Concrete
See Also: Cement, Ground Penetrating Radars
-
Product
Wireless Concrete Sensor
SmartRock™
-
Tag and install the sensor on any project in just a few minutes. SmartRock is fully-embedded in the concrete, eliminating any possibility of damage occurring in harsh construction conditions after you pour.
-
Product
Concrete Testing Equipment
-
Used to measure slump, air, unit weight and temperature of fresh concrete.
-
Product
Concrete Moisture Meter
7410
-
The electrodes transmit parallel low frequency signals, calibrated to give average moisture content by comparing the change in impedance between damp and acceptably dry concrete.Calibrated ready for use on concreteInstant readings on a clear, easy to read scaleFully portable, battery operated and non-destructive
-
Product
GPR System for Concrete Inspection
StructureScan Mini XT
-
Geophysical Survey Systems, Inc.
The StructureScan Mini XT is GSSI’s newest generation of our very popular all-in-one GPR systems. The StructureScan Mini XT offers a 2.7 GHz antenna for superior target resolution and can reach depths of 20 inches (50 cm). Ideal for locating rebar, conduits, post-tension cables, voids, and real time determination of concrete slab thickness.
-
Product
Concrete Strength Testers
-
This category of products comprises the range of instruments utilized to evaluate construction material strength. The range of instruments is typically considered to be two parts. The first are non-destructive field tests of compressive strength. The second are tensile field tester systems to either determine the tensile strength of an overlay or bond material, or tensile strength of anchors embedded in the concrete. The first group is pure Non-Destructive Testing where the strength of the material is determined by correlation to another parameter more easily available and readily apparent. This is typically the hardness of the concrete or the resistance to penetration by either a pin or probe. The Windsor Probe, Windsor Pin and our line of Rebound Hammers all fall within this category. These are widely used standard tests and as such have seen use throughout the world.
-
Product
Analogue Concrete Test Hammer
181
-
The Elcometer 181 Analogue Concrete Test Hammer provides a quick, simple and inexpensive method for non-destructive evaluation of concrete compression strength and other masonry materials.
-
Product
Concrete Imaging with Ground Penetrating Radar GPR
Conquest 100
-
Conquest GPR: Get rapid, reliable results and reduce the need for destructive testing. Conquest GPR is a light, portable device that provides a fast, non-invasive method to gain accurate insights of objects below the concretesurface, even on a curved surface or column. Conquest GPR reduces risk by detecting rebar, post-tension cables, metallic and non-metallic conduits as well as current-carrying wires embedded in concrete. Once your concrete scan is complete, Conquest GPR connects to your mobile device, allowing you to email information directly from the field. Back in the office view your data and make client-ready reports in minutes.
-
Product
Concrete Surface Resistivity
Surf
-
Giatec Surf™ is a laboratory test device for rapid, easy and accurate measurement of the surface electrical resistivity of concrete based on the four-probe (Wenner-Array) technique. The Surf™ patented technology automatically measures resistivity around the concrete specimen using four channels of 4-probe array (located at 90° from each other). The PC software generates the required reports according to the standard specifications.
-
Product
Ultrasonic Concrete Testing
-
This category comprises the range of instruments that use sound or stress waves in order to determine the properties of concrete and other materials non-destructively. The first and most widely used System is our V-Meter, which utilizes the ultrasonic pulse velocity method for evaluating construction materials in the field. Transducers are available for a variety of frequencies from 24 KHz to 500 KHz. This unit has also been modified to suit the special needs of ceramics users and can be found as the Ultrapulse. The PIES, our revolutionary Portable Impact-Echo System, is an advanced instrument for non-destructive detection of flaws and defects in a variety of civil infrastructures ranging from bridges, parking structures and buildings to dams, piles, tunnels, tanks and marine structures.
-
Product
Concrete Test Hammers
-
Test hammers are used to determine the surface hardness of concrete and are one of the most widely used instruments to assess concrete compressive strength. It is the quickest, simplest and least expensive method to obtain an estimate of the quality and strength of the concrete. Test Hammers with both analogue and digital displays are available.
-
Product
Humidity and Temperature Moisture Inert and Fresh Concrete
-
Non-destructive testing / Humidity and Temperature
-
Product
Determines Presence of Carbonation on Concrete Samples
Carbo Detect System™
-
Carbo Detect is a simple colored dye field test for detecting carbonation. The single reagent is sprayed on the surface to be checked. The reagent will change to pink in uncarbonated concrete and remain colorless when sprayed on carbonated concrete.
-
Product
Concrete Moisture Testing
-
Concrete meters are used for preliminary “Wet/Dry” measurements to detect moisture pockets and assist with the optimal placement of ASTM F2170 RH test probes. It’s beneficial for quick, non-invasive surveys of the concrete slab moisture conditions before placing RH sensors.
-
Product
TDR Concrete Cure Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Concrete Cure Monitoring provides a new approach to cure monitoring in concrete and cementitious materials [1-7]. Using an ultrafast pulse and inexpensive capacitance sensor, our TDR system follows rotation of individual chemical states of water participating in the hydration reaction. The system monitors formation of bound-water hydration products, as well as unreacted free-water to form the hydrated state.
-
Product
Air and Water Permeabilityin Concrete Both At and Below the Surface
Poroscope
-
Poroscope Plus measures the time it takes for air to flow into a known volume of a sealed, evacuated chamber in the concrete. While the vacuum reduces from -55 Kpa to -50 Kpa, a measure of air permeability is determined. For water permeability, Poroscope Plus uses the same chamber filled with water, and measures the total time in seconds for a volume of 0.01 ml of water to escape.
-
Product
Rock, Concrete and Asphalt Extensometers
-
7 models cover axial, circumferential and diametral testing on aggregate material.
-
Product
Impact Echo SystemFor Field Evaluation of Concrete Structures
Vu-Con System
-
The Vu-Con Analyzer provides the engineer with the sturdiest, most reliable system for impact echo analysis. No moving parts and implementation of the latest microcomputer technology has created a system that is both sophisticated and reliable. The unit comes with a 90 mm (3.5?) by 115 mm (4.5?) graphic display screen that is easily viewed in daylight
-
Product
Strength Testing of Concrete, Brick and Mortar
Windsor Pin System
-
Measures the compressive strength of concrete, mortar and brick in-situ, quickly, accurately. A non-explosive instrument, the Windsor Pin System uses a spring-loaded device to drive a steel pin into the concrete or mortar.
-
Product
Concrete Inspection
-
Concrete structures are normally constructed using steel reinforcement and Elcometer offers Concrete Covermeters and Rebar Locators to either measure the depth of concrete over the rebar or simply to detect the rebar under the surface. Half-cell versions of the Covermeter can be used to assess the probability that corrosion is taking place on the rebar. Test Hammers are used to assess the surface hardness of cured concrete and Elcometer offers several moisture meters that can be used to determine if the structure is sufficiently dry for coating.
-
Product
Environmental Test Chambers
TTC/CTC
-
Rapid, precise and energy-saving temperature changes in the range from -42 C to +190 C, along with fast humidity recovery times, make the TTC temperature test chamber and the CTC climatic test chamber with humidity unit a perfect duo for controlled material testing, function tests, ageing tests or climate tests on composites, concrete, plastics or electronic components in material technology, the automotive and aerospace industries, and electronics.
-
Product
Adhesion Testers
-
Instruments for measuring the adhesion of coatings to metal, wood, concrete and other substrates.
-
Product
Wire Tracer
LKZ-700
-
Wire tracer LKZ-700 is designed for detecting of cables and conductors in various environments (concrete, brick, wood, ground) being under voltege, without the need to disconnect any devices from tested network, as well as in non-voltage environments.
-
Product
Cement Testing Equipment
-
High quality cement is necessary to produce concrete and mortar that meets relevant construction industry specifications. ELE international designs and manufactures a wide range of sample preparation and cement testing equipment which complies with global standards for the assessment of fineness, consistency, setting time, workability, flow, strength, soundness, heat of hydration and chemical composition.
-
Product
Moisture Meter
DL7108
-
The DL7108 enables testing of moisture levels in sawn timber, cardboard, paper, plaster, concrete and mortar.
-
Product
Rebound Hammer
Schmidt OS-120PT
-
The Schmidt OS-120 Pendulum Hammers are designed to test on softer material such as light weight concrete, gypsum boards, fresh concrete and the mortar of joints in brickwork. Their unique design allows easy to handle measurements on vertical and horizontal surfaces.
-
Product
Digital Strain-Gauge Transducer
ZET 7010 DS
-
Digital small strain gauge sensor ZET 7010-DS transducer is purposed for tensile-compression control of concrete structures, it is used in SHM (structural health monitoring systems). These transducers can be used in stationary and mobile SHM systems.
-
Product
Rebound Hammer
SilverSchmidt - STN
-
Concrete test hammer SilverSchmidt Type STN : *tandard impact energy (2.207 Nm) without PC communication*Use for concrete >10cm*Measuring range: 10-100N/mm2
-
Product
Proprietary LPWAN Wireless To Ethernet AP
WISE-4210-AP
-
Proprietary LPWAN (Sub-G) wireless technologySupport MQTT & Modbus/TCP protocolWireless to ethernet access pointLonger communication range than 2.4GHzBetter penetration through concrete and steel than 2.4GHz
-
Product
Pull Off Adhesion Tester
106
-
Applications for the Elcometer 106 Adhesion Test include paint or plasma spray on bridge decking, coatings on steel, aluminium, concrete etc.Supplied in a carry case - ideal for site testsHand operated - no need for a power supplyIncludes a cutter for EN13144 and ISO 4624 tests
-
Product
Non-Destructive Tests
-
Non-destructive tests on reinforced concrete and masonry structures are the first method of investigation for verifying the real conditions of a building or structure, existing or under construction. As indicated by the anti-seismic legislation, these tests can be performed by all authorized operators.
