Additive White Gaussian Noise
-
Product
Interferometers (White Light)
interferoMETER
-
The innovative white light interferometers from Micro-Epsilon set a benchmark in high-precision distance and thickness measurements. These sensors enable stable measurement results with sub-nanometer resolution offering a comparatively large measuring range and offset distance. The interferometers are available in 3 series: the IMS5400-DS for high-precision industrial distance measurements, the IMS5400-TH for accurate thickness measurements and the vacuum-suitable IMS5600-DS for distance measurements with picometer resolution.
-
Product
Analog Noise Generator
PNG7000
-
The PNG7000A Series instruments generate white Gaussian noise and provide a summing input to control signal-to-noise (SNR) or carrier-to-noise (CNR) for bit-error-ratio (BER) testing. The output can also be used as a source for Jitter applications.
-
Product
Power, Patchcord, Receiver, 72", Mini Power, 40 Amps, 12 AWG White, Single Ended
7-232912000-072
Power Patchcord
Power, Patchcord, Receiver, 72", Mini Power, 40 Amps, 12 AWG White, Single Ended.
-
Product
Surface-Mount Noise Sources
-
Mercury’s family of surface-mount noise sources provides exceptional performance in a compact and easy to integrate package. These products are ideal for applications such built-in test and dithering circuits where the system requirements drive a need for compact, surface mount technology.
-
Product
High Power Noise Sources
NS-7001
-
The NS-7001 is high-power noise source specifically designed to operate in the 2.11-2.17 GHz UMTS band. It features flat output power that is regulated over a wide temperature range with high rejection outside the operating band of interest. Logic control is provided to enable/disable the noise source and an internal BIT function continuously monitors the output power. Other frequency bands and power levels are available.
-
Product
Low Noise Amplifier
ZLNA-9K-6G-01
-
Low Noise Amplifier, Frequency 0.009~6000MHz, Gain 40dB, Noise figure 3.5dB, P-1dB power 8dBm, SMA Female
-
Product
Ultra Low Noise Preamp
J2180A
-
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
Product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
-
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
Product
Low Noise Triple Band Voltage Controlled Oscillator
-
This Low Noise Triple Band Voltage Controlled Oscillator was designed to meet a specific customer requirement. The VCO cover the 3300 to 4700 MHz frequency range in three bands. The output power is +9 to +12 dBm with an integrated buffer amplifier to minimize load pulling. The three bands are selected using standard TTL control.
-
Product
Abnormal Noise Detection System In-Line Tester
MV-6000B
-
This product sets criteria found with waveform analysis software, and runs automatic judgment in-line.
-
Product
Fast Low Noise SWIR InGaAs Camera
C-RED 2
-
C-RED 2 is a revolutionary ultra high speed low noise camera designed for high resolution Short Wave InfraRed imaging. Thanks to its state of the art electronics, software, and innovative mechanics, C-RED 2 is capable of unprecedented performances: up to 400 images per second with a read out noise from 10 to 30 electrons. Designed for high-end SWIR applications, smart and compact, C-RED 2 is operating from 0.9 to 1.7 μm with a very good Quantum Effi ciency over 70%, offering new opportunities for industrial or scientifi c applications.
-
Product
Whiteness Meter
-
Widely used in Floor maintenance, Surface cleaning quality control, Stone and tile gloss measurement, Checking printed matter, Quality control of paint and ink, Polished metal surface ,measurement (chrome plating), Inspection of paint protection and waxing, Auto-body paint inspection, Surface inspectionof plastic moldings, Evaluation of detergents and washers, Checking masonry and washers, Checking building exteriors.
-
Product
NBS-Series Cryogenic Primary Noise Standards
-
The NBS-Series provide the ultimate accuracy when measuring extremely low noise figures (noise temperatures).
-
Product
Portable 4-channel Noise & Vibration Analysis System
WCAmini AD-3661
-
* USB bus power unit * 24 bit, 4-channel measurement * A channel exclusively for tacho pulse measurements * WCAPRO (multi analysis software) * FFT analysis and real-time octave analysis * Tracking analysis and throughput recording/playback * Equipped with WCA Lite (easy-to-use analysis software)
-
Product
Additional Products: 68 Pin 1.27mm Pitch Micro-D Cables - 68 Pin to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
14 Slot, 3U, 350W, PXI Chassis - Low Noise Fan
40-914-201
Chassis
This PXI chassis includes all the features and performance required by the PXI standard and supports a control interface or embedded controller and up to 13 more 3U peripheral modules.
-
Product
Acoustical Random "Noise" Generator
ARNG-2000
-
Eliminate and Defeat otherwise undetectable distance surveillance devices such as Microwave, Laser and Boom Microphones
-
Product
Noise Bridge, RF 1 MHz to 100 MHz
MFJ-202B
-
Quickly adjust almost any antenna for maximum performance, 1 to 100 MHz. Lengthen or shorten your antenna for minimum SWR. Measure resonant frequency, feedpoint resistance and reactance. Works with any receiver or transceiver. Hand-calibrated resistance scale, expanded capacitance range and exclusive built-in range extender.
-
Product
6.5 Digit Low Noise Power Source
B2960 Series
-
The Keysight B2960 Series 6.5-digit low noise power source are a new generation of power sources offering precision, wide bipolar output ranges, and other innovative features such as graphing capability and arbitrary waveform generation capability, enabling test and evaluation that conventional power sources cannot do.
-
Product
Signal, Patchcord, ITA, 72", QuadraPaddle, 24 AWG White Twisted Pair, Single Ended ( 5 Amps)
7-121424000-072
Signal Patchcord
Signal, Patchcord, ITA, 72", QuadraPaddle, 24 AWG Twisted Pair White/Black, Single Ended (3 Amps)
-
Product
Amplified Noise Modules
NC1000 Series
-
The NC1000 Series amplified noise modules produce AWGN as high as +13 dBm, and have bandwidths up to 10 GHz. The high power modules are designed to test noise immunity for Cable TV equipment, secure communication channels, and military jamming systems. The lower power modules, <= 0 dBm, are random jitter sources for many applications including, PCIexpress, Infiniband, and 10 GigE.
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG White, Single Ended (3 Amps)
7-121924000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG White, Single Ended (3 Amps).
-
Product
Signal Patchcord, ITA, TriPaddle, 36", 16 AWG White, Single Ended, (10Amps)
7-101916000-036
Signal Patchcord
Signal Patchcord, ITA, TriPaddle, 36", 16 AWG White, Single Ended, (10Amps)
-
Product
Ultra Low Noise Disciplined Frequency 4220a Standard with Rubidium and OCXO Clean-Up Oscillator
-
Precise Time and Frequency, Inc.
The ptf 4220A is an Ultra Low Noise Disciplined Frequency Standard with rubidium and OCXO clean-up oscillator.The instrument contains a high performance rubidium module, with an extended life design, and very low aging rate, with high quality OCXO o/p for low phase noise.
-
-
Product
10 MHz to 55 GHz Noise Sources
CNS346 Series
-
The Spanawave CNS346 Series is designed for precision noise figure measurement applications. The superior VSWR characteristics reduce multiple reflections of the test signals and significantly increase the measurement accuracy of most noise figure set-ups. The CNS346 Series noise sources have broadband coverage and extremely good temperature and voltage stability, for the finest noise figure meter-compatible laboratory standards. Outputs of 6, 15.5 and 22 dB ENR are available, allowing the units to accurately measure noise figures up to 20 ,30 and 36 dB respectively.
-
Product
E-Band Low Noise Amplifier MMIC
AWL-7186
-
The AWL-7186 is a 4-stage ultra-low noise amplifier that provides a noise figure of less than 3.5 dB, an output P1dB of +8 dBm, and an adjustable gain range of 15 dB. The MMIC features exceptional gain flatness and superior noise performance over a very wide bandwidth. It is implemented in 0.1 um GaAs PHEMT technology.
-
Product
Noise Suppression Products / EMI Suppression Filters / TVS Diodes (ESD Protection Devices)
-
Murata noise suppression products include compact EMI suppression filters that efficiently eliminate noise, L Cancel Transformers (LCTs) that greatly suppress noise in high-frequency bands by reducing the ESL generated inside capacitors and in boards, and TVS Diodes that guard semiconductor devices against electrostatic discharge from external sources. Murata supplies products that support a variety of approaches to suppressing noise.
-
Product
SNR Noise Generator
CNG-EbNo
-
The CNG-EbNo is a fully automated precision signal to noise (AWGN) generator that sets, and maintains a highly accurate ratio between a user supplied carrier and internally generated noise, over a wide range of signal power levels and frequencies. The internal AWGN meter provides repeatable SNR waveforms for accurate signal generation. The instrument gives system, design, and test engineers in the telecommunications industry a single tool to generate precision signal to noise ratios. These signals are used to compare theoretical BER to SNR ratios, found in "waterfall" type graphs, with measured values from the DUT to evaluate different modulation schemes. Users can obtain higher yield through automated testing, plus increased confidence from repeatable, accurate test results. Standard units can be modified for specific customer requirements. Please consult the factory for pricing and availability of these requests.
-
Product
Low Noise Test Leads For N1413 With B2980 Series, 3m
N1425B
Coaxial Cable
The N1425B is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425B is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425B enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425B to the B2985B/87B.
