Product

Fineliner

-

MicroContact AG

MicroContact AG

The parallel tester Fineliner enables two-sided contact with fne structures. Withvisual detection of both substrate sides and corresponding adapter position correction≥ 300μm test points can be contacted. The rigid needle adapter with a pitch of ≥ 400μmalso allows a high contact density. This results in a large test depth on the substrate.The integrated DMC reader ensures a correct test result assignment. Multiple PCB canbe tested step by step through in the X-direction of the Fineliner, further eliminatingsubstrate tolerances in the X-direction, and enabling more cost-effective adapters andmeasurement techniques. A quick-release system with identifable replacement kitsensures safe and quick retooling.The measuring technology can be defned customer-specifcally. There are 2040 pyloninterface points per side.

Product

Multiport JTAG Tester

XJQuad

-

XJTAG Ltd.

XJQuad - XJTAG Ltd.

XJQuad is a 4-port version of the XJLink2 USB-to-JTAG controller targeted at PCB manufacturers. It is supplied with XJRunner software for running XJDeveloper test systems. With a range of special features it is particularly suitable for concurrent/parallel testing on the production line. Each of the four ports has a high-speed interface which can be connected to up to four JTAG chains on each Unit Under Test (UUT).

Product

Diagnostic Solution

SYSTEM 8 Diagnostic Solution PLUS

-

ABI Electronics Ltd

SYSTEM 8 Diagnostic Solution PLUS - ABI Electronics Ltd

The SYSTEM 8 Diagnostic Solution PLUS is the solution to board fault-finding problems. Equally at home with analogue and digital PCBs, the systems 64 digital and 24 analogue test channels provide a variety of test and measurement techniques to track down the most elusive faults.

Product

Module Spectrum

nRF52832 Series

-

Raytac Corp

nRF52832 Series - Raytac Corp

Raytac nRF52832 module spectrum covers MDBT42Q, MDBT42 and MDBT42V series with both Chip Antenna and PCB Antenna option for selection.

Product

Multi-layer Short Circuit Locator

Toneohm 950

-

Polar Instruments Inc

Toneohm 950 - Polar Instruments Inc

Polar Toneohms are ideal tools for the electronics production environment. Able to locate shorts quickly and accurately on both bare and loaded PCBs, they provide a very cost-effective means of minimizing repair and rework of faulty PCBs that have been identified by pass/fail testing on an ATE system.

Product

General Purpose Pressure Sensors For High Frequency

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB® Series 113B dynamic pressure sensors set the standard for extremely fast, micro-second response with a wide amplitude and frequency range. These characteristics allow them to excel in high-frequency applications, where minimum sensor diameter is required.

Product

Structural Test ICP® Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Conventional structural test data systems use few to several hundred sensors. Cables bundles can be complex and confusing resulting in setup errors. Sensors with TEDS (Transducer Electronic Data Sheet) allow for an internal sensor digital chip to store sensor information. This information contains descriptive identifiers that when connected to a TEDS compatible signal conditioner or data system, reads the descriptive information and automatically aligns the data system. Human error is minimized, reducing time consuming data verification or re-test. The Series 333 ICP® accelerometers, and their accessories, are designed to address the needs of multi-point modal and structural test measurement applications. This equipment was developed in conjunction with the world renowned University of Cincinnati Structural Dynamics Research Laboratory and proven in real-world testing situations. The PCB 333 Series accelerometers delivers rapid system setup, reduces human documentation errors, maintains calibration data of each sensor, allows for “Plug-and-Play” installation, reduces overall test time lowering project test costs.

Product

PCB IMIC01, 100 mV/g, 2-Pin, Accelerometer, Industrial Vibration Sensor

780985-01

-

NI

780985-01 - NI

The PCB IMIC01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMIC01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.

Product

Exchangeable Test Fixture

MA 2112/D/H/S-7

-

INGUN Prüfmittelbau GmbH

MA 2112/D/H/S-7 - INGUN Prüfmittelbau GmbH

Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg

Product

ATE

QT 200 NXG

-

Qmax Test Technologies Pvt. Ltd.

QT 200 NXG - Qmax Test Technologies Pvt. Ltd.

QT 200 Nxg a Highly sophisticated ATE, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software.

Product

PCB IMID01, 100 mV/g, IEPE, 2-Pin, Accelerometer, Industrial Vibration Sensor

784175-01

-

NI

784175-01 - NI

The PCB IMID01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMID01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.

Product

Exchangeable Test Fixture

MA 2112/D/H/S-7/GR228x-15/7

-

INGUN Prüfmittelbau GmbH

MA 2112/D/H/S-7/GR228x-15/7 - INGUN Prüfmittelbau GmbH

Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,30 kg

Product

Pine Electronics

-

Pine Research Instrumentation

Pine Research Instrumentation

Specializing in low-mid volume electronic manufacturing services, Pine Electronics, Inc. offers a wide range of printed circuit board assembly (PCB assembly), cable and box build assembly solutions. Our equipment, engineering and technical talent serves both multi-national and regional customers throughout the United States. Known for full-service PCB assembly work, Pine Electronics, Inc. is highly integrated and responsive. Each customer has a designated representative for all commercial and technical questions. This personalized service model enhances communication, expedites project development, and represents Pine’s commitment to customer service.

Product

High-Temperature SOIC DIP Adaptor

SERIES 35000-10-HT

-

Aries

SERIES 35000-10-HT - Aries

High Temperature Lead Free SOIC DIP Adapters. A cost effective means of upgrading to SOIC...without changing your PCB layout. Available on .300 [7.62] centers. Consult Data Sheet No. 18011 for adapters on .400 [10.16], or .600 [15.24] centers.

Product

75 Ohm Mini SMB Connectors

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

75 Ohm Mini SMB connector category from Pasternack includes many part numbers, the majority are RoHS and REACH compliant. 75 Ohm Mini SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our 75 Ohm Mini SMB connectors are built to precise microwave and RF industry specifications. Pasternack 75 Ohm Mini SMB connectors are built in jack or plug gender with 75 Ohm impedance. Mini-SMB 75 Ohm connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel or mountless options. These 75 Ohm Mini SMB connector designs include crimp/solder or solder attachment methods. We offer 75 Ohm Mini-SMB connectors with standard or high performance levels manufactured with brass or stainless steel bodies. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm mini SMB connector series is in-stock. Not only are these mini-SMB 75 Ohm connectors in stock, they also ship the same day as they are purchased.

Product

Stand-Alone Test Fixture

MA 2013/D/H

-

INGUN Prüfmittelbau GmbH

MA 2013/D/H - INGUN Prüfmittelbau GmbH

Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 22,00 kg

Product

Combination Board Tester

ATE QT2256-640 PXI

-

Qmax Test Technologies Pvt. Ltd.

ATE QT2256-640 PXI - Qmax Test Technologies Pvt. Ltd.

Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.

Product

24-Pin SOIC w/Package-to-22-Pin 0.400" DIP

22-304504-18

-

Aries

22-304504-18 - Aries

24Pin SOIC w/ Package to 22 Pin .4 DIP. A cost effective means of upgrading to SOIC without changing your PCB layout.

Product

3D SPI Series

MS-15

-

MIRTEC Co., Ltd.

MS-15 - MIRTEC Co., Ltd.

- Exclusive 15MP / 25MP CoaXPress Camera System- Dual Projection Shadow Free Moiré Technology- Precision Compound Telecentric Camera Lens- Automated Z-Height Calibration System- Automated PCB Under Board Support System- Precision PCB Warpage Compensation- Closed Loop Communication With Screen Printer- Absolute Repeatability and Reproducibility- INTELLISYS® Industry 4.0 Intelligent Factory Automation System

Product

X-Ray Inspection System

MXI Ruby XL

-

Nordson Corporation

MXI Ruby XL - Nordson Corporation

Designed for the largest PCBs, Ruby XL allows 96 x 67 cm (37.9” x 26.4”) areas to be inspected non-destructively, with feature resolution up to 0.5 µm.

Product

High Voltage Dry Reed Relays For up to 10kV

Series 67 & 68

-

Pickering Electronics

Series 67 & 68 - Pickering Electronics

Series 67 PCB mounting with switch and coil connections in a Single-in-Line format.Series 68 PCB connections on the underside for coil connections. Flying leads from the top face for high voltage connections.The Series 67 and 68 are constructed using former-less coils. The absence of a coil supporting bobbin allows a device smaller than the industry norm. The unusual package design gives some interesting possibilities for high density packing.The option of flying leads for the high voltage connections makes it possible to keep this away from lower voltage circuitry on the pcb.Form A (energize to make) contacts are available with the option of 5, 12 and 24 volt operating coils.

Product

Manual Test Fixture (MA)

MA 2013/D/H/VPC-G12x-18

-

INGUN Prüfmittelbau GmbH

MA 2013/D/H/VPC-G12x-18 - INGUN Prüfmittelbau GmbH

Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 25,00 kg