-
product
Development Platform
NFC/WLC
CISC is offering various technology elements to support the design of NFC-based WLC (wireless charging). These pre-tested hardware modules including various antenna sizes, firmware, and software support customers to quickly have available solutions for their requirements. Customization helps in particular for very challenging application requirements. Customers benefit from very fast time to market for WLC solutions.
-
product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
product
1.8-148 MHz Stand Alone Weatherproof Unit for the Application of DC Control Signals up to 400ma on your Coax Cable
Bias-T PLUS
The Array Solutions Bias-T PLUS is a 1.8-148 MHz stand alone weatherproof unit that permits the application of DC control signals of up to 400ma on your coax cable. By inserting the control voltage on the coax cable feed-line, you eliminate the requirement for external DC wires for powering remote devices.The Bias-T PLUS weatherproof assembly means that it can be placed indoors or outdoors for maximum flexibility. Typically, one Bias-T PLUS will be placed indoors for inserting DC on your coax feed-line, and one Bias-T PLUS will be placed at the remote device where the DC voltage is extracted.
-
product
Software for Test, Analysis and Simulation applications
AIM Software Solutions
AIM offers PBA.pro Software for Test, Analysis and Simulation applications. PBA.pro is compatible with Windows and LINUX Operating Systems and supports most of the AIM interface hardware modules. The flexible, scalable and open PBA.pro concept supports a wide spectrum of customer applications.
-
product
Test Requirement Document for Developing and Documenting Strategy and Structure of Test Programs
TRD System
The TRD System helps users develop and document the strategy and structure of test programs using TRD format screens, flowchart generation tools and documentation formats, all in accordance with the most popular military standard format ( MIL-STD-1519) or with unique custom formats. It also has the ability to automatically generate an ATLAS test program from the TRD information provided by the user.
-
product
The Cyberbit Skill Development Platform
Cyberbit is the only platform that delivers the entire cyber skilling spectrum, on-demand, in coherent learning paths, validating your team’s performance and progress along the way.
-
product
Desktop Application
Desktop application testing refers to the testing of standalone software that can perform without a network, on a desktop, or on a laptop. Desktop applications are not affected by network downtime.
-
product
Stackable And Configurable Signal Generator For CAN Applications.
K- Volt
The K-Volt can be used to generate fast configurable analog and digital signals from CAN messages. Designed for high speed and accurate simulation of sensors (For example HIL and Replay systems). The K-Volt can be connected directly to a PC via a USB connection.
-
product
ARINC 429 Simulator & Analyzer Applications Software
F-SIM-A429
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 429 InterfacesCapture & Analyze Data from Multiple ARINC 429 Input ChannelsDefine & Execute Complex Simulations of Multiple Rate-Oriented Labels - Simulate Output Data on Multiple Channels Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Update, Modify, & View ARINC 429 Data on-the-fly - Engineering Unit Displays & Software Widgets - Receive Data to Label/SDI Specific Buffers - Also Supports MIL-STD-1553, ARINC 664, Ethernet, & Data Load operations
-
product
Fluke DAQ 6.0 Application Software
Fluke DAQ 6.0 is a powerful, versatile data acquisition application that provides effortless configuration, data logging, and analysis for the 2680A and 2645A NetDAQ Networked Data Acquisition Unit » and 2680 Series Data Acquisition Systems », plus adds support for the Fluke 2638A Hydra Series III Data Acquisition System/Digital Multimeter » and Fluke Calibration 1586A Super-DAQ Precision Temperature Scanner ».
-
product
Microprocessor Development System
DS-M8
# Real-Time and Transparent In-Circuit Emulator# Supports PIC12xxx, PIC14xxx, PIC16xxx, PIC17xxx and others# Uses Microchip Bond-Out Technology# Maximum Frequency Support# Standard 64Kx16 Emulation Memory# 32Kx48 Real-time Trace with Filters and Triggers# 64K Hardware Breakpoints with External Signals# Memory Mapping Capabilities# Software for MS-Windows# Source-Level Debugger for C and Assembler
-
product
Silicon Nails Feature Development And Runtime, GTE 10.00p
K8228B
The Silicon Nails test development tool also allows users to define the vectors that they would like to execute on the non-compliant boundary scan device. The test development tool will generate the boundary scan test to output or input at the relevant interconnecting pin, thus generating the test consistently.
-
product
Development System
FE-5131
Emulates AT89C5131/AT89C5131A Derivatives with 6/12 Clocks/Cycle31K Code MemorySoftware TraceReal-Time EmulationFrequency up to 40MHzMS-Windows Debugger for C and AssemblerKeil Vision2 Debugger CompatiblePLCC, SOIC, QFP and 32-QFN Emulation HeadersSerially Linked to PC at 115Kbaud
-
product
LabVIEW Communications Application Frameworks
The Application Frameworks are software reference designs that provide a rich set of high performance FPGA IP for prototyping real-time wireless communication systems. When combined with NI’s line of software defined radios, the Application Frameworks form a complete hardware and software prototyping platform that enables researchers to accelerate their prototyping efforts and achieve results quickly.
-
product
Custom Antenna Development
Specializing in the development of unique antennas, JEM’s antenna design experience includes: Broadband Antennas, Narrowband Antennas, Genetic Antennas, Array Antennas & Beamformers.
-
product
VPX Development System
VPX370 3U
The VPX370 is a second generation VPX development platform that delivers, performance, flexibility, and scalability all in a compact 3U VPX form factor.
-
product
Interface Module for Multimode, Multiprotocol Excalibur 8000 Family of Carrier Boards, a Complete Solution for Developing & Testing 1553 Interfaces
M8K1553Px(S)
The M8K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M8K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M8K1553PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M8K1553PxS module is NOT compatible to the M4K1553MCH module.The M8K1553Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
LabVIEW Full Development System
LabVIEW is engineering software designed specifically for test, measurement, and control applications that require rapid access to hardware and data insights. The LabVIEW Full Development System is recommended to customize your engineering application with advanced inline analysis and control algorithms. For applications that require software engineering tools to develop, debug, and deploy professional applications, consider LabVIEW Professional Development System.
-
product
MORA Ready Development Platform: CompacFrame Integrated With SOSA Aligned PICs And Sciens Innovations Helux Core RF Tools
SE9M3PS9YIBXNLY
The MORA-Ready Development Platform (MRDP) simplifies the process of creating RF signal processing capabilities and accelerates integration of existing applications. Featuring Sciens Innovations helux™ Core powerful software tools to accelerate RF signal generation and system development.
-
product
Software Communications Architecture (SCA) Development Environment
NordiaSoft products enable embedded systems developers to rapidly create software artifacts using the Component Based Development (CBD) and Model Driven Engineering (MDE) paradigms. Implementing the Software Communications Architecture (SCA), an open specification adopted internationally and evolved through the Wireless Innovation Forum (WInnF), a consortium of major radio manufacturers, academic, research laboratories and government authorities, the NordiaSoft products provide multiple advantages over other commercially available solutions for embedded systems:
-
product
MIL-STD-1553 IRIG 106 Chapter 10 Streaming Application
F-SIM-1553-CH10-STREAM
Avionics Interface Technologies
Streams MIL-STD-1553 Data from AIT MIL-STD-1553 interfaces in Chapter 10 Format - Software application which is Compatible with all AIT MIL-STD-1553 Interfaces - Capable of streaming data captured from one or multiple MIL-STD-1553 Bus Interfaces - Streamed data can be sent to a single network system or multicast on the Ethernet LAN - Compatible with AIT F-SIM-1553-AVOE analyzer or 3rd party Chapter 10 systems - Timestamps & Errors detected embedded in Chapter 10 stream
-
product
1-Slot 3U VPX Development Chassis for Quartz Products
Model 8257
- 1-slot, small footprint development chassis- Optional dual MPO interfaces support 100 GigE- Supports VITA-66.4
-
product
Application Programming Interface Software
AltaAPI
Alta’s 1553 and ARINC cards include the most advanced Application Programming Interface (API) library tools in the avionics industry, AltaAPI. The API architecture is a properly OSI modeled development package that provides an extremely flexible design to provide quick porting to various operating systems (such as VxWorks 5.X/6.X/7/MILS, Integrity, LynxOS RTOS), Linux 32- and 64-bit, Solaris 10, LabVIEW and 32- and 64-bit Windows 7/8/8.1/10.
-
product
Rapid Prototype Development
Have time to market pressure and need to get a system or assembly or production line up and running quickly? Need to rapidly build out a solution, but don’t want to spend months on building up an architecture? Allow our rapid prototyping team to assist you – whether it is crafting 3D printed mechanical assemblies or a building up a high speed IO interface, you are in very capable hands with the ARC engineering team. Our DSX product, can help support your IP, implement your process or and be the core processing engine for your design, or if a larger system, DSX could be an integral part of your system. PVS, another tool that can help error-proof your assembly process, is ready to go in a flexible, software-centric solution that you can be reconfigured as needed to meet your changing demands.
-
product
High Performance Embedded Development Kit
TySOM EDK
The TySOM™ Embedded Development Kit is for the embedded designers who need a high-performance RTL simulator/debugger for their embedded applications such as IoT, Automotive, Factory automation, UAV and Robotics. The kit includes Riviera-PRO™ Advanced Verification Platform and a TySOM development/prototyping board. TySOM boards come with either a Zynq 7000 chip (FPGA + Dual ARM® Cortex™-A9) or with a Zynq® UltraScale+™ MPSoC device. These boards include memories, and various communication and multimedia interfaces in addition to FMC connectors for peripheral expansion. Reference designs for application such as IoT, ADAS, 4K UltraHD imaging and Robotics and a complete reference design, which contains the SW (Linux) and all the hardware blocks required to support the peripherals on the board, are provided.
-
product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
product
Condenser for General Applications
PECA2
Lifasa - International Capacitors, SA
These capacitors are designed for use in circuits where they are subjected to non-sinusoidal voltages and pulsed currents, such as switching and damping circuits. They can also be used as discharge and filtering capacitors, as well as for any DC application. This capacitor is especially suitable for applications where a high life expectancy and a high RMS current are required.
-
product
Application Software
Radiant's application software packages are used in conjunction with ProMetric® Imaging Colorimeters and Photometers to provide complete solutions for accomplishing specialized testing and calibration tasks in R&D, production lines, or in the field.
-
product
Enterprise-Wide Application and Security Testing
PerfectStorm ONE
Keysight Network Applications and Security
Enterprises and government organizations are making major investments in consolidating and rebuilding data centers and enterprise -wide networks. The stakes have never been so high to get it right the first time.
-
product
Boundary Scan Program Development Service
No need for test fixtures. Integrates product development, production test, and device programming in one system. Test and Programming data can be reused in Production. Fast test procedure development. Reduced inventory management. Eliminates or reduces ICT usage time. Pre-production testing can begin as soon as prototype is released.
