Emulation
See Also: Emulators, Simulation
-
Product
PoE Powered Device Analyzer for 802.3at & 802.3bt
PDA-604A
-
Emulate any 802.3at Type-1, Type-2, 802.3bt Type-3, or Type-4 PSE powering 2 or 4 pairs at all possible PD input voltages. Optionally supports 802.3at and 802.3bt Ethernet Powered Device Conformance Test Suites and LLDP Emulation and Analysis.
-
Product
JTAG Emulator
Spectum Digital XDS510-USB
-
The Spectrum Digital XDS510 JTAG emulator is low cost and has a USB powered interface.
-
Product
Live PD Emulation for the PSL-3424A/L
-
Flexibly Mimic Class 0 to Class 8 Powered Device Per PSL-3424 Test Port. Configure up to 96 IEEE 802.3 PD’s on Any Combination of 2-Pair and 4-Pair PSE Ports with Loading up to 100W on Every Port. Emulated PD’s Automatically Handle PSE Power Demotions (Assigned Class). User-Defined Powered Device Load with Optional Cable Loss Modeling. Emulate 802.3at and 802.3bt PoE-LLDP* Negotiations and Power Adjustments (PSL-3424L). Monitor Multi-Port Live Emulation Status.
-
Product
Base Station Emulator
SUTP 5018
-
Designed to create a custom cellular environment to serve testing and characterization needs. The combination of high power, real-time computing and the software defined radio platform enables this instrument to create your own cells for testing in a compact size and cost-efficient way.
-
Product
Channel Emulator
-
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
Product
Smart Network Emulation for All Mobile Device Tests
CMWcards
-
Use R&S®CMWcards to prepare the tests you always wanted, but never found the time to set up. Create wireless signaling and application tests on the R&S®CMW500 wideband radio communication tester just by setting up a hand of cards – no programming required. Revolutionary card wizards and unique game rules guide you through setting up test sequences that fully comply with test specifications. Thanks to the R&S®CMW500 tester’s unrivaled multi-technology capability, R&S®CMWcards can be used to rapidly reproduce signaling scenarios for various wireless communications standards.
-
Product
Satellite and AerospaceChannel Emulation Toolset
S8825A
-
Satellite, aerospace, and airborne radio link testing with realistic wireless propagation conditions. 5G NTN test support with satellite connection from mobile phones. Interconnecting networks for full end-to-end system testing.
-
Product
Emulators
-
Comware Technical Services, Inc.
Comware’s emulators replace your legacy system with modern hardware without changing the operating system and the application software.
-
Product
Scienlab Dynamic DC Emulator
SL104XA Series
-
The Scienlab Dynamic DC Emulator provides an all-in-one system for efficient and effective testing of the power electronic components in electric vehicles (EV) and electric vehicle supply equipment (EVSE).
-
Product
Chromatic Dispersion Emulator
CS-CDE
-
The ClearSpectrum™-CDE is a chromatic dispersion emulator suited for test and measurement. This 1U half 19-inch rack-mountable module is designed to emulate tens of thousands of picoseconds per nanometer in a compact unit while maintaining very low insertion loss. It is a passive, ready-to-use emulator which can be cascaded several times to achieve higher levels of dispersion.
-
Product
Advanced JTAG Emulators
-
Blackhawk offers JTAG Emulators ranging from entry level to full-capability debug probe models supporting System Trace (STM), starting at $99. This includes XDS100v2, XDS200 and XDS560v2-class models that are compatible with Code Composer Studio.
-
Product
JTAG Emulator
Spectum Digital XDS560v2-STM
-
The Spectrum Digital XDS560v2-STM emulator has System Trace capability, along with a USB powered interface.
-
Product
UI Test Tool for Web, Java, Windows, Android & iOS
QF-Test
-
QF-Test is the established tool for professional GUI test automation of desktop, web & mobile applications as well as PDF documents. QF-Test is a low-code GUI test tool that allows you to efficiently create test cases, e.g. using Capture/Replay, without any programming knowledge across platforms on Windows, Linux and macOS. For software developers, Jython, Groovy or JavaScript offer advanced scripting possibilities. Tests can be run automatically via continuous integration tools such as Jenkins and generate detailed log files and XML or HTML reports. Use QF-Test to create robust and stable regression tests for various GUI technologies. QF-Test supports all types of Java GUIs, ranging from Swing (including ULC, JIDE components, CaptainCasa), its successor JavaFX, as well as the Standard Widget Toolkit (SWT) and Eclipse, including plugins and RCP applications. You can also use QF-Test to test dynamic web applications based on Angular, React or Vue.js, for example, including Electron and hybrid applications using JxBrowser, JPro or WebSwing, for example. QF-Test supports native Windows desktop applications created with Win32, .Net, Windows Forms, WPF, Windows Apps. Mobile applications can be tested on real devices or with the Android Studio Emulator or iOS Simulator and Xcode.In addition, you can test automated whether your web application complies with common accessibility standards in just a few simple steps. PDF documents can also be conveniently tested automatically with QF-Test. On the market since 2001, the test tool is continuously being actively developed and is currently used by more than 1,500 companies across 60 countries. Contact us by e-mail at service@qftest.com or get a free trial version at www.qftest.com/en!
-
Product
Development System
FE-W7
-
* Emulates Winbond W77xxx or W78xxx Microcontrollers * 125K Code Memory * Real-Time Emulation * Frequency up to fmax at 1.8V to 5.5V * Wide Supply Voltage Support * MS-Windows Debugger For C And Assembler * Emulation Headers for PLCC, QFP and DIP * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Car-to-X Signal Strength Emulator
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
Product
Channel Emulator
ACE9600
-
The dBm Advanced Channel Emulator (ACE) is the most advanced non-terrestrial RF channel emulation solution to date. The emulated impairments include delay, signal Doppler, attenuation, phase offset, AWGN, frequency hopping, payload and multipath fading. The instrument can house up to four 600 MHz instantaneous bandwidth channels.
-
Product
Advanced Network Emulators
Netropy
-
Netropy advanced network emulators simulate up to 15 separate WAN links, each with their own bandwidth, delay, and loss characteristics, through each pair of physical ports. Packets can be assigned to individual links by IP address range, VLAN, or any other packet specifier.
-
Product
Development System
FE-51MX
-
* Emulates Philips P8xC51MA/B/C , P89C669 Microcontrollers * 1MByte Code Memory * Based on bond-out Technology * Frequency up to 24MHz 3V / 5V Operation * Huge Real Time Trace Memory * Windows Debugger for C/C++ and Assembler * Target Board Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
Flight Processor Emulator
-
Flight Processor Emulators are an essential part of satellite simulators – both for testing of flight software and at the heart of operational simulators. The Terma Emulator is a suite of instruction-level emulators, based in the ESOC Emulator Suite, supporting several processors used in the Space industry: MIL-STD-1750 in both A and B variants. ERC32 in both 3-chips configuration (691-E) and single chip configuration (695-F). LEON 2 (AT-697)...
-
Product
48-CH DIO & Timer/Counter Cards
cPCI-7248/7249R
Counter/Timer Module
- PICMG 2.0 Rev 2.1- 48-CH digital TTL/DTL input/output- Emulates 4/2/1 industry standard 8255 PPI (mode 0)- Direct interface with OPTO-22 compatible I/O modules Output port status read back- On board 8254 timer/counter chip
-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
test
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Product
Power Management Analyzer Test Suites for 802.3at, 802.3bt, & Hybrid PSEs
-
While most PSE ports are part of multi-port PSE, behaviors of such systems of PSE ports are beyond the scope of IEEE 802.3 specifications. Sifos offers two fully automated analyzer suites that uniquely characterize PSE port administration and power management behaviors including PD admittance policies, PSE capacity management, LLDP policies, and powering stability. Each of these suites are built upon Live PD Emulation, a feature that enables each test port to independently and continuously emulate user-described PD’s.
-
Product
Protocol Emulations
-
Message automation and protocol simulation test tool that supports simulation of a variety of protocols (VoIP/IP, TDM, Analog, Wireless) all within a single framework. The application includes various test plans and test cases to support the testing of real-time entities
-
Product
Emulator
-
Is an advanced on-chip debugging emulator and flash programmer developed with the concept of greater efficiency in development. The combination of its high-speed downloading and various software and hardware solutions will contribute to reducing development times.
-
Product
Emulator
GCI E84
-
The GCI E84 Emulator is the world's leading tester for development, implementation and qualification of products that must comply with the SEMI E84 Standard. It provides the industry-standard automated test plans that are utilized by virtually every 300mm FAB and equipment manufacturer worldwide. GCI testers are the only solutions that guarantee 300mm factory automation interoperability.
-
Product
In-Circuit Emulator
DS-251
-
# Real-Time and Transparent In-Circuit Emulator for 251s# Uses Intel and Atmel Licensed Bondout Technology# Standard 256K Emulation Memory# Real-Time Trace up to 128K Frames Deep, 128 Bits Wide# Complex Hardware Breakpoints# Supports Both Binary Mode and Source Mode# MS-Windows Debugger# High-Level Support for Popular C-Compilers# Full Support of Local and Global Variables# On-Line Assembler and Disassembler# Performance Analyzer
-
Product
Design & Test Software
-
Industry-Leading Design, Emulation, and Test Software.Harness the power of digital twins, artificial intelligence, and automation to streamline workflows, break down silos, and accelerate test cycles.Find out why so many innovators trust Keysight to build their next breakthrough. With software spanning electronic design automation (EDA), instrument control, emulators, IT operations, and application delivery, your next project's only limitation is what you dare to dream.
-
Product
and EET200E - Encoder Emulator Tester
EET-200
-
End the shotgun approach to troubleshooting and reduce the time spent diagnosing altitude encoder/transponder problems. TRANS-CAL INDUSTRIES' EET-200 and EET-200E offers the avionics technician an inexpensive diagnostic tool for altitude encoder/transponder troubleshooting.
-
Product
PathWave BenchVue Advanced Battery Test And Emulation Software For A Single Instrument
BV9211B
-
Achieve higher accuracy, repeatability, and safety with an emulation based on a unique battery model. Your model will allow you to determine your device's power consumption, emulate an actual battery, and import existing battery models.
-
Product
Virtual tester
-
Emulate tester patterns in simulation environment with DUT simulation model. The simulation allows pre-silicon debug of test programs. Reads the actual ATE program and creates a Verilog /VHDL simulation test bench.
