Carriers
Carrier devices are practical for adapting your product to a standard interface for testing on the bench or in the chamber.
-
product
Mezzanine Carrier
HMNS AXIe-0
The HMNS AXIe-0 module is a carrier of mezzanine modules made in the AXIe-0 standard. The module ensures the functioning of various modules installed in it, made in the form of mezzanines. The HMNS AXIe-0 module is intended for use as a carrier of mezzanines in multichannel systems for collecting/issuing information of both digital and analog types.
-
product
Arowana PCI Express SSD Board Family x1 PCI Express Gen 3 SSD Board
SKU-090-31-x1
The Arowana PCI Express SSD board is the smallest carrier board on the market. This PCI Express Carrier board was designed to expand modern motherboards or embedded systems that have a PCI Express interface. It can also be vertically installed in any 1U servers or appliances.
-
product
Bi-Phase Modulators
PMI's line of Bi-Phase Modulators includes a comprehensive selection of different models which cover broad octave frequency bands ranging from 0.5 to 40 GHz. Bi-phase modulators take a TTL level digital bits stream that’s encoded onto the RF carrier using 2 Phase Shift Keying (2PSK) modulation, where the 2 phases are separated by 180º. This performance is desirable in communications systems, microwave radio, radar, high data rate test & measurement, serial data transmission, base station infrastructure, and other industrial and military applications.
-
product
FM Tokenless Transmitter & Receiver
MS 1522
Transmitter and Receiver units are designed to work at 24V DC voltage (nominal) with variation between 19.2 V to 28.8V. The system is designed to work with carrier frequency 1800/2700 Hz and modulated frequency 65Hz/85Hz. For 1800Hz Carrier Frequency RED border is used in Front Panel and for 2700Hz Carrier Frequency BLUE border is used in Front Panel. Maximum power consumed by transmitter and receiver are 1.2W and 8W, respectively. Sense level for receiver is less than –19 dBm and No sense level for receiver is more than –22 dBm with 1mw (0 dBm) transmitter power. The equipment is designed to work satisfactorily with temperature variation from 0°C to 55°C with relative humidity of 95% at 35°C. Suitable test points are provided in the back of the equipment to monitor the necessary parameters.
-
product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - 3U VPX
Model 5953
- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional VITA-66.4 optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA-46, VITA-48, VITA-66.4, VITA-57.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products- Model 4801 Carrier Design Kit for designing custom carrier for the Model 6003 QuartzXM- Model 6003 unique QuartzXM eXpress module enables migration to other form factorsPentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products VideoLive Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boardsPipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoCSynchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPXPlease refer to the product datasheet for Installed FPGA IP Module details
-
product
Squid Carrier Board™ Family PCI Express Carrier Board for 8 MiniPCI Express Modules
SKU-085-01
Squid PCI Express Carrier board for MiniPCIe modules is the first product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 8 MiniPCI Express half or full-size MiniPCI Express modules to the one motherboard’s PCI Express slot.
-
product
Mux-scrambling Modulator 8 Ch
SFT3394C
Hangzhou Softel Optic Co., Ltd.
SFT3394C is a high performance and cost-effective QAM modulator designed by Softel. It has 16 DVB-S/S2 FTA tuner input to 16 non-adjacent carrier output with multiplexing, scrambling and QAM modulating included. It also supports maximum 512 IP input port and one IP (MPTS) output through GE1 and TS input for re-mux through 2 ASI ports. SFT3394C is also characterized with high integrated level, high performance and low cost. It supports dual power supply (optional). This is very adaptable to newly generation CATV broadcasting system.
-
product
USB 3.0 Type A (With Shielding) Test Connector
Test connector for USB 3.0 Type A with shielding (9 pole) for contacting USB interfaces. Application in high-speed USB devices like hard disks, data carriers, power supplies, etc.
-
product
Compact PCI Express (3U) Generic Carrier Card
ACCx-1
To complement the wide range of interface modules for dedicated Avionics Databuses and Networks, AIM offers a range of Carrier modules for the use of AIM or any 3rd Party PMC and XMC module on various backplanes.
-
product
SparkFun FM Tuner Basic Breakout
Si4703
This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user.
-
product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - 3U VPX
Model 5950
- Now available in RFSoC Gen 3 with the Model 5953- Multi-board synchronization with Quartz RFSoC video- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional VITA-66.4 optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA-46, VITA-48, VITA-66.4, VITA-57.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products- Model 4801 Carrier Design Kit for designing custom carrier for the Model 6001 QuartzXM- Model 6001 unique QuartzXM eXpress module enables migration to other form factors- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Synchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPX
-
product
Quad QSFP28/QSFP+ FMC+ Module
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
product
PCI Generic Carrier Cardfor PMC (PCIbus Mezzanine Card) Modules
ACP-1
PCI generic carrier card for PMC (PCIbus mezzanine card) with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
Press Down Rods Bed of Nails Testers
Prober Press Rods Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
PCIe Gen 3 ATCA Carrier With Low-Power Xeon E3
ATC123
The ATC123 is a Carrier Module with an onboard x16 PCIe Gen3 slot (only x8 PCIe is routed to the slot) to accept any standard PCIe edge type module.
-
product
AMR Module Warm-up Station
3206G
The Model 3206G Meter Warm-Up Station for AMR Modules has been specifically designed for meters that utilize the DCSI TWACS™ power line carrier communications module. Additionally, this versatile unit includes voltage output and voltage input connections that allow you to test additional brands of power line carrier modules when using the manufacturer’s supplied module. The Model 3206G can even be used as a simple meter warm-up station.
-
product
Satellite Carrier Reconnaissance and Analysis System
SCL-SACRAS
Shoghi’s Satellite Carrier Reconnaissance and Analysis System (SCL-SACRAS) is capable of detecting Point-to-Point satellite links, which work for international Voice networks, GSM Abis backhaul links, IP links and VSAT networks of major VSAT manufacturers including iDirect, Hughes, Gilat, Eastar Romantis, Comtech; including the various types of proprietary protocols and services running on them.SCL-SACRAS can be utilized for the carrying out the detailed reconnaissance of satellite carrier frequencies running on various target satellites, for identification of target carriers for regular monitoring which are of the customer’s interest. Military or intelligence agency customers can utilize this system to identify the target links on respective satellites for continuous monitoring, using the Shoghi VSAT Monitoring System.
-
product
3rd Gen MicroTCA Carrier Hub (MCH), 40GbE/PCIe Gen 3
UTC004
The VadaTech UTC004 is the most feature-rich MicroTCA Carrier Hub (MCH) on the market. Its management software is based on VadaTech’s robust Carrier Manager and Shelf Manager which have been deployed for years with proven results. The MCMC manages the Power Modules, Cooling Units, and up to 12 AMCs within the chassis. It also manages the optional PCIe Gen3, SRIO Gen2, 40GbE/10GbE or Crossbar Fat Pipe switches as well as the standard GbE with 10GbE uplink Base Channel switch.
-
product
Floating-Point C6678 DSP Module
FMC667
Sundance Multiprocessor Technology Ltd.
The FMC667 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6678 device. The FMC667 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces. Several Gigabit differential pairs from the FMC connector are used to implement a PCIe and Serial Rapid IO interface between the FMC and the carrier.
-
product
IP QAM
SFT3332 (-D)
Hangzhou Softel Optic Co., Ltd.
SFT3332 (-D) IP QAM modulator is Mux-scrambling-modulating all-in-one device developed by SOFTEL. It has 32 multiplexing channels, 32 scrambling channels and 32 QAM (DVB-C) modulating channels, and supports maximum 1024 IP input through the GE port and 32 non-adjacent carriers (50MHz~960MHz) output through the RF output interface. The device is characterized with dual RF output ports which broaden the bandwidth for QAM carriers.
-
product
Synchro/Resolver Conversion & Simulation PMC boards
Versatile, rugged, and time saving Synchro/Resolver conversion and simulation PMC boards featuring multiple high accuracy, independent channels and easy programmability, to provide a highly accurate and convenient method to test and simulate positioning systems in lab and embedded environments. The SB-3642 conversion and SB-3644 simulation boards’ versatility and ruggedness enable them to be used first in the lab, and then be readily designed into embedded applications, just by the switch of a carrier card.
-
product
PCI Board
SMT835-ZU47DR-2
Sundance Multiprocessor Technology Ltd.
The Sundance SMT835-ZU47DR-2 is a PCI express ZynqRF system comprised of the TEB0805 carrier board and the TE0835-02-TXE21-A RFSoC module.
-
product
Virtex 7 FPGA Carrier
PC7: 330/690
The PC7 family of FPGA carrier boards is DEG’s latest AMD-based product innovation. With the ability to host two FMCs (FPGA Mezzanine Cards) with rear panel I/O, the PC7 product line sets the benchmark for performance and versatility in the embedded PCIe market. Coupling this flexibility with a AMD Virtex-7 VX330T or VX690T FPGA, the PC7 enables multi-channel high-speed data acquisition and extensive digital signal processing all within a single PCIe slot.
-
product
CAN Bus & ARINC-825 (825CAN)
The 825CAN module is an intelligent multichannel ARINC 825 (CAN bus) interface module for the multiprotocol Excalibur 4000 & 8000 family of carrier boards. The module supports up to ten ARINC-825 channels. In receive mode, the module stores all or selected messages with status and Time Tag information appended to each message. In transmit mode, the module operates via a transmit Bandwidth Frame which allows scheduling of data transmissions and reduces the need for host computer intervention.
-
product
FMC-LPC I/O Module
FM191
Sundance Multiprocessor Technology Ltd.
The FM191-RUA1 has a VITA57.1 FMC-LPC connector and follows the electronics specification and recommendations of the standard but is NOT form-factor compatible and will NOT fit all FMC carriers. Two versions are available. The FM191-R main features are a daughter card which provides 5V-TTL-compatible Analogue and Digital GPIOs that are suitable for robotics, motors and sensor application.
-
product
Connector Adapter
MCA-ST connector adapter for the connection of micro plugThe connector adapter allows the direct connection of fine-pole connectors on circuit carriers or jumpers. The adapter is guided over the connector housing, which overcomes the tolerances of carrier and mounting.
-
product
PMC Carrier Module
DP-VME-5114
DP-VME-5114 is a VME-Based PMC Carrier Module. This 6U VME board PMC carrier can accommodate two PMCs. This board can be used for data acquisition, automated testing and checkout systems
-
product
MTCA.4 Power Supply
To match the requirements of the next generation of “carrier grade” communication equipment the PCI Industrial Computer Manufacturers Group PICMG created in 2002 a new standard AdvancedTCA / ATCA. The ATCA crate backplanes are based mainly on 48V industrial power supplies. From this form factor evolve the Advanced Mezzanine Module carrier card AMC form factors defined in AMC.3 in types of single or double width.
-
product
PCIe Gen 3 ATCA Carrier Low-Power Xeon E3
ATC122
The ATC122 is a Carrier Module with an on board x16 PCIe Gen3 slot to accept any standard PCIe edge type module. The module has dual 10GbE connected to the Fabric channels and dual GbE to the base channels. It comes with 32 GB of ECC memory. It also has an option for Trusted Platform Management (TPM).
-
product
cPCI to PMC Adapter / Carrier
cPCI2PMC
The cPCI2PMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCI2PMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation. The PMC user IO connector Pn4 is optionally connected to J2 for rear panel IO.
