Fluorometers
-
A fluorometer, fluorimeter or fluormeter is a device used to measure parameters of visible spectrum fluorescence: its intensity and wavelength distribution of emission spectrum after excitation by a certain spectrum of light.[1] These parameters are used to identify the presence and the amount of specific molecules in a medium.
-
Product
Logger version optical fast DO sensor
RINKO I / I D
-
Rinko I is an autonomously deployable data logger with a fast response optical DO sensor. The instrument and the software with various operating mode offer flexible observations in the field. The small-sized and the self-contained unit with batteries and a data logger can be easily integrated on platforms (e.g. CTDs). Rinko ID has a depth sensor, allowing for DO vertical distribution measurements.
-
Product
DC/DC Power Supplies
-
Astrodyne TDI’s line of DC/DC power solutions provide both a high performance and cost effective power conversion solutions for a variety of applications where efficient distributed power is required. The Astrodyne TDI team can help you find a solution that meets your specific requirements
-
Product
Mixed Gas Corrosion Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Precision Gas Dosing: Delivers exact concentrations of corrosive gases (e.g., H₂S, SO₂, Cl₂ with N₂ carrier gas; NO₂ with synthetic air) for repeatable test conditions. Supports simultaneous dosing of up to four gases, enabling multi-pollutant interaction studies.- Acrylic (PMMA) viewing window allows real-time monitoring of specimens without compromising test integrity.- Pressure monitoring system and gas sampling port ensure operator safety and compliance with industrial hygiene standards.- Advanced Environmental Control: Integrated air exchange module maintains consistent gas distribution and replicates dynamic atmospheric conditions.- Standard Compliance: Certified for IEC 60068-2-60, 60068-2-42/43, ISO 21207, and other global protocols, guaranteeing internationally recognized results.
-
Product
Photometer
DSP 10
-
Instrument Systems Optische Messtechnik GmbH
The preamplifier of the DSP 10 photometer was specially developed for fast “on-the-fly” measurements with the AMS and LGS series of goniophotometers from Instrument Systems. Spatial light distribution can be measured in a fraction of the time needed with conventional systems.
-
Product
Quality Control for more Precision in Press Hardening
PRESS-CHECK
-
The automated test system PRESS-CHECK works with two powerful high-end thermographic cameras for continuous measurement of two-dimensional temperature distribution. This measurement is carried out before the pressing operation on the surfaces of the boards to be processed and subsequently on the resulting molded parts, ultimately enabling exact compliance with the thermal process parameters.
-
Product
Split type AC Current Sensor
CTF-13NF
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Ultra compact size and high accuracy. * Easy installation in the distributing box. * Compliant with RoHS drective.
-
Product
DS18B20 TO-92 Digital Thermometer Temperature IC Sensor
604-00070
-
The DS18B20 digital thermometer is a high-resolution (9-bit to 12-bit) Celsius temperature sensor with a built-in alarm and user-programmable alarm level. The sensor uses a 1-Wire bus that requires data, power and ground. Each sensor has a unique ID, allowing them to be configured and identified on the same bus. Distributed machines, buildings, and process control are common applications. This sensor was brought into Parallax inventory for use in the P2 Quick Byte series as a demonstration device for the 1-Wire Object. This part is easily wired into a breadboard, too.
-
Product
Circuit Breaker Analyzers & Timers
CAT Standard Series
-
Circuit breakers are being tested during manufacturing, commissioning or maintenance stages. The most basic test requires timing measurement using circuit breaker timer. Their primary role is timing and motion measurement of medium and high voltage circuit breakers. Devices from CAT Standard series have suitable application in:electric power generation,distribution system,part of the electric power transmission system,contractors testing,and industrial environments.CAT Standard series meets the requirements of an easy to use circuit breaker timer and analyzer with an attractive price. Furthermore, they are portable and lightweight (weighs only up to 7 kg). Finally, the plastic case is unbreakable and has IP67 protective rating when the lid is closed.CAT Standard series includes five models:Three circuit breaker timers – CAT03, CAT31, and CAT61Two circuit breaker analyzers – CAT34 and CAT64CAT03 is a basic model intended only for timing measurement of main contact operations on the circuit breaker with one break per phase. Unlike CAT03, CAT31 has the possibility of circuit breaker operation initiation, coil current measurement, and auxiliary contact timing measurement. CAT61 differs in comparison to CAT31 by its ability to measure up to two breaks per phase.CAT34 and CAT64 are more advanced compared to CAT31 and CAT61, respectively, since they have additional analog channels. Also, they have the possibility of a travel curve recording.A user can download the test results to a USB memory stick or save it to internal memory. The CAT Standard series internal memory can store up to 500 test results (numerical and graphical data). Optional thermal printer prints test results in tabular and graphical form on 80 mm (3.15 inch) paper rolls. CAT Standard series instruments are compatible with DV-Win software. It provides full control of all CAT functions from a PC, as well as acquisition and analysis of test results.
-
Product
Thermal Imaging Camera
-
Zhejiang ULIRvisionTechnology Co., LTD
A thermal imaging camera is a device that uses infrared and thermal imaging technology to convert the image of the temperature distribution of the target object into a visible image through detecting the infrared radiation of the target object and applying signal processing and photoelectric conversion. The thermal imaging camera accurately quantifies the actual detected heat and images of the entire object in real-time in the form of a surface, thus accurately identifying the suspected fault area that is heating. The operator initially judges the fever condition and the fault location through the image color and hotspot tracking display function displayed on the screen of the thermal imaging detector, and strictly analyzes it, thereby embodying high efficiency and high accuracy in confirming the problem.
-
Product
Field Test
-
Field test equipment is an optimised solution for large system testing, which, thanks to its distributed architecture, enables the placement of several small-sized testing systems.
-
Product
Spectroradiometer
-
Designed to have a capability of producing any visible spectral distribution, mimicking various light sources in the visible region by feedback control of the radiant power emitted by individual LEDs. This LED test system will be used as a transfer standard for photometric, colorimetric and radiometric applications.
-
Product
Flatness, Bow, Warp, Curvature, Glass Thickness
1D-glass Thickness Profile Measuring Instrument GPM2
-
Optik Elektronik Gerätetechnik GmbH
Highly accurate automatic measurement of glass thickness distributions. The glass thickness profiler GPM has the function to execute a fast and precise determination of the thickness profile of flat glass samples or another transparent material with a thickness range from 30µm to 700µm (option with sensor type 1) and width to 1200mm. The measuring point distance of the profile measurement can be varied over a micro-step-controlled positioning steering between 0.1mm and 1mm. The measured value accommodation for a scanning point takes place with the help of a special hardware module for image processing algorithms within 40 ms. The entire measuring time for a sample results thus as product from the sample width which has to be measured, the measuring point distance and the measuring time per measuring point.
