Filter Results By:
Products
Applications
Manufacturers
-
product
32-CH Discrete Output Daughter Board Module
HSL-DO32-DB-N
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type outputs*Photo couple isolation voltage: 2500Vrms*Output switching capacity: Single channel 500mA; all channels 60mA at 24VDC*Output response time:ON OFF: 180µs, OFF ON: *1.2µsTerminal Base:HSL-TB64 or HSL-TB32U-DIN
-
product
32-CH Discrete Input Daughter Board Module
HSL-DI32-DB-N
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type sensor inputs or dry contact*Photo couple isolation voltage: 2500Vrms*Input impedance: 4.7KΩ*Input current: ??10mA (Max), ??12.5mA (Peak)*Input voltage: ??40V (Max)
-
product
AT Command Master+Slave / Central+Peripheral
AT command module serie
Raytac's AT command module series comes with AT command firmware pre-programmed which helps developers enjoy a Design Saving & Time-To-Market journey.
-
product
Programmable Modbus Simulator
ModMultiSim
ModMultiSim is a programmable Modbus simulator that enables realistic simulation of multiple Modbus slaves in their environment. Connect your Modbus masters to ModMultiSim, instead of real Modbus slave devices, in order to test and configure the masters.
-
product
High Performance 335 M, 6 Channel Digital Receiver
DP-VME-5838
The DP- VME-5838 is a VME64x slave, high performance 335M, six channel Digital receiver card. It samples and down converts the analog IF signals into the digital base band data. The processed I/Q data are pulse compressed and decimated to the base band rate. In the Central Unit system, this pulse compressed I/Q data has to be sent to the signal processing unit through a 2.5G speed Optical SFPDP link.
-
product
Modbus Master Data Scanner
ModScan
ModScan is a Windows application which operates as a modbus master. It allows you to access and change data points in a connected slave device using either the RTU or ASCII Transmission mode. ModScan is ideally suited for quick and easy compliance testing of the modbus protocol and its built-in display of serial traffic allows effective troubleshooting of field connections.
-
product
Wire Harness Tester
Panther4HT Master- Slave DSU
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
product
PXI 25 x DPST Electromechanical Relays
40-146-002
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
Slave Dual Industry Pack Carrier
CPCI-SIP-3
The new CPCI-SIP-3Module provides a 3U high performance flexible I/Oscheme, that supports industry standard IndustryPacks. Choose from over a 100 different IndustryPacks from Alphi Tech and others. For applicationrequiring low cost, high density I/O or unique combinations, the CPCISIP-3 is the perfectsolution.
-
product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
product
PTP Toolbox
OSA 5410/11
The OSA 5410 Series is a family of compact and cost-effective synchronization distribution and assurance devices that bring the power of Syncjack™ to any network. Following a toolbox approach, the family members of the OSA 5410 Series can be utilized in a variety of network synchronization applications including IEEE 1588v2 Access Grandmaster, Boundary and Slave Clock, GNSS receiver and Primary Reference Time Clock (PRTC), synchronization signal conversion and sync probe applications.
-
product
Modbus Diagnostic Program
Modsak
Modsak is a versatile Modbus diagnostic program. It will be of interest to device manufacturers, software developers, system integrators and field service engineers. Modsak can be used to test or simulate almost any device or system that uses the Modbus protocol: slave devices, PLC's, HMI's, MMI's, DCS's, RTU's, SCADA systems, bridges, gateways, device servers, etc.
-
product
CAMAC Controller With USB Interface
CC-USB
The CCUSB is a full-featured CAMAC Crate controller with integrated high speed USB-2 interface and full CAMAC dataway display. It supports Master and Slave operations with complete CAMAC arbitration as well as auxiliary CAMAC controller operation.
-
product
NI-9145, 8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis
784756-01
8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis - The NI‑9145 is a rugged EtherCAT slave chassis for adding deterministic, distributed I/O to any CompactRIO, PXI, or industrial controller with two Ethernet ports. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. You can daisy chain multiple NI‑9145 slave chassis from the master controller to expand time-critical applications to higher channel counts while maintaining hard determinism with minimal processor resources.
-
product
Serial Bus Buffers, Extenders, and Accelerators
The Analog Devices family of I2C solutions support hot swappable, 2-wire bidirectional bus buffers to allow I/O card insertion into a live backplane without corruption of the data and clock busses. Additional supported 2-wire buses include SMBus, PMBus, the ATCA intelligent platform management bus (IPMB), and the HDMI DDC bus. I2C/SMBus Accelerators improve bus transitions to allows multiple device connections or a longer, more capacitive interconnect, without compromising slew rates or bus performance. ADI's software-programmable and pin-selectable I2C multiplexers help resolve I2C address limitations, increase fan-in or fan-out, and integrate bus buffers and rise time accelerators for an all-in-one solution. Resistor configurable I2C address translators can be configured with over 100 unique slave addresses to allow multiple slave devices with the same address to coexist on the same bus.
-
product
XMC Module
XMC-FPD-xxx
XMC Bus VITA 42• 3.3V I/O, 5V tolerant businterfaces• Local Bus Clock rates at66MHz• Compliant PCIeSpecification, r1.0a x1• Direct slave data transfers• DMA Capability• Up to 160Mb/s Transfer• DMA Transfer per Fifo Level
-
product
Dual Channel Digital Receiver
MS 1740
Dual Channel Digital Receiver is a complete high−frequency dual−channel A/D converter capable of sampling rates up to 210 MHz. It accepts two front panel analog inputs and delivers digital output samples over four FPDP (Front Panel Data Port) connectors utilizing FPDP standards. The Dual Channel Digital Receiver features two 12−bit Analog Devices AD9430 A/D Converters, and two user−configurable Xilinx® Virtex−IV Series FPGAs. It also features a VME A64/D64 slave interface for setting up operating modes and selectable A/D range, and optionally provides 32−bit access from the VMEbus to the FPGAs. It is an ideal system as a high−speed data acquisition front end for real time recording and digital signal processing systems.
-
product
Comprehensive Simulation of Master, Slave and End Nodes in A 2 B ® Networks
Infotainment Test Device ITD 1024
The complexity, cost and weight of audio systems are significantly reduced with the Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. Regardless of their hierarchical structure or use as master or slave, all A 2 B ® products must be adequately tested before use. This applies, for example, to HiFi amplifiers/loudspeakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators or sensors.Our small and very compact infotainment test system ITD 1024 takes on this task for you: It comprehensively and extremely reliably tests all A 2 B ® signals and communication in all phases of the product development process - during development, for validation and in production.
-
product
Wiring Boxes
Radio receiver for heating / cooling systems equipped with an integrated antenna, an output with SPDT relay and an RS485 Modbus® RTU slave communication port.
-
product
Ethernet to Modbus RTU Interface
Model 9099
* Use Modbus TCP/IP, VXI-11, or Raw Sockets (Telnet) or to control Modbus RTU slave devices.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Interfaces with PLCs or any Modbus TCP/IP Controller.* Fully VXI-11 compliant.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the Modbus network or devices.* 9099 is a 2x to 5x faster than the 8099 and includes a new Modbus device control page.
-
product
PCI Express to VME Interface
SIS1100-E2/3104-2
The SIS1100-e2/SIS3104-2 interface/bus coupler is the choice for demanding VME readout applications. VME block tranfser speeds up to 160 MByte/s are readily accomplished in conjunction with state of the art VME slave hardware.
-
product
Pulse
*MODBUS Master RS485 / RS232*Up to 10 slaves or 15 registers per slave*Monitoring and supply of power to the sensor*Local and remote configuration
-
product
Modbus Data Acquisition
The Datexel range of Data Acquisition equipment includes Modbus RTU Masters and Slaves, Modbus Input, Modbus Output Modules, Modbus Isolation Modules and Modbus Repeaters. The range also includes converters (RS485, USB, RS232, RS422, TCP-IP). By combining these units with the DAT3000 and DAT10000 series a complete solution for your Data Acquisition can be found from Datexel. The DAT9550 is a remote Modbus display unit that can be programmed to accept data from Modbus slaves or masters such as a PLC or the DAT9000 range of Modbus controllers.
-
product
IP Cores
logicBRICKS IP Cores by Xylon - for applications including compact multilayer video controller, versatile video input, multiview 3D transformation engine, image signal processing (isp) ulstraHD pipeline, high dynamic range pipeline, scalable 3d graphics accelerator, DDR3 SDRAM Memory Controller, slave hssl controller, HDR image signal processing framework, video design framework for multi-camera vision applications, and more
-
product
Relay
40-145-101
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
PCI CONET Controller
A2818
The Mod. A2818 is a 32-bit 33 MHz PCI card, which allows the control, through a standard PC, of up to 8 CAEN Optical Slave Cards (CAEN VME Bridge or Digitizers). The communication protocols used are the CONET1 or the new CONET2 (A dedicated firmware for the desired protocol must be installed on the board).
-
product
6th Generation Intel® Core™ i7/i5/i3 Processor-Based Automation Control System with EtherCAT & 4CH GigE Vision Support
Talos-2000 Series
ADLINK's Talos-2000 Series ready-to-use automation control system, powered by 6th Generation IntelR Core? i7/i5/i3 processors, provides EtherCAT control and four independent PoE (power over Ethernet) ports, with data transfer rates up to 4.0Gb/s. The Talos-2000 Series offers motion control of up to 64 axes, 10,000 I/O points, and 4CH PoE camera connectivity with minimal footprint. The ideal solution for machinery automation, Talos-2110 integrates complete APIs for multi-dimensional, highly synchronized and time-deterministic event-triggered motion & I/O control, high precision image capture, and data transmission. Field device connectivity in the Talos-2000 Series is provided through RJ45 connection for easy installation, and the latest 6th Generation IntelR Core? i7/i5/i3 processors enable powerful and flexible EtherCAT slave control, broad PoE camera compatibility, and compact size.
-
product
Modbus Controllers
Datexel has a range of Modbus RTU Masters, Slaves, Controllers, Data Loggers and Modbus remote displays. The DAT9000 is a Modbus RTU Master with RS485, RS232 and Ethernet Interfaces. The DAT9000IO is similar to the DAT9000 but it has digital input and outputs. The DAT9000DL has an additional Data Logging facility and the DAT9000DLIO has both Data Logging and digital IO. The DAT9011 is a Modbus Master with 2 analog inputs which can chose from Thermocouple's, RTD's, Potentiometers, mA and mV's. It also has 2 outputs which can be mA or voltage. The DAT9011 can also accept digital inputs and provide 2 SPDT relay outputs. The DAT9011DL also has a Data Logging facility which can store up to 8gb of readings on a thumb drive.
-
product
Modbus Register Converter
Model 2390
* Converts Modbus Registers and variables for replacement Modbus devices.* Maintain existing software when upgrading Modbus systems.* Provides serial control of Modbus RTU devices from any ASCII source.* User defined Register Conversion Table supports all Modbus RTU devices.* Internal Register Conversion Tables for Watlow F4-to-EZ-ZONE and F4-to-F4T conversion.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes baud rate conversion capability.* Uses SCPI commands to load the Conversion Table and set serial settings.* Small metal case mounts on a DIN rail or on any flat panel.* 239x Table Loader Program uploads the 2390 Register Conversion Table from an Excel csv file.* 239x Serial Keyboard Program provides instant control of the 2390 and Modbus Slave Devices without writing a program.
-
product
XYZ Color Sensor
AS7261
Calibrated XYZ color sensor provides complete, integrated platform for handheld color analyzers, color calibration and mobile analysis devices. Tri-stimulus XYZ realized by silicon interference filters. UART or I²C slave digital Interface. 16-bit ADC with digital access. Programmable LED drivers. 20-pin LGA package 4.5mm x 4.7mm x 2.5mm, with built-in aperture. Compact true-color sensing. Applications; Color/CCT sensing, Fluid or reagent analysis, Color point comparison, Display calibration.
