Strain Gauge Amplifiers
-
Product
Gauge Type T Thermocouple Wire
W-TW-44P2
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
2 Channel Microphone Power Supply and Conditioning Amplifier
SoundConnect 2 mic power supply
-
SoundConnect 2 is a rugged 2-channel USB controlled microphone power supply and conditioning amplifier.
-
Product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
Terminal Board
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
10mA One-Channel Amplifiers
-
USB connected devices have become common in lab environments. The nano box USB is a standalone piezo amplifier with 16 bit D/A resolution. Its small size and powerful amplifier includes a USB 2.0 interface that offers a variety of helpful commands.
-
-
Product
RF Amplifier Modules
-
Analog Devices RF amplifier modules offer high linearity, low noise figures, and low phase noise, as well as low power consumption. These devices are all fully specified over frequency and temperature for use in a variety of applications.
-
Product
Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Compact / Cable Type]
PM-45
-
Panasonic Industrial Devices Sales Company of America
Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Compact / Cable Type]
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
-
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Testing)
PA60Bi
-
PA60Bi is the panel-mounted power amplifier, which can produce 3-phase current, with maximum RMS phase current of 60A and maximum output power of 800VA, and 4-phase voltage, with maximum RMS phase voltage of 120V and maximum output power of 60VA.
-
Product
Large Calibre Barrel Bore Gauge System
BG20
-
Aeronautical & General Instruments Ltd.
The BG20 has been specifically designed to modernise and improve the inspection routines of large calibre barrels. A two-point measuring head is supported in the barrel or chamber by a clear disk which facilitates the angular alignment of the head and the location of a suspected defect.
-
Product
Optical Parametric Amplifier
-
AVUS is an Optical Parametric Amplifier (OPA) that provides widely tunable high energy pulses and high repetition rates (up to 1 MHz). AVUS offers highest average output power on the market and is designed for 1 µm fs pump lasers.
-
Product
EYDFA Amplifier
-
a high-power, versatile amplifier designed for optical communication and other general-purpose Polarization Maintaining (PM) optical amplification applications. This compact module housing ideal for OEM integration applications.
-
Product
Industrial Protective Coating Thickness Gauge
456 IPC
-
The Elcometer 456 Industrial Protective Coating Thickness Gauge1 is designed to measure dry film thickness on shot or grit blasted steel substrates.
-
Product
Digital Tire Pressure Gauge 230 PSI
AstroAI ATG230
-
Green Backlit LCD display and flashlight for visibility in dimly light areas, easy-to-read digits help you easily measure your vehicle's tire pressureHeavy Duty Stainless Steel Made And RV/Truck Special Designed to maintain correct tire pressure, reduce tire wear and extend tire life; Digital display reading instantly and clearly being shown, no longer do the guesswork of analog gaugesBi-directional push-pull (Dual) head design; Nozzle easily forms a seal with the valve stem giving quick and accurate readings in 0.1 increments; 4 settings with longer range: 0-230 PSI / 0-16 Bar / 0-16 Kg/cm2 / 0-1585 Kpa
-
Product
High Power RF Amplifiers
-
Corry Micronics' line of high power RF amplifiers feature up to 40% efficiency. an extended temperature range of -30 degC to 55 degC for MIL-STD applications, and status monitoring signals that provide diagnostic information.
-
Product
Power Amplifier (DC Powered)
-
RF Lambda’s DC solid state power amplifiers (PA) are used in a variety of applications and offer high output power, wide band operation and good linearity. Hermetically sealed options are available upon request.
-
Product
RF Bidirectional Amplifiers
-
Miniature, high-efficiency and linear bidirectional amplifier modules (transmit and receive). 1.0 to 2.5 GHz, automatic or manual T/R switching, high-efficiency or high-linearity models. Custom designs available through RF PA design services.
-
Product
Multifunction Engine Gauge
1U378-series
-
This 3” instrument combines the three essential engine parameters in a compact package. Rugged D’Arsonval meter movements with two jewels are used to indicate cylinder head and oil temperatures. A brass bourdon tube mechanism precisely indicates oil pressure. A selection of fittings is available to simplify installation.
-
Product
Portable Power Amplifier
PA30Bip
-
PA30Bip portable power amplifier is designed with linear amplifier principle. It is very light portable solution with three channels of current output and four channels of voltage output.
-
Product
Dual Relay Trip Amplifier for RTD and Slidewire Sensors
SEM1633
-
The SEM1633 provides an accurate alarm / switching function when used with RTD or Slidewire sensors. Other sensor characteristics or your own 22 point linearization characteristic (for slidewire or linear resistance) can be downloaded into the product enabling you to adapt it exactly to your application.
-
Product
sbRIO-9236, Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781580-01
Strain/Bridge Input Module
Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
Product
Pulsed ESR/EPR: Pulsed Injection-locked IMPATT Amplifiers
-
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
Digital Pressure Gauge
-
Precision digital pressure gauges are suitable for stationary and also mobile measurement and display of pressures. In addition, a digital pressure indicator can be used as a pressure reference and enables the easy testing, adjustment and calibration of other pressure measuring equipment directly on site. Through efficient measuring cells with electronic linearisation of the characteristic curve, a high accuracy is achieved.
-
Product
Ergonomic Force Gauges
DMG Series
-
AMETEK Sensors, Test & Calibration
The DMG ergonomic gauge lets you objectively measure manual muscle strength and functional task requirements for almost any application.
-
Product
Power Amplifier
2734
-
The 2734 is a compact class D power amplifier, intended for acoustical measurements in the field or laboratory. All controls and connectors are placed on the front panel, enabling you to set up the 2734 very quickly, and to operate it in horizontal or vertical position. The 2734 is built into a robust flight case making it safe and easy to carry along.
-
Product
Cable Tray, Slide Configuration, For Strain Relief And Cable Management, For 28" And Longer
310113424
Cable Tray
Strain Relief.
-
Product
CATV Multi-ports Output High Power Full Function Optical Amplifier Module
HHOA-F5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HHOA-F5000 series is a kind of multi-port output, high power, full-function optical amplifier module and is suitable for CATV with low noise. Its total output power is 27~40dBm (0.5W~10W) optional and its optical output port can reach to 64 pieces at most. The module has standard RS232 interface, adopts high reliable and low power consumption design as well as adopts APC, AGC control mode. The product has two series: The output power of Huatai HHOA-F5000 high power optical amplifier module can be chosen in the range of 27dBm~40dBm. According to different output power, Huatai HHOA-F5000 adopts two latest technical solutions. One is to use single mode high power 980nm pump laser with cooling and EDF, multi-pump synthesis technique. The other is to use multi-mode high power 980nm pump laser without cooling and double-clad Er-Yb doped fiber-optic technology. It provide a whole set of high reliability, low cost, low noise and low power consumption solutions for the application of high power, multi-port output amplifier. It can be widely used in CATV head-end or FTTx distribution network.
-
Product
Low Noise High Precision High Voltage Amplifier
WMA-280
-
The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.
-
Product
Synchro Power Amplifiers
SSP
Amplifier
Computer Conversions Corporation
The SSP Series are Compact, Reference Powered and Isolated Synchro Power Amplifiers, and AC Sine/Cosine ( Resolver ) to synchro converters; designed for moderate wattage, and re-transmission requirements; providing ultra high efficiency, and ultra high reliability in service, and ease of use. They are ideally suited for demanding Naval/Maritime, Aircraft, and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and active control systems. They are suitable to drive both CT and CDX type passive loads, and virtually any synchro input instrumentation, or control.
