Drop Testers
determine impact resilence of packaging and products. 2) in-flight test of craft carried aloft then released.
See Also: Impact Test, Pendulum Impact, Impact Hammers
-
Product
Car Accessories Material Burning Tester
ZRS-4H
-
• Test Gas Source: Gas or Liquefied Petroleum Gas (Suggestion: Use good quality gas if possible) • Burner inner diameter: ￠9.5±0.5mm, about 100mm long with air adjusting hole • Height of flame: Can be adjusted from 20 mm to 100 mm according to the standard requirement • Applying time of flame: Burning time can be adjusted from 0 to 99 minutes 99 seconds • Test process: Automatic control • Inner volume: 0.05m³ • Material: Stainless steel or iron plate spray • Power: AC 220V; 50Hz/5A
-
Product
Primary Adhesive Tester
DRK129
-
Shandong Drick Instruments Co., Ltd.
DRK129 Primary Adhesive Tester is applicable in primary adhesive tests of pressure sensitive adhesive tapes, adhesive bandage (plaster), label, protective films and other products.
-
Product
Hardness Tester
NB3010 Series
-
Newage Testing Instruments, Inc.
A basic Brinell hardness tester with semi-automatic operation. NB3010 is a cost-effective Brinell tester using deadweights with a pneumatic load system to apply and remove the loads. Operates in most all Brinell scales.
-
Product
LAN CABLE TESTER W/ Tone Generator
PA-01T
-
The LAN Cable Tester with Tone Generator is a perfect companion for any network professional. The tester can enhance one’s ability to quickly locate and verify the status of commonly used voice and data cables.
-
Product
Energized Distribution Insulator Tester
-
A sensitive voltmeter, the tester measures the difference in potential across each insulator in a suspect string. Comparative readings from satisfactory strings in the same operating situation quickly indicate the state of every insulator in the string being tested.
-
Product
Hand‐Held Digital Battery Tester with USB Port
12-1012
-
• Tests 12V Flooded, AGM and Gel Cell batteries• 4 Line LCD display• Carrying case, printing software and USB cables included• Print test results through shop PC printer
-
Product
Combination Board Tester
-
Qmax Test Technologies Pvt. Ltd.
Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
Horizontal & Vertical Combustion Tester
-
Shanghai Dean Electrical Co., Ltd
Test instrument for testing the combustion performance of plastics and non-metallic materials.Applicable to the laboratory method for determination of horizontal or vertical combustion performance of samples of plastic and non-metallic materials under 50W flame conditions.(the real object is like the picture on the right)
-
Product
High Voltage DC Personal Tester
DC/PT 75
-
Within a matter of seconds you can measure for yourself whether a voltage exceeding 750V is present. Used on voltages up to 75kV DC to earth.
-
Product
Public Switch Telephone Network Tester
295B
-
The Testphone 295B is a test telephone designed for use on Public Switched Telephone Networks (PSTN). It is designed for use on both Dual-tone Multi-frequency (DTMF - tone dialling) and Loop Disconnect (LD - pulse dialling) lines. Fitted with an integral ADSL filter, the telephone will not cause interference when connected to ADSL/Broadband lines in either `on hook` or `off hook` mode.
-
Product
Validation Testers
M Series
-
The M Series line introduces a new class of massively parallel SerDes validation testers that are ideal for high-volume data collection and characterization. Constructed using a collection of Introspect Technology’s D Series modules that are operated seamlessly using the Introspect ESP software, these massively parallel testers are able to interface to high-speed devices in their entirety.
-
Product
Leakage Current Clamp Tester with Bluetooth
M-1141XR
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Waveform display is possible with connection to a smartphone・Measurement data is to be accumulated in the server, and it is available for graph and CSV output・Auto 5-range : AC 30mA / 300mA / 3A / 30A / 300A・CT inside diameter : φ40mm・Minimum resolution : 0.01mA・Maximum value hold / Data hold function available・Band path filter with center frequency (fo = 55Hz)・Compliant with EN 61010, CAT-III 1000V / CAT-IV 600V・With backlight
-
Product
6-24V LED Heavy Duty Circuit Tester
1646
-
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12 and 24V systems. Quickly and safely test high and low voltages on all vehicle voltages, including computerized engine. High impedance to protect sensitive electronic sensors, microprocessors, electronic ignition components and air bags.
-
Product
Comparative Dissolution Tester
CD14 Comparative Dissolution Tester
-
The Teledyne LABS 14-vessel CD14 Comparative Dissolution Tester runs two methods simultaneously or independently—ideal for bioequivalence studies of generic vs. innovator drug formulations. The 14 stirring positions allow for 6+1 or 12+2 configurations for improved workload efficiency in R&D, formulations, QC, and stability-test labs. With digital temperature probes at 12 positions the CD14 comparative dissolution tester is able to test two different formulations with separate settings for every parameter under the same temperature conditions.
-
Product
Brush or Sponge Pilling Tester
TF222
-
TESTEX Testing Equipment Systems Ltd.
Brush or Sponge Pilling Tester, To determine the pilling propensity and simulate normal wear of knitted and woven fabircs used in apparel and automotive interiors by brush and/or sponging specimens together in a circular motion to form pills. Brush or Sponge Pilling Tester complies with ASTM D3511, FORD BN 12-4, FORD BN 108-03, etc.
-
Product
Signature Surge Testers
TS Model
-
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
Falling Dart Impact Tester
DRK135A
-
Shandong Drick Instruments Co., Ltd.
DRK135A Falling Dart Impact Tester is applicable in the impact result and energy measurement of the falling dart from a certain height against plastic films and sheets with thickness less than 1mm, which would result in 50% tested specimen failure.
-
Product
Single-functional testers
3110
-
The MI 3110 EurotestIM is a perfect tool for testing of permanent integrated or portable Low Voltage Electrical Installa-tions supplied by Generator or Transformer and protected by an IT earthing system. Designed for simple but efficient safety testing of Integrated IT Earthing System powered with LV Generator or Transformer! With a single, pre-programmed AUTO SEQUENCE® with sub-tests and adjustable limits it is possible to perform all the necessary verifications of safety limits of a specific LV IT installation.
-
Product
LED Lighting Panel Tester
igentic® 821t
-
Growing demand for light emitting diode (LED) products combined with increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. Sterner Automation, a leader in LED test technology, provides solutions that address these specialized requirements, including the versatile igentic® 821t panel testing system. The igentic® 821t automated process combines advanced vision technology with flexible positioning and power-up capabilities to detect inconsistencies in individual LEDs at the panel production level. The resulting detection capabilities ensure that the highest standards are met while maintaining the capacity associated with today's high speed automated lines.
-
Product
Low Temperature Retraction Tester
EKT-100TRB
-
EKT-100TRB-Low Temperature Retraction Tester is designed in accordance with ASTM D1329, ISO 2921 with fully automatic and computerized controlling system.
-
Product
P-GW Functional Tester
-
The LTE PGW Functional Tester provides a wrap-around test solution for the Packet Date Network Gateway by emulating all the LTE network elements surrounding the PDN-GW (System Under Test). The P-GW Functional Tester emulates LTE Core Network entities such as the S-GW, PCRF, OCS and OFCS. It tests the S5/S8, S7/Gx, Gy and Gz interfaces of the P-GW.
-
Product
Lead Acid Intelligent Battery Tester
612
-
This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.
-
Product
Leakage Current Tester
TOS3200
-
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment.It enables you to conduct tests that conform to the requirements of the applicable IEC, UL, JIS, and other standards, as well as the Electrical Appliance and Material Safety Law. The memory in the main unit stores the 51 types of test conditions laid down in the IEC/JIS standards for information technology equipment, household electrical appliances, audio, video electronic apparatus, luminaires, motor-operated electric tools, and electrical equipment for measurement and control and in the Electrical Appliance and Material Safety Law, thereby enabling you to conduct standard tests with simple panel operation.
-
Product
High Insulation Digital Clamp Tester
HCL-5000+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Wide AC current measurements for 0.01A～500A.・Easy operation, Push to Open and Pull to Disconnect Mechanism.・Safe AC current measurements for high voltage circuit (AC80 to 7000V).・Auto power off function and Splash proof structure.
-
Product
Datacenter 12 MPO Fiber Optic Testers & Switches
-
Optical Wavelength Laboratories
MULTI-PAIR FIBER LINKS are becoming more common than single pair fiber links for high speed communications, especially in data center environments. OWL DataCenter 12 Series test kits automatically test 12-fiber MPO cables and links without requiring cassettes or fanout cables. Higher density connections (i.e. 24, 36, 48, 60 or 72) can also be tested with MPO break-out cables.
-
Product
Power Induction Tester
MIG-ITU-K44
-
The MIG-ITU-K44 is designed for power induction testing at line frequencies of 50 and 60Hz. Power induction tests need only be performed at the frequencies of the public power supply or railway power of the country of application. Basic and enhanced level tests can be performed according to ITU-T K44.
-
Product
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AVC-50V
-
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS ).
-
Product
Peel Strength Testers
-
Peel Strength Tester can be used for peeling, stripping and other performance tests of adhesives, adhesive tapes, pressure sensitive tapes, medical adhesive bandages, protection films, release paper, laminated films, leather, woven bags and paper.
-
Product
Digital Leakage Current Tester
-
Educated Design & Development, Inc.
Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.
-
Product
Heavy Impact Tester, Battery Safety Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery impact tester tests the safety of the battery through different weights, different heights and different impact areas. After a series of tests on this battery impact tester, the battery must not have flame or explosion.
