Bus Interfaces
Enable bus interoperability.
See Also: Interfaces, Serial Interfaces, Parallel Interface, UI, MIPI, Interface Adapters, Bus
-
product
Introduction to Graphical User Interface - Softpanel
61800 Series
The increased demand for Distributed Energy Resource (DR) products such as PV Inverter and Wind Energy systems, have increased the demand for regulation test standards to insure proper operation and safety of on-grid products. Manufacturers testing to prove compliance, need test equipment that can simulate and measure and test their products. Chroma’s 61800 family of Regenerative Grid Simulators provide a full 4 quadrant, regenerative, grid simulation for compliance, safety, and product verification testing
-
product
Interface
RCNIC-A2PA
The RCNIC platform is a high performance PMC module for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
product
Interface Board, 16:1 USB
40-965-909
Converter card for 40-737-001 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 16 USB type A and 1 USB type B connectors. Allows the multiplexing of up to 16 USB1 or USB2 signals.
-
product
Interface Board for Gigabit Ethernet
40-965-910
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
product
ARINC PCI Express One Lane Interface Card
PCIE1L-A429
The ARINC PCIE1L-A429 Interface Card and AltaAPI Support Software Represent the Latest ARINC 32-bit FPGA Protocol Engine Technology. Encode and Decode almost Any ARINC-429 PHY Level Label/Word Signal. The First Card in the Industry to Offer Advanced Test Functions of Signal Generation and A/D Signal Capture. The one lane card PCIe is the industry first low profile
-
product
1553 to Ethernet Converter
ENET2-1553
eNet2-1553™ is an innovative product that provides “remoting” of 1553 operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). eNet2-1553 is a small, low-power, rugged device that provides real-time Ethernet connectivity to for two dual redundant 1553 (A/B) busses. Ideal for remoting 1553 connections for in-field applications or point-point lab usage.
-
product
Mini PCI Express Interface Card
MPCIE-1553
The MPCIE-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for MIL-STD-1553 networks. Coupled with AltaAPI Represents the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software - in an amazingly small package.
-
product
MIL-STD-1553 Module
QPM-1553
The QPM-1553 provides the highest level of performance, flexibility and interface density for MIL-STD-1553A/B on a PMC (PCI Mezzanine Card) module. The QPM-1553 is integrated with powerful software that reduces development time. All 1553 databus functionality is supported from our advanced API (Application Programming Interface).
-
product
RF Switching Interface Units (RFIU)
LXI, GPIB, and USB RF Interface Units (RFIU) available off-the-shelf or customized for you.
-
product
FlexRay Interface Device
FlexRay Interface Devices provide two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. FlexRay Interface Devices work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
10-Ch Pneumatics CAN without RCV module
YAV90PNF
This pneumatic subsystem is the same as YAV90PNE, but without the VPC receiver module integrated, making it a good option to be used inside the fixture. Since the control is CAN, user can easily place electrovalves inside the fixture without the need to use a bunch of wires.
-
product
IVN-8561, Automotive Ethernet Interface Device
786169-01
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
product
MIL-STD-1553 & ARINC PMC Interface Card. Supports cPCI/PXI Backplanes
CPCIC3/6-MA4
Alta Data Technologies’ CPCIC3/6-MA4 (PXI Compatible) interface module is a multi-channel, multi-protocol 1553 and ARINC PMC on 3U (PXI Compatible) or 6U carrier card supported by the latest software technologies. This hardware and software package provides increased system performance and reduces integration time.
-
product
PXI-8516, 2-Port PXI LIN Interface Module
781366-01
2-Port PXI LIN Interface Module—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver.The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
product
sbRIO-9860, Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module
787325-01
Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.
-
product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-4x10G SFP+
- Support up to four 10GbE SFP+ interfaces- COM.0 R3.1 Type 7 compliant- Dedicated for Express-ID7
-
product
NI-9870, 4-Port, RS232 C Series Serial Interface Module
779891-03
The NI‑9870 adds RS232 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
product
High Performance PCIe-GPIB Interface Card
82351B
Convert your PCI computer directly into an intrumentation control; install easily with plug-and-play configuration.
-
product
4x IDC to 192 Pin Quadrapaddle
YAV90Q04
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
product
Interface Board for Conduction Cooled PCI Mezzanine Card Systems
EXC-708ccPMC
The EXC-708ccPMC is an ARINC-708 /453 interface board for conduction cooled PCI Mezzanine Card systems. The board supports two or four ARINC-708 /453 channels. Each of the channels can be programmed either as transmit or receive. Each channel implements an 8K×16 FIFO and supports polling and / or interrupt driven operation.The EXC-708ccPMC comes complete with C-driver software library including the source code.
-
product
3 Function Slot MOSA Nano Aircraft Interface Computer (AIC)
NIU3A-AIC-01
NIU3A-AIC-01 is a Modular Open Systems Approach (MOSA) Aircraft Interface Computer with low power high performance ARM Cortex -A53 processing. 8 GB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet.
-
product
MIL-STD-1553 PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-1553 and ECD54-1553
Alta Data Technologies’ PCCD-1553 & ECD54-1553 interface modules are a multi-channel (1-2) 1553 card supported by the latest software technologies. The cards are based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
Multi-Channel, Multi-Protocol 1553 and ARINC 1/2 Size PCIe 4-Lane Interface Card
PCIEC4L-MA4
Alta Data Technologies’ PCIEC4L-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC ½ size PCI Express 4 Lane interface card (PMC on 4 Lane PCI Express Carrier) is supported by the latest software technologies. The PCIEC4L card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
Ethernet to CAN Bus Gateway
YAV90090
• High-performance Arm Cortex-M3 MCU with 512 Kbytes Flash, 120 MHz CPU, ART Accelerator, Ethernet P/N STM32F207IEH6• USB 2.0 connector for serial data transfer (reserved for factory use)• Connections for CAN, and power supply via 4-pole Weidmüller connector• Reboot and reset of the device to factory defaults with a reset button• Plastic casing for benchtop operation• LEDs for device status and power supply• Voltage supply from 8 to 30 V
-
product
Interface
RCEI-830A-TB
Designed for embedded, laboratory and simulator applications, the RCEI-830A-TB supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, receive message time-tagging and error detection, and IRIG-B receiver (AM or DC/TTL) and generator (DC/TTL).
-
product
PXI-8513 , 2-Port, Software-Selectable PXI CAN Interface Module
780688-02
2-Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
PCI-8531, 1-Port, CANopen Interface Device
781060-01
The PCI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. CANopen was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The PCI‑8531 can transmit or receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. It also features a batch SDO editor with EDS file integration and LSS services support for slave node configuration.
-
product
PXIe-8245, 4-Port, 10/100/1000BASE-T PXI Ethernet Interface Module
787313-01
The PXIe-8245 supports Ethernet-based communication between PXI hardware and external instruments and devices. This PXI Ethernet Interface Module includes four RJ45 10/100/1000BASE-T Ethernet interface ports in a single-slot PXI Express module.
-
product
PCIe-8244, 4-Port, USB3 Vision Frame Grabber Device
782890-01
The PCIe‑8244 is a USB 3.0 interface device designed for use with USB3 Vision cameras. USB 3.0 is ideal for high-data-rate machine vision applications. USB3 Vision cameras also offer plug‑and‑play functionality and ease of use through a standardized catalog of functions.
