Pulsed Laser Diode Drivers
See Also: Laser Diode
-
Product
Half, Full Bridge & Three Phase Drivers
-
Renesas' half-bridge (h-bridge), full-bridge and three-phase drivers handle voltages up to 100V, with industry-leading gate rise and fall times and exceptional input-to-output propagation delay performance.
-
Product
Laser Thermal Power Sensors
-
Thermal sensors have a series of bimetallic junctions called a thermopile. Radial or axial heat flow through the sensor creates a voltage proportional to the power absorbed as it flows through the thermopile. The reading is not dependent on the ambient temperature since only the temperature difference is measured and not the absolute temperature. The thermopile elements are so arranged that the reading is almost independent of beam size and position. Generally, Ophir specifies ±2% or better uniformity of reading over the surface.
-
Product
Analog Laser Power Probes
-
Laser power measurements should be quick and easy. They should not involve time consuming set-up and alignment problems. Ideally, the measurements should also be able to be made at any point in an optical system where losses are likely to occur. Unfortunately, most laser power meters have sacrificed ease of use to gain continuous power readings.
-
Product
Pulse AC Method Area Ionizers
ER-X Series
-
Panasonic Industrial Devices Sales Company of America
The ER-X Series Area Ionizers utilize the pulse AC ionization design to achieve high-speed charge removal of wide surface areas for high-volume production lines. In addition to supporting compressed air ionization, the ER-X also features both airless and low-pressure ionization modes for applications where tiny workpieces can be easily blown away. Additional features include automatic ion balance and discharge frequency control (manual control is also possible), flat discharge surface for easy cleaning, discharge needle air barrier design to reduce contamination of the needles, replaceable discharge needle unit for easy maintenance, and a dual head configuration for enhanced charge area and layout (2 different ionizer heads can be connected to a single controller).
-
Product
Laser Distance Meters
-
Sends a pulse of laser light to the target and measures the time it takes for the reflection to return
-
Product
Serial Controlled Relays And Relay Drivers
-
*ICS's Serial controlled Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the Serial to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are IEEE-488.2 compliant and use SCPI commands for operation with NI or Agilent VISA, LabVIEW and VEE or any Serial programming language. Use ICS's interactive Serial Keyboard program for easy operation from your PC without having to write a program.
-
Product
Tunable Diode Laser Absorption Spectroscopy
5100 TDLAS
-
The feature-rich 5100 TDLAS offers high-sensitivity, analyte-specific, fast-response measurements for critical industrial applications. It features a single absorption cell and integrated sample system in a compact, cost-effective package.
-
Product
Pulsed and CW lasers, 375 – 1700 nm, 1 kHz measurement rate
871 Series
-
The 871 Laser Wavelength Meter from Bristol Instruments is the best way to measure the absolute wavelength of both pulsed and CW lasers and OPOs. By combining proven Fizeau etalon technology with automatic calibration, the reliable accuracy needed for the most meaningful experimental results is ensured. What’s more, a sustained measurement rate of 1 kHz enables the wavelength characterization of every single pulse for most lasers. And, the resulting time resolution of 1 ms provides the most detailed analysis of tunable lasers.
-
Product
Picosecond Laser
PIXEA
-
The PIXEA is a high-quality laser system for OEM and R&D applications generating ultra-short optical pulses by using gain-switched laser diode technologies. The laser features high-quality picosecond laser pulses with no satellite pulses and minimize pulse tail. The PIXEA series offer a large variety of centered wavelengths between 375 nm and 2 um. The pulse duration down to 20 ps is optimized for each wavelength. The system is based in two modules or one module, the laser head and the dedicated Control Unit including the GUI software. Different optical output options are available, including free space collimating optics and fiber coupled.
-
Product
Laser Power And Energy Meters
-
Measure laser power and energy with ease and precision over a huge range of wavelengths, power levels, and pulse energies.
-
Product
Laser Measurement Instruments
-
Wide-ranging line of laser power and energy measurement products that deliver accurate, ISO/IEC 17025 certified measurements, and laser beam diagnostics systems that measure spatial intensity distribution and beam size. All backed by more than 50 years of industry experience, with worldwide service and support.
-
Product
Phasecam Twyman-Green Laser Interferometers
-
PhaseCam dynamic Twyman-Green laser interferometers provide high resolution measurements despite vibration and air turbulence. Dynamic Interferometry® enables PhaseCam laser interferometers to capture full wavefront measurements in as little as 30 microseconds—5000 times faster than conventional phase shifting interferometers. Compact and lightweight, PhaseCams make reconfiguring test setups simple and easy, without vibration isolation.
-
Product
Laser power meter
LM 100
-
This read out unit is designed to measure the output power of different lasers in combination with a thermophile head. The maximum power is limited by the power head used. Normally, the time constant of a power head is in the region of 15 to 25 seconds. Use of the read out unit enables reduction of the time constant of the whole measurement system to one second.?
-
-
Product
Pulsed High Field Magnetometer
TPM
-
This is the equipment evaluating the magnetic properties of rare-earth such as Js, Jr, Hcb, Hcj, (BH)max, HK and SR etc.
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
Laser Diode Burn-in Reliability Test System
58604
Test System
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
Product
Diode Lasers
Spot Creator
-
Advanced Photonic Sciences LLC
Spot Creator is an innovative accessory developed for enhancing the performance of blue laser diode based engraving and cutting machines. Spot Creator solves a major problem with using asymmetric blue laser diodes: the production of engraving features that are different in the X-Y directions, resulting in unequal or blurred lines. Using Spot Creator, line widths are equal in the X-Y directions, with a minimum spot of 50 μm. The intensity on the engraved part is thus maximized.
-
Product
THz Diodes
-
Macom Technology Solutions Holdings Inc.
The intrinsic cutoff frequencies of these Schottky junction devices exceed 1 THz, making them well-suited for use in mixers and detectors operating in the frequency bands from 60 GHz into the hundreds of GHz bands.
-
Product
Pulse Oximeter Simulators
-
Take control of all your simulations with the next-generation SpO2 pulse oximeter simulator, OxSim Flex. The world’s smallest SpO2 tester now provides complete flexibility in selecting saturation, pulse rate and perfusion index. Users can create customized Preset Simulations for faster testing of oximeter performance and for alarm testing without having to change the monitor’s alarm settings!
-
Product
Silicon Diodes
DT-670 Series
-
DT-670 Series silicon diodes offer better accuracy over a wider temperature range than any previously marketed silicon diodes. Conforming to the Curve DT-670 standard voltage versus temperature response curve, sensors within the DT-670 series are interchangeable and, for many applications, do not require individual calibration. DT-670 sensors in the SD package are available in four tolerance bands—three for general cryogenic use across the 1.4 K to 500 K temperature range and one that offers superior accuracy for applications from 30 K to room temperature. DT-670 sensors also come in a seventh tolerance band, B and E, which are available only as bare die. For applications requiring greater accuracy, DT-670-SD diodes are available with calibration across the full 1.4 K to 500 K temperature range.
-
Product
Laser Diode Light Current Voltage (LIV) Test Instruments
-
The Yelo LIV test instrument allows LIV measurements to be taken from laser devices loaded into a Yelo module. This module can also be used with the Yelo Y1000L Low Power Burn-in system. The LIV test instrument has been designed for easy operation. Once powered on, and with laser supply enabled, the touch screen can be used to initiate, monitor and review measurements of laser devices.
-
Product
Picosecond Lasers
PL2230 Series
-
The first commercial fully diode pumped high pulse energy mode-locked laser, producing 28 ps pulses with up to 140 mJ pulse energy.
-
Product
Multi-Axis Laser Interferometer
-
The award-winning XD Laser is a multidimensional laser measurement system that simultaneously measures all 21 degrees of freedom including linear, angular, straightness and roll errors for rapid machine tool error assessment. Measurements Include:- Rotational accuracy- Geometric error- Angular error- Flatness- Squareness- Parallelism
-
Product
Laser Tachometer
LaserTach™
-
The LaserTach™ ICP™ tachometer senses the speed of rotating equipment and outputs an analog voltage signal for referencing vibration signals to shaft speed. The sensor allows for measurements in excess of 30,000 RPM from distances as far as 20 inches (51 cm).
-
Product
Stepper Motor Drivers
-
Minimize noise and vibration in your stepper motor designs with our QuietStepTM adaptive stepper motor drivers. We offer a complete lineup of stepper motor drivers for office automation, industrial, and automotive applications. Our advanced QuietStepTM solutions use proprietary algorithms to reduce torque ripple and current distortion. To minimize ripple current for the various operating conditions, QuietStepTM adaptive stepper motor drivers perform on-the-fly adjustments to the amount of fast decay during a pulse-width modulation (PWM) cycle. This adaptive feature improves system performance, reduces audible motor noise and vibration, and increases step accuracy.
-
Product
Pulse Width Extender
TLP-3011C
-
High Power Pulse Instruments GmbH
*Fully automatic pulsewidth extender*Pulse width up to 1.6 µs in 68 programmable steps of 25 ns*Ultra fast 50 Ω pulsewidth extension with typical 100 ps rise time*High pulse output current up to ±40 A*High performance and high quality components
-
Product
High Power Fiber Laser
-
Amonics' Fiber Laser (AFL) is a compact standalone turnkey equipment to deliver up to 50W output power and 1mJ pulse energy in 1064nm and 1550nm range under CW or pulse operation. Based on proprietary all fiber design, Amonics fiber laser is maintenance free. No post-installation service is required.In pulse operation, the laser delivers up to 20kW peak power and adjustable pulse width from 10ns to 1000ns. The pulse repetition rate is triggered by external TTL signal.Amonics fiber lasers are the ideal candidate for a wide range of industrial applications.
-
Product
Industrial 4-20mA Driver
-
Analog Devices portfolio of leading industrial d/a converters and drivers addresses the challenges of enhancing system accuracy, reliability, and overall functionality while reducing form factor and power dissipation. The products provide a range of programmable output ranges from standard 4–20 mA for current loop communication to ±10 V for actuator control. They simplify industrial system design by offering considerable control functionality and advanced on-chip diagnostics to maximize system up time. ADI industrial converters also eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
Product
Laser Microgage
2D
-
The Microgage 2D laser alignment tool can be adapted to a wide variety of industrial measuring and alignment requirements. Each receiver measures in two axial directions (X & Y) and can be used for checking straightness, flatness, parallelism, squareness, bores, spindles, and other alignment needs.
