-
Product
*Laser Power & Energy Meters
-
Ophir laser power meters work on the smart plug principle. This means that almost any Ophir power meter can work – plug and play – with almost any of the wide range of Ophir sensors. Ophir power meters are also the most precisely calibrated units on the market thus measuring with the highest accuracy. Noted for their versatility, ease of use, and user friendly interface, Ophir meters can be used stand-alone or interfaced with LabVIEW or the user's own software.
-
Product
X-ray Fluorescence Sulfur/Chlorine-in-oil Analyzer
MESA-7220V2
-
The MESA-7220V2 measures both sulfur and chlorine in petroleum based products using the Monochromatic Energy Dispersive X-ray Fluorescence (EDXRF) method. A monochromatic X-ray source is used in order to obtain an ultra-low noise background which affords the best detection limits for both sulfur and chlorine.The detector window size was increased to collect more fluorescent X-rays and thus achieve lower level ppm values. This provides excellent, repeatable performance at both low and high concentrations of both elements.By adjusting the angle of the graphite crystal, the excitation beam can be measured to excite sulfur in the sample, increasing sensitivity.
-
Product
Technological Solution
Ducknet
-
The Duck Net system is the technological solution by Ducati Energia to create an energy management and monitoring system compliant with the standards ISO50001, ISO14001, ISO50001, directive 2012/27/UE, Italian law DL 4-7-2014 n. 102
-
Product
Battery Testing
-
Electric vehicles (EVs) rely on batteries as their primary source of energy storage. As battery packs require battery management systems (BMS) to operate safely and reliably, it is vital to test control algorithms for state of charge (SoC) estimation or cell balancing at an early stage.
-
Product
Structural Load Monitoring
SLM
-
Since 2001 ITM has installed structural strain based monitoring systems in the pulp & paper and energy generation industries. For these systems, our engineers and field service technicians turn structures into measurement instruments (load cells). Load outputs from the structural load cells are monitored and published by a realtime controller to its local interface or network historians and HMIs.
-
Product
elemental analyzer
SPECTRO XEPOS
-
SPECTRO Analytical Instruments GmbH
An elemental analyzer designed for demanding applications – the SPECTRO XEPOS energy dispersive X-ray fluorescence (ED-XRF) spectrometer redefines XRF analysis with exceptional new levels of performance
-
Product
Power Performance Test
-
The performance index of power product is decide the product quality, so it is very important to accurately test performance index in every stage to make sure that the product performance is conform to design index. Energy efficiency index includes power factor, input power, input voltage and etc.
-
Product
Environmental Control Systems
-
We are committed to developing eco-friendly technologies that reduce energy use and emissions without affecting flavor or aroma. Our equipment features thermal and catalytic exhaust air-cleaning systems and process-integrated energy recovery systems to ensure efficient, compliant operations.
-
Product
Computrac® MAX®
4000XL
-
The Computrac MAX® 4000XL provides quick, reliable and accurate results. This improves the ability to adjust or monitor processes, ensuring quality products while minimizing waste, energy requirements and man-hours. Ease of use and durability, along with superior service and support make the Computrac® MAX® 4000XL an ideal choice for research, manufacturing and laboratory environments.
-
Product
Telemetry Systems
-
For Automotive, Aerospace, Marine, Motor & Generator Health, Energy, Power Plant, and Industrial Applications.
-
Product
Coercive Force Meter
-
The meter is mainly used in measuring the coercive force of magnetic components of relays and the mechanical energy meter compensation films, which is the essential instrument of manufacturers who are producing the relays and the energy meters, etc.
-
Product
Electrical Circuit Protection - Breakers
-
Eaton’s complete line up of low and medium voltage circuit breakers and fuses are used to provide circuit protection in alternative energy, commercial, industrial, mining, and military applications, where they protect against overloads and short circuits in conductors. These circuit breakers are applied in panelboards, switchboards, motor control centers, control panels, combination starters, individual enclosures, and bus duct plug-in units.
-
Product
DC Energy Meter
-
Multiple channels can be measured by a single meter, EN2450N & EN2450D. Differential current input for all the current channels. Programmable shunt secondary 50mV to 100mV. Programmable CT Primary for all channels up to 200A - for Hall Effect CT. Data logging for parameters such as Energy, Load hours and Ampere hours. Easy installation,Compact size, weight and simple wiring.
-
Product
Short Range
-
A standard-compliant wireless technology, optimized to fit short range connectivity, energy per bit and bandwidth requirements, is behind every network - regardless of its nature or purpose. With the growing importance of wireless sensor networks and the IoT, most electronic systems require wireless connectivity.
-
Product
Portable Three Phas Multifunction Electric Meter Calibrator
GF312V2
-
Beijing GFUVE Electronics Co.,Ltd.
GF312V2 portable three phase multifunction energy meter calibrator is with comfort design, small size, and light weight. It is suit for electric power departments, measuring and quality examining departments and electric lab to field use.
-
Product
Analysis System
Neptune (EDS-WDS)
-
By integrating Energy Dispersive Spectroscopy (EDS) and Wavelength Dispersive Spectrometry (WDS) analytical techniques on a single platform, Neptune provides the power and flexibility of EDS with the resolution, precision, and detection limits of WDS. Together the two techniques extend X-ray microanalysis capabilities and provide solutions to the most challenging analysis problems. Each technique can be used independently or the data can be integrated to provide results which were previously unachievable.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel With V/I Readback
41-752A-011
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Energy & Process Monitor
-
Real time monitoring and reportingComposite system with EMS and PEMSDesired reports like, Doff wise, shift wise, count wise, production, energy, UKGSpeed Vs Kw curve, trends, bar graphs, comparisonsAlerts on higher UKG, lesser production, utilization & power fluctuations.Maintenance alerts based on run hours production cost analysis - Cost Audits - Energy Audits
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 KV Isolation
41-752A-101
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture. The 750 V or 1 kV isolation barrier (version dependent) allows the module to be used as a lower power version of a battery stack, representative of those used for vehicle propulsion.
-
Product
Dielectric Loss Tangent Testing Instruments
-
Insulation materials in electrical equipment are used between a pair of electrodes; therefore it can be expressed as capacitors. Applying AC voltage to a capacitor with insulation materials causes an energy loss due to the leak current, the dielectric polarization, and the partial discharge. Because of this, the phase of the capacitor current is more delayed than that of a zero-loss current (reactive current) flowing in an ideal insulation material. The delay angle is called "Dielectric Loss Angle", and the tangent is "Dielectric Loss Tangent" (tanδ). Please refer to the technical guide explained in detail.
-
Product
Multi Function Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
Live circuit warning LED:Immediate illumination of a warning lamp if the circuit under test is live Auto Discharge:Allows fast and safe discharge of electrical energy stored in capacitive circuits following testing Integral overload protection on internal continuity and insulation test circuitry Autoranging 500V DC test voltage for insulation tests 200mA short circuit current on continuity ranges Loop and RCD Testing Wiring connection check LED''s:Immediate indication if wiring of circuit under test is correct Overheat Protection:Rapid detection of overheating of internal circuitry,display of warning signal to user and automatic halting of measurement Supply Voltage Indication:Can display supply voltage value in loop impedance mode Low Current Loop Impedance Test:Short duration low test current will prevent tripping of many passive RCDs
-
Product
Nuclear Safeguard Systems
-
Nuclear Safeguards are measures to verify that States comply with their international obligations not to use nuclear materials (plutonium, uranium and thorium) for nuclear explosives purposes. Global recognition of the need for such verification is reflected in the requirements of the Treaty on the Non-Proliferation of Nuclear Weapons (NPT) for the application of safeguards by the International Atomic Energy Agency (IAEA). Also, the Treaty Establishing the European Atomic Energy Community (the Euratom Treaty) includes requirements for the application of safeguards by the European Commission. Organizations such as the IAEA and EURATOM and others are tasked with ensuring declared amounts of material are indeed present in the facilities in which they are stored and that such material is not being diverted to other uses.
-
Product
Circulators
-
The most common application of a circulator is as a duplexer, allowing the transmitter and receiver in a radio or radar unit to share a common antenna. Energy is transferred from the RF Source to the antenna during transmit, and from the antenna to the receiver during the receive cycle. In each case the circulator functions to isolate the inactive port from the propagated signal. Most importantly, the transmitter output is not passed to the receiver input, preventing the high transmitter power from damaging the sensitive receiver input circuits.
-
Product
Energy Efficiency Testing
-
Intertek has the requisite accreditations, expertise and state-of-the-art testing laboratories around the world to help you meet energy efficiency requirements for global markets. Improving energy performance, developing clean and sustainable energy, and protecting the environment are key initiatives that all manufacturers must undertake if they wish to compete in today’s socially-conscious markets.
-
Product
Control Software
AsTest
-
AsTest control software is designed to enable the calibration and verification of energy meters on the ASTeL meter test equipment. Built-in features permit efficient service of various types of meters, as well as advanced data management. The parametrical libraries within AsTest software minimize the need to create new definitions. Assorted data visualizations provide notification of current system events on an ongoing basis. Intuitive graphic design and user friendly visualization of the testing processes makes working with AsTest control software straightforward.
-
Product
Thermopile Laser Power Measuring Heads
BB Series
-
The BB series of heads has a black broadband absorbing coating. The HP series is equipped with a ceramic layer which allows for high energy and power densities.
-
Product
1-phase Power Analyzers
-
PeakTech Prüf- und Messtechnik GmbH
Is a high-precision energy cost measuring device for recording the energy consumption of electrical devices and for calculating the current consumption of a device by entering the electricity price. Thanks to the integrated power factor calculation, all modern consumers such as Switching power supplies, TV sets, fluorescent lamps, LED systems and of course ohmic loads such as Electric heaters and hobs can be measured accurately. In addition, the high resolution, the low response characteristic and even very small or stand-by consumers from approx. 1 W can be measured.
-
Product
RL78 Family Of 8/16-bit Ultra-Low Energy MCUs
-
RL78 microcontrollers greatly improve power efficiency with industry-leading low power consumption at 45.5 μA/MHz consumption during normal operation and 0.57 μA/MHz during clock operation. Built-in features such as a high-precision (±1%) high-speed on-chip oscillator, background operation data flash capable of 1 million rewrites, temperature sensor, and interface ports for multiple power supplies help reduce system costs and size.
-
Product
Automatic Relay Test Set
DRTS 34
-
DRTS 34 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 4 Voltage generators simultaneously available.
-
Product
Panel for Energy Monitoring
Energy Box
-
The box allows a quick installation of the energy monitoring and remote control system Ducknet
