Flaw Detectors
See Also: Flaw Detection, Ultrasonic Flaw Detectors
-
Product
Temperature Measurement IR Sensors & Detectors
M34
-
A thin-film thermopile in a TO-5 package with an active area of 3.16mm x 0.4mm that offers low noise output.
-
Product
Detector Testing
-
CI Systems' Optical Test benches are especially built to test many types of detector arrays used as the sensors of a camera, from visible to far infrared ranges. With CI Systems' expert know-how, these test benches can be tailored to a customer's design requirements. MTF, spectral response, crosstalk, NETD and sensitivity are some of the basic parameters that can be tested with CI's Optical Test benches during the design, manufacturing and integration of detector arrays.
-
Product
Disconnection Detector for PV
NSEI-100D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*This device can detect the disconnected & broken point of DC current lines between PV panels and power conditioners in PV systems, without cutting power off and without climbing the roof where PV modules are located.*Furthermore, this model can find out the disconnecting point by applying the attached detector to the specific PV module.
-
Product
Thin Film Based Thermopile Detector: 3 Channels
TM34
-
A three-channel thin-film thermopile in a TO-8 package. Each symmetrically positioned active area is 3.16mm x 0.4mm. Offers low noise output and internal aperture minimizing channel-to-channel crosstalk while increasing sensitivity.
-
Product
Porosity & Holiday Detectors
-
non-destructive testing tools used to identify pinholes, voids, and thin spots in protective coatings applied to conductive substrates (metal or concrete).
-
Product
Wall Searching Metal Detector
HHB C
-
A Wall Searching Metal Detector, also known as a stud finder or wall scanner, is a tool used to locate hidden objects behind walls, such as metal pipes, electrical wires, and wooden studs.
-
Product
Phantom Gravity Metal Detector
-
Phantom Gravity metal detector systems are designed to detect metal contamination in dry, powdery or granular free-flowing products that can be gravity fed through a pipe. Systems are available in Aluminum or Stainless Steel casings, with a selection of pipe sizes. The Diverter Valve reject system is typically used to divert contaminated product into a reject tank.
-
Product
Precipitation Detector
HD2013.3
-
Rain, snow, hail detector - Modbus-RTU or 4-20mA or 0-10V or contact output.
-
-
Product
Crack Detectors
-
GAOTek offers a large selection of crack detectors which are affordable, easy to operate and user-friendly. For some industries such as aviation, civil, infrastructure and space technology, even the slightest crack can lead to risks of hazards. There have been cases in the past where projects costing billions were destroyed in seconds due to a minute crack on the surface of the body. GAOTek provides trustworthy devices with various features that are helpful in detecting the smallest crack on an object.
-
Product
Integral Explosive-proof Intelligent Flame Detector
FSE-100
-
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
Product
SWIR Camera with InGaAs Detector
FLIR A6260
-
The FLIR A6260 SWIR camera offers superior sensitivity and dynamic range paired with the flexibility of customized windowing and integration times. This InGaAs camera is very linear in the 0.9 to 1.7 µm sensing waveband, making it the perfect tool for high temperature thermal measurements and applications that require measuring through standard glass. The A6260 offers control over settings such as integration time, while allowing you to synchronize and trigger to external events and devices.
-
Product
Temperature Measurement IR Sensors & Detectors
ST60 High Temperature
-
A single-channel silicon-based thermopile that will withstand operating temperatures of 225C, with a small active area of 0.61mm x 0.61mm in a TO-5 package. The reduced height package functions as an internal aperture. Two thermistor options provide ambient package temperature measurement. Currently only available with 8-14um silicon window. Time constant of 18ms with Nitrogen encapsulation gas delivers a very low Temperature Coefficient of Responsivity of -0.4%C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Wireless Connectivity 4 in 1 Digital Multi Detector
MS-BM68(11)B
-
Bluetooth with Memory Integrated Wireless Connectivity 4 in 1 Digital Multi Detector With Moisture Detector
-
Product
Filters / Splitters / Detectors
-
DiCon’s 100 GHz WDM is designed to multiplex and demultiplex signals in multi-wavelength systems based on the ITU 100 GHz grid. The component uses a thin film filter mounted between a pair of GRIN lens collimators. The 100 GHz WDM is housed in a compact, environmentally stable package that offers superior resistance to humidity and temperature and is suitable for mounting on a printed circuit board or within a module.
-
Product
Level Detectors
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik offers selective RF level detectors for air interface monitoring. The detectors are especially designed for frequencies used in e.g. electron accelerators. Due its mechanical design, the modules are compatible to cable route mounting systems. The detection of unintentional RF radiation is a main application field.
-
Product
Gas Leak Detectors
-
Omega's refrigerant leakage detectors perfect for maintaining air-conditioning systems with compressors and refrigerants. These units are extermely sensitive to a variety of general refrigerants.
-
Product
Portable GIS Partial Discharge Detector
JHPD-10
-
Xiamen Jiahua Electrical Technology Co.,Ltd
JHPD-10 quickly and accurately detects various kinds of partial discharge signals that occur with insulation defects in GIS. Attached on the surface of GIS the detector collects the inside discharge signal of impure gas, suspension potential and solid insulation material. The diagnostic software analyzes the fault character and locates the fault to avoid electricity accident. The device is for daily patrol inspection with high efficiency and easy operation features. Designed with two UHF signal channels, one detects the partial discharge signal; another excludes the disturbance signal like corona discharge in the air and mobile phone communication.
-
Product
Phase Failure Detectors
DSP
-
Your product The DSP-1L or DSP-1LM is used to protect your three-phase motors against phase loss, imbalance, or reversal. It continuously monitors each phase of your power supply. In case of a problem, it cuts the power to the control circuit to protect the affected motor.
-
Product
Clamp-On Open-Loop DC MicroAmmeter & Insulation Fault Detector
-
The Clamp-On Open-Loop DC MicroAmmeter & Insulation Fault Detector is a precision tool designed for detecting leakage currents in insulation systems. Featuring high sensitivity, this advanced microammeter measures direct currents as low as 1 microampere (uA) and operates within a measurement range of 10 milliampere (mA) to 10 amperes (A). Utilizing a clamp-on method with a toroidal ferro-magnetic core featuring an air gap, the device integrates AMR sensors from a differential Hall magnetometer for accurate readings. Its design is particularly suitable for large hydro generator stator windings but is also effective in various electrical applications.The device's functionality is significantly enhanced by its use of two micro-ammeters equipped with advanced signal conditioning units and a demagnetization circuit, ensuring precise data acquisition. The accompanying LabVIEW software facilitates real-time monitoring and visualization of data, allowing operators to effectively track leakage currents and identify faults within insulation systems. The dual clamp-on setup enables simultaneous measurements, providing immediate insight into potential defects without the need for cutting conductors or removing insulation, thus ensuring operator safety and system integrity.
-
Product
Non-Contact Voltage Detector
VOLTCHEK
-
The VOLTCHEK is a variable non-contact voltage detector, A proximity device which detects the presence of an alternating electric or electromagnetic field. It is used by industry professionals for live or dead voltage determination of outdoor overhead or underground at URD test points. Firstly as a proximity device to determine live or dead situations and then as a touch device to verify the source has physically reached the zero AC field. This is the only equipment capable of testing all voltage from AC 415V to 765kV from a distance, beyond arcing zone.
-
-
Product
Thin Film Based Thermopile Detector: 3 Channels, Compensated
T34 Compensated
-
A three-channel compensated (6 element) thin-film thermopile in a TO-8 package. Each active area is 3.16mm x 0.4mm. Offers thermal compensation to minimize effect of sudden ambient temperature change. Internal aperture minimizes channel-to-channel crosstalk while increasing sensitivity.
-
Product
Gas Leak Detector
-
Shanghai Yiya Electronic Instrument Co., Ltd.
High-frequency generator used for detecting leaks in a pumping system.
-
Product
SF6 Decomposition Products Detector
JH4000A-4
-
Xiamen Jiahua Electrical Technology Co.,Ltd
JH4000A-4 SF6 Electrical Equipment Decomposition Products Detector is a high precision, intelligent and portable device, able to make judgment rapidly and correctly based on the content of main decomposition products of insulation materials inside the SF6 electrical equipment like SF6 circuit breaker, instrument transformer, GIS and transformer. It detects SO2+SOF2, H2S, CO and HF. It is reliable, accurate and stable. Inspected by authorities such as the National Institute of Metrology, the device, having excellent performance, complies with relevant international and national standards. It is a product recommended for use by the State Power Grid Company. Decomposition products detection provides reliable evidence for the internal fault diagnosis and it is an effective measure for preventive and corrective maintenance.
-
Product
RF Proximity Detector
Type RPD-2 AND Type RPD-2A
-
The Type RPD-2 Radio Frequency (RF) Proximity Detector is designed to detect and locate devices that radiate radio waves in the high frequency to low microwave frequency range. Such devices often include surveillance and “spy” equipment. The Type RPD-2, when used with the different sensors, will detect the emanation of the radio wave within a confined area, and then isolate its location to within approximately a square foot. The type RPD-2A may be used as an RF field strength indicator for antenna field strength measurements. The RPD-2A is identical in function except that the meter scale is calibrated in relative dB units.
-
Product
Temperature Measurement IR Sensors & Detectors
ST60 LCC
-
A single-channel silicon-based thermopile in a LCC package for surface mount assembly in a small active area of 0.61mm x 0.61mm. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature chang
-
Product
Phantom Lumber Metal Detector
-
Ideally suited for scanning whole logs and for chipper protection, the Phantom Lumber Metal Detector is a large scale metal detection solution built rugged for the lumber industry. Lumber systems provide an effective means of detecting metal objects typically found in the application, such as fencing wire and nails.
-
Product
Safety Voltage Detector ( Rechargeable Battery Type )
350 SVD
-
Standard Electric Works Co., Ltd
● Protection class: IP65● Bright LED visual indication● Audible indication● Non-contact voltage detection: 220Vac ~ 132kVac● Wide angle voltage detection● Frequency range: 40 ~ 70Hz ● Easy-to-prove method● Self-test function● Power source: 9V rechargeable battery ● Non-contact detection by proximity● Flashlight function● Operating temperature: 0°C~50°C● Humidity: 80% RH Max● Lightweight, robust and compact● Comply with EN 61326-1
-
Product
Helium Leak Detectors
-
Agilent’s range of leak detection solutions ensure the safety, security, and consistent performance of research, vacuum, and industrial process systems. Our Helium Leak Detector (HLD), PHD-4 sniffer and C15 component leak detector are rugged, precise, and easy-to-use instruments that accurately and efficiently detect leaks in an array of industrial applications. For clean research applications, HLD configurations employ clean, dry, quiet scroll vacuum pumps. Our leak detectors feature automated start-up and calibration for maximum productivity, built in application set-ups, and an array of accessories to make any leak detection process simple.
