Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
product
4-Pin Power D-Type Cable, Female to Female, 1m
40-970-404-1m-FF
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
SIMRC - RS232 to I2C Converter PCB
1080-001
Pickering Interfaces Series 1000 SIM Reed Relay Cards offer a choice of switching configurations using low cost industry standard SIM connectors. They are ideal for placing switching systems in fixtures close to the unit under test.
-
product
LXI Microwave Multiplexer, SP4T, 4-Bank, 50GHz, 50Ω, SMA-2.4
60-803-604
Our 60-803-604 is a 4 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Indirect Sequential Injection
The ECU is designed to exploit the chemical-physical characteristics of the gas fuel used in Otto engines while maintaining the level of emissions of the exhaust gas according to the original standard car.The connector used in Air 48 is automotive type 48- Poles . The connection to the engine signals , offers exceptional qualities of connective security and protection against water infiltration .
-
product
PCI Expansion Card
4624-3
VECTOR Electronics and Technology, Inc.
120 contacts (60 each side) on 0.050" centers. Overall GND plane, Pad-Per-Hole, Peripheral Buses. Isolated pads around each hole. 32-bit ISA format. Universal tab fits both 3.3V and 5V tab notch patterns. Mounting bracket included.Peripheral buses for voltage and ground distribution.I/O mounting area for D-sub and ribbon cable connectors.
-
product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
3.5 Inch SBC with 7th Gen Core i7 CPU and PCIe/104
VENUS
Based on the “Kaby Lake” 7th generation Core i7 processor, Venus offers high CPU performance in a small form factor rugged SBC with modest power consumption. It incorporates a full suite of rugged features such as soldered memory, latching connectors, a thicker PCB, and true -40/+85ºC operating temperature, making it suitable for the most demanding vehicle applications. High I/O density, multiple expansion sockets, rugged design, modest power consumption of 14W, and wide temperature operation combine to make Venus an extremely attractive option for applications requiring high CPU performance or ruggedness.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 4-Bank 40GHz SMA-2.9
60-801-404
The 60-801-404 is a 6-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber
40-850A-114-M50-HI
The 40/42-850A-114-M50-HI is a PXI/PXIe 4-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
RMC
Receive Multicoupler (Rx AIT)
*Provides a common receive distribution point for multiple basestations*Each Cellular and PCS unit supplies 8 ports and supports 2 channels*The single 1U tray includes integrated Bias- T and test ports*QMA receive connectors provide quick and sure connections
-
product
PXI Single 24:1 High Voltage Power MUX
40-331-001
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
product
Compact Reflow Checker
RCP-200
Unprecedented miniature size, high precision, stable, and well-reproducible temperature control of reflow furnace. Proprietary "Heat Resistant Micro Connector" makes it possible to measure at 6 points.
-
product
Cable Assembly, Receiver, QuadraPaddle, 20", 2 NI SH96F-96M-RES 96
540256010140
Cable Assembly, Receiver, QuadraPaddle, 20", 2 NI SH96F-96M-RES 96 pin connectors with resistors
-
product
PCIe FPGA Carrier For FMC+, Altera Arria-10 GX1150
PCI536
The PCI536 is based on the Altera Arria-10™ GX1150 FPGA in F1517 package. The FPGA interfaces directly to the FMC+ DP 0-23 (single connector) and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. The PCI536 has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. It also has interface to two DDR4, 64-bit wide, with 16 GB total memory. This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
product
Cable 96-Pin Micro-D Female to Unterminated, Cut Ends, 0.5m
40-972B-096-0.5m-FU
The 96-Pin SCSI Style Micro-D to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
product
MP CI set
The MP CI set up to measure coupling impedance is used to determine EMC characteristics of connectors and cables. The coupling inductivity defines the coupling inductance of external disturbance on the shield or on the ground with the desired signals. If the coupling inductivity is considered in the construction set-up and the pin or wire assignment of connectors or cables, then the connectors or cables will be more interference-resistant. The MP CI set-up for measuring coupling impedance can be used for following measurements at connectors or cables: 1. measurement of a single signal (common mode) 2. measurement of a symmetrical signal (common mode) 3. measurement of a symmetrical signal (differential mode)
-
product
LXI Microwave Multiplexer, SP6T, 10-Bank, 26.5GHz, 50Ω, SMA
60-800-310
Our 60-800-310 is a 10 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Multi-Mode, 62.5/125 Fiber, SC Connectors
40-855A-222-M
The 40/42-855A-222-M is a PXI/PXIe dual 2-channel multiplexer with SC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
20-Pin Scorpion Cable, Female to Unterminated, Cut Ends, 30A, 2m
A020AFR-C-3A200
This is a 2m long female to unterminated 20-Pin Scorpion cable assembly with cut ends constructed from 37/0.4 (10AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 50 GHz, 50 Ω, SMA-2.4, External Termination, Failsafe, Remote Mount
40-781A-722-E
The 40-781A-722-E (PXI) and 42-781A-722-E (PXIe) are dual failsafe SPDT 50 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
780927-02
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 1m
40-972-068-1m-MU
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
2-slot IndustryPack Carrier
CPCI-100A-BP
The CPCI-100A-BP 2-slot IndustryPack carrier for 3U CPCI is available with back-panel I/O via the CPCI J2 connector. The carrier provides an 8 MHz IndustryPack clock for each slot. The standard 8 MB memory space is available for each IndustryPack site.
-
product
6U CompactPCI Rear Transition Module With Rich I/O Interfaces, CPCI-R6002 Series
20040264
The cPCI-R6002 Series is a 6U CompactPCI rear transition module (RTM) in single/dual slot width (4/8HP) form factor featuring rich IO interfaces. [END OF LIFE} The single slot cPCI-R6002 supports 2x GbE, 2x USB 2.0, 1x DB-9 COM, and 1x DVI-I on the rear panel. The dual slot cPCI-R6002D supports 2x GbE, 4x USB 2.0, 1x DB-9 COM, 1xDVI-I, PS/2 KB/MS, and audio ports on the rear panel. For storage, the cPCI-R6002 provides 2x 7-pin SATA connectors and the cPCI-R6002D offers an additional 2.5" SATA drive space via daughter board. Onboard IO includes 1x 5-pin USB pin header and 1x 10-pin serial TX/RX pin header.
-
product
Fanless Embedded System With Intel® Celeron® J1900, HDMI, VGA, 2 GbE LAN, 4 USB, 3 COM And 10 To 34 VDC
eBOX626-842-FL
The eBOX626-842-FL is the energy-efficient fanless embedded box PC suited for rugged and extreme applications with its extended temperature and wide range voltage capability. The extreme compact box PC utilizes an onboard Intel® Celeron® quad core processor J1900 2.0GHz (codename: Bay Trail-D) to boast both excellent performance and ultra-low power consumption. The ultra-slim fanless embedded computer supports system memory up to 8 GB with one DDR3L-1066/1333 SO-DIMM socket and offers HDMI and VGA display outputs, offering not only high computing capability but also excellent graphics performance. Integrated single-chip design, the brand new ruggedized embedded system is lighter and thinner compared to previous eBOX620 series. Supporting wide operating temperature between -20°C to +55°C and 10 to 34VDC wide DC input voltage, the fanless embedded PC is excellence for wide range of industrial applications. Its passive cooling design also offers quiet, fanless operation with low power consumption, and all at an attractive price point. With full-featured of I/O interfaces, the Intel® Celeron®-based eBOX626-842-FL supports two RS-232/422/485 ports, one RS-232 port, VGA, HDMI, audio, dual Gigabit Ethernet LAN ports, four high-speed USB 2.0, three SMA type connector openings for antenna, 10-34VDC power input connector, and one ATX power switch. One 2.5" SATA HDD drive bay and mSATA are also embedded in the embedded computer to possess sufficient storage.
-
product
Cable Assy 9-Pin D-Type, M/M, 2m
40-970-009-2m-MM
A 9 Pin Cable Assembly suitable for general use and constructed from PFA insulated wire. The connector assembly can be sured to the product by screwlocks.
-
product
Cable Assy 25-Pin D-Type M/M 2m
40-970-025-2m-MM
The 25-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 25-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
PXI 75 x Normally Closed Relay 1A 60W
40-145-101-NC
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
product
8-Pin Power D-Type Cable, Female to Unterminated, Tinned Ends
A008PF4-T-5A200
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
product
Cable
RCONQPMC-4
RCONQPMC-4 - Transitions from a SCSI-68 pin connector to eight CJ70 Twinax, 3 lug, 1553 cable jack ends and one D-Sub 50 pin connector for additional I/O.
