Gages
See Also: Gauges, Pressure Gauges, Height Gauges, Pressure Gages
-
Product
RF Wideband Downconverter Solution From 100 KHz To 27 GHz
DC27G100
-
GaGe wideband downconverters are wide frequency coverage receivers that feature a single RF input and 3 standard software selectable IF bandwidths, from 10 MHz to 100 MHz, or 3 optional software selectable IF bandwidths, from10 MHz to 160 MHz. The carrier center frequencies can be tuned from 50 MHz to 27 GHz, using direct digitization below 50 MHz.
-
Product
General Purpose Reaction Dual Shaft Torque Sensor
STS SERIES
-
The STS Series is our general purpose reaction type shaft torque sensor. They are often installed between devices such as motors, switches, shafts or axles, and their mounting plate to provide bi-directional torque output. They are available in six capacity ranges from 600 in-lb through 12,000 in-lb, and are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
EHC-03 Basic Corrosion Thickness Gages
EHC-03
-
Danatronics is pleased to welcome our EHC-03 to our corrosion thickness gage family. The EHC-03 is designed to accurately and non-destructively measure metal structures subject to corrosion.
-
Product
Transducers, Cables, Couplants & Test Blocks
-
Olympus offers a complete selection of transducers, cables, couplants, calibration test blocks, and accessories to meet a wide variety of ultrasonic precision thickness gaging applications.
-
Product
Rosette Strain Gauges
-
Rosette Strain Gages have three measuring grids arranged at an angle of 0°/45°/90° or 0°/60°/120°
-
Product
Hall Effect Thickness Gage
Magna-Mike 8600
-
The Magna-Mike® 8600 is a portable thickness gage that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
Product
T-Rosette Strain Gauges
-
Tee Rosette Strain Gages are for measuring orthogonal strains when the principle directions of stress are known. All patterns have two grids oriented at 0° and 90° angles.
-
Product
sbRIO-9219, Non-Enclosed, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
781027-01
-
Non-Enclosed, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The sbRIO‑9219 is designed for multipurpose testing. With the sbRIO‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel. Non-enclosed modules are designed for OEM applications.
-
Product
Miniature S-Beam Load Cell
500 Series
-
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
Product
Solid Plastic Stationary Gage
200/300
-
Dwyer solid plastic stationary gages - or draft gages - are offered in inclined and vertical (well-type) styles for highly accurate laboratory or general industrial service, for measurement of low range gas and air pressures, positive, negative or differential.
-
Product
DMS Transmitter
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitter for load cells and the evaluation of strain gages in 6 mm housing with calibrated range selection.Detection signals from sensors for physical variables such as displacement, angle, pressure or force. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
Product
SURFACE PROFILE GAGES
-
Steel is often abrasive blast cleaned or otherwise roughened prior to painting. The peak-to-valley height of the resultant surface profile is an important factor in the performance of applied protective coatings. Low profile may reduce coating bond strength (adhesion). Too high and the peaks may receive insufficient coverage and possibly rust prematurely. The costly application of more coating may be required if the profile is too high. For these reasons, surface profile should be measured prior to coating application to ensure that it meets contract specifications.
-
Product
Linear Strain Gauges
-
Linear Pattern Strain Gages are the most straightforward geometry of strain gauge, designed to indicate strain in only a single direction.
-
Product
Fuel Injection Pressure Tester with 2 Gages
33950
-
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Test all Ford vehicles with multi-port fuel injection systems.Includes two gages: Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR).
-
Product
Precision Line Gage
PLG100
-
The PLG100 Precision Line Gage system is specially designed for desktop use in order to measure conductor line widths, conductor line spaces, arcs, circles and other patterns on the PCB. It can measure a conductor line width less than 1 mil. The PLG100 system is unbelievably light weighing only 0.73 kg and providing easy mobility
-
Product
Multi-Channel Telemetry
-
The AT7000 multi-channel systems can combine any customized mix of ordinary sensors: strain gages, thermocouples, RTDs, accelerometers, as well as motor/generator field voltages, currents and ground fault currents. The received data is continuously streamed to the user as analog (+/- 10V or 4/20mA) or digital data.
-
Product
Digital Signal Processing
-
Digital signal processing routines can be conducted on raw signal data acquired by GaGe high-speed digitizers either directly on the onboard FPGA of the digitizer card via our eXpert FPGA firmware features or can be optionally conducted on GPU cards receiving real-time streaming of raw signal data acquired by GaGe high-speed digitizers via the PCIe interface.
-
Product
Fuel Injection Pressure Tester
33900
-
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
Product
Data Acquisition Conditioner
D4
-
The Model D4 Data Acquisition Conditioner is a portable, USB-powered precision instrument for use with resistive strain gages and strain gage-based transducers.
-
Product
Junction Boxes
-
VPG Transducers created one of the largest load cell and transducer manufacturers in the world when we brought decades of weighing and force measurement experience under one roof. By harnessing the power of our collective expertise and experience in advanced strain gage technology, we are able to continuously challenge the status quo. As trusted partners, we are committed to providing world-class solutions that meet your needs.
-
Product
Strain & Stress Testing
-
DATASYST Engineering & Testing Services, Inc.
Using strain gaging and analysis, Datasyst can assist you in quantifying strains so you can improve your product design.
-
Product
Sensor Products: Weld Force Gage
90061
-
Model 90061 is a self-contained, portable measurement system which allows auditing of the pinch force generated between the electrodes of resistance spot welders. Resistance welding uses a pair of electrodes to clamp two base metals firmly together prior to and during application of electrical current. Poorly clamped parts result in a defective joint. A correctly clamped assembly aids in reducing the resistance in the joint and allows the current flow to properly heat the base metals to weld the part.
-
Product
NI-9236, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
779994-02
-
10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 V rms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
Product
Bore Gages - Dial
-
Measure internal diameters and bores and are a proper choice when ovality and/or cylindricity is of concern.
-
Product
12 Bit, 2 Channels 3 GS/s PCI Express Gen-3 Digitizer Up To 8 GB Memory
EON Express / CompuScope 123G2
-
The new ultra high-speed, high-resolution Gage digitizers series EON Express CompuScope offers sampling of 3 GS/s at two channels on a single slot PCI Express card and are available with various on-board memory depths from 2 GS to 8 GS
-
Product
Coating Thickness Meter
TOP-CHECK
-
The TOP-CHECK coating thickness gauges from List-Magnetik feature a unique 90° pivotable probe that allows you to make accurate coating thickness measurements every time. These compact, lightweight gages are barely larger than a probe, making them ideal for field applications in hard-to-reach areas.
-
Product
ECHO 8 Ultrasonic Corrosion and Precision Thickness Gage
ECHO 8
-
Danatronics offers our newest ultrasonic precision thickness gage line, the ECHO 8 series. ECHO 8 represents our most advanced thickness gage ever combining dual and single element transducers all in one small package. ECHO 8 offers a 3.5” high resolution sunlight readable color display with live A-Scan, use of a wide variety of dual, contact, delay line and immersion transducers from 1-20 Mhz as default and custom created and stored applications setups, B-Scan, datalogger with up to 32GB of SD card memory and interface to Microsoft excel. The ECHO 8 is available in 4 models including the ECHO 8, ECHO 8DL, ECHO 8W and ECHO 8DLW. The vibrate on alarm feature is the world’s first and is great for loud environments
-
Product
PCIe Octave Express 14-Bit Digitizer
-
The GaGe Octave Express 83XX CompuScope PCIe digitizer card features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11.1-bits with 10 MHz input.
-
Product
Torque Sensors
-
In universities and industry, for basic research or quality assurance: Kistler torque sensors guarantee precise definition of the power and friction values of drives, transmissions and pumps. Strain gage technology (DMS) is a powerful solution for measurements on rotating shafts, and also for long-term dynamic and static measurements. Maximum precision, the most rigid structure possible and high temperature stability: thanks to these assets, DMS sensors can accomplish the most demanding tasks. Piezoelectric reaction torque sensors offer convincing features such as exceptional overload protection, high signal resolution and a wide frequency range. They are ideal for measurement tasks when conditions are difficult due to geometry, temperature range or dynamics.
-
Product
Signature Compression Only Load Button Load Cells
SLB SERIES
-
The SLB Series Subminiature load cells (Load Buttons) are offered for compression only applications where space is limited. The matching surface must be flat for ultimate accuracy. The loading diameter is slightly convex for accurate load distribution. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
