Portable PXI Chassis
See Also: PXI Chassis, 3U PXI Chassis, 6U PXI Chassis
-
Product
Rack And Chassis Mount Products
-
PMI offers various RF and Microwave products that range from 250 kHz up to 40.0 GHz which are supplied in a ruggedized, 1U to 6U chassis. Many options are available.
-
Product
Portable Thickness Gauge
Magna-Mike 8600
-
The Magna-Mike® 8600 is a portable thickness gauge that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
Product
PXI 8 Slot BRIC 168x16 2A 1-Pole Matrix
40-598-107
Matrix Switch Module
The 40-598 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-598 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI Load Resistor Module 10 Ohm to 2.56k
40-292-012
Load Resistor Module
A simple solution for applications requiring a programmable load resistor with up to 15W power handling. It is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
Product
High Density Switch Matrix PXI Card
GX6616
Matrix Switch Module
The GX6616 is a 6U PXI switch matrix board that provides either differential or single-ended multiplexing capability through software commands, along with six groups of 2 x 16 that may be used in various configurations.
-
Product
PXI Solid-State SPST Switch, 6-Channel 25A 100V
40-184-001
SPST Switch
This range of PXI high power switches support 6-off high current SPST switches into two PXI slots or 3-off high current SPST switches into one PXI slot. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each PXI solid-state SPST switch can support 25A of continuous current and switch up to 100V signals. The switch can sustain inrush currents of up to 90A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI Octal 3:1 High Voltage Power MUX
40-331-005
Multiplexer Module
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
PXI 3A Power MUX BRIC, 6-Channel, 48-Pole
40-571-006
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Portable Ultrasonic Flowmeter
-
Gentos Measurement & Control Co.
As one of the most professional portable ultrasonic flowmeter manufacturers and suppliers in China, we're featured by quality products and low price. Please rest assured to buy discount portable ultrasonic flowmeter in stock here from our factory. For customized service, contact us now. Cleaning System Flowmeter, Building Management System Energy Flow Meter, Condensate Water Ultrasonic Flow Meter
-
Product
2-Slot BRIC, 256x4, 1Pole, PXI Matrix (2 Sub-cards)
40-559-201-256x4
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays. With their high level of switching density, these PXI matrices allow a complete Functional ATE system to be housed in a single 3U PXI chassis and allow the use of much lower cost 8 or 14-slot chassis. The 40-559 matrices can be used in many industries; typical applications include automotive ECU and semiconductor package testing. Dual analog busing for the narrower matrix options, enable completely separate matrices within a single module for parallel testing.
-
Product
FPGA PXI High-Performance Digital I/O Card
GX3702
Digital I/O Module
The GX3702 is a user configurable, FPGA-based, 3U PXI card which offers 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features over 45,000 logic elements and 1.836 Kb of memory. The GX3702 is supplied with an integral expansion board providing access to the FPGA's 160 I/Os and is pin for pin compatible with the NI PXI 7813R and 7811R FPGA cards . Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
Product
PXI Single 64x4 Matrix 2-Pole Switching
40-533A-022
Matrix Switch Module
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
Portable Power Analyzers
-
Portable network analyzers are essential for conducting energy audits as well as for reviewing the quality of the power supplied and the consumption in electrical installations. They provide for real-time recording and monitoring of electrical parameters, anywhere in an electrical installation, for the conduct of energy improvement studies, as well as for the detection of problems related to the quality of supply and consumption.
-
Product
Portable Particle Monitor
iCountOS
-
The iCountOS is a highly rugged portable particle size monitor that can be used for measuring contamination levels in fuels and/or hydraulic fluids. Capable of operation online (direct connection to system) or offline (sampling from tank or reservoir).
-
Product
PXI High Density MUX BRIC, 48-Chan, 20-Pole
40-570-316
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
6-slot ShoeBox Chassis
AX60501
-
*Desktop or wallmount industrial computer chassis*One 5.25" and two 3.5" HDD drive bays*Equipped with a PS/2 type power supply
-
Product
PXI 8 Slot BRIC 88x4 1-Pole (2 sub-cards)
40-562A-121-88X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 90X16 1-Pole (6 sub-cards)
40-561A-121-90X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 110x16 2-pole (10 sub-cards)
40-562A-122-110X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
787987-01
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
PXI High Density MUX BRIC, 6-Chan, 160-Pole
40-570-016
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PXI 8 Slot BRIC 232x6 2A 1-Pole Matrix
40-596-104
Matrix Switch Module
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
Chassis Rugged Slide Rail Size 5
CAE016383
-
Securely locked in extended position. The chassis/cabinet mounted slide rails are ultra rugged and hold significantly more weight and can withstand shock and vibration in harsh environments.
-
Product
Chassis Mounting Kit
63-924-001
Mounting Kit
This chassis mounting kit is designed for use with the our 8-slot PXI chassis (40-924) and our 7-slot LXI modular switching chassis (60-102D), allowing installation into a standard 19" rack.
-
Product
PXI Single SP6T Multiplexer 26.5GHz 50, SMA-2.9, Terminated
40-785B-531-T
Multiplexer Module
The 40-785B-531 is a single 6-channel 26.5GHz terminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
For Conduction Cooled ΜTCA Chassis
UTC003
-
The VadaTech UTC003 is the most feature-rich MCH (MicroTCA Carrier Hub) for the Conduction Cooled μTCA chassis in the market. It’s management software is based on VadaTech’s proven Carrier Manager and Shelf Manager. The MCMC manages the power modules, the two CU (Cooling Units) and up to 12 AMCs within the μTCA chassis. It also interfaces to and manages the on-board fabric interfaces. The module is available with PCIe, SRIO, 10GbE Layer 3 managed, and GbE Layer 2 managed. The UTC003 runs Linux 2.6 on it’s MCMC CPU and is hot-swappable and fully redundant when used in conjunction with a second instance of the module. The firmware is HPM.1 compliant which allows for ease of upgrade. The UTC003 provides Fabric (100 Mhz HCSL) clock to each AMC.
-
Product
Portable Engineered Test Cell
PET
-
PET is an innovative portable engine test cell. Most test cells are designed by an architect and built of conventional materials like bricks and mortar, making the cells immovable and inadaptable to changing requirements. Emprise has developed a practical alternative to this PET a portable and modular engine and component test cell.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5150 Series
Digital I/O Module
The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.
-
Product
PXI Very High Density Multiplexer, 24-Channel, 8-pole
40-670C-022-24/8
Multiplexer Module
The 40-670C-022-24/8 is a 24-channel, 8-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
