Timing
See Also: Time, Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Time Interval Analyzers
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 1 Channel
M2P.6530-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
Resistivity Imaging & Sounding System
Syscal Junior Switch
-
The Syscal Junior is an all-purpose resistivity imaging and sounding system for environmental applications. The system can be supplied as a standard imaging system capable of recording two measurements simultaneously. The second recording channel significantly improves data acquisition time when the instrument is fitted with internal switching board for 24 (Switch-24) 48 (Switch-48) or 72 (Switch-72) electrodes for Electrical Resistivity Tomography (ERT).
-
Product
Wideband Power Sensor, 50 MHz To 18 GHz
N1923A
Power Sensor
The Keysight N1923A peak power sensor provides peak, peak-to-average ratio, average power, rise time, fall time, maximum power, minimum power and statistical data of peak signals.
-
Product
Osprey / TXP Co-Processor
9740-T
-
Triple+ speed Windows/NT Osprey Co-Processor for five times the system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes FPJ11® compatible hardware floating point. Performance equivalent 3.8 times the DCJ-11® and 130% of FPJ-11. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. Qbus®/Unibus® support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel Qbus or Unibus adapter. Operates only under Windows/NT. WNT Support license included.
-
Product
Flow Measurement for liquids, gases and steam
-
Flow measurement for liquids, gases and steam. Consistent product quality, safety, process optimization and environmental protection – these are only a few reasons why industrial flow measurement is becoming more important all the time. Water, natural gas, steam, mineral oil, chemicals are some of the fluids that have to be measured day in, day out.
-
Product
Meter Software Module
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Level display as five digits number*Display selectable between acceleration, velocity and displacement*RMS, positive, negative and unsigned peak values, instantaneous value *Rotary speed measurement with Photoelectric Reflex Switch (only VM-METER+)*Main frequency (only VM-METER+)*Measurement at rotation speed or multiples (only VM-METER+)*Sound level meter (A and C weighted) and noise dose meter (only VM-METER+)*THD (distortion) measurement (only VM-METER+)*One VM-METER license can be operated simultaneously up to four times with different settings*Offline measurement
-
Product
Computer-Based Instruments
GT210PCIe
-
with the GT210PCIe you can determine any frequency to 0.01 part per million (eight digits) in just 1 mS, and resolve each time measurement to 8pS. Couple that with 2300 measurements per second, one of the fastest rates available and you can acquire more data in a single second than a typical GPIB counter can in one minute! Faster measurements and higher resolution, along with built-in statistics functions give you a more thorough analysis of your signal. Standard deviation, peak to peak jitter, or a graph of the measurements are available at the push of a button.
-
Product
Timing Board #1
TIO-10 #1
-
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. Bursts, delayed pulses, and frequencies can be generated on outputs. The input channel can be used to measure frequency or period.
-
Product
FieldFox and HSA Handheld Spectrum Analyzers
-
Carry Keysight-quality microwave measurements wherever you need to goBoost your readiness with an RF unit: every operating mode is flexible enough to meet the needs of novices & experts alikeEndure the harshest working conditions with analyzers designed for durability – completely sealed, rugged & weather-resistantSave time and ensure consistent results by automating routine tasks for basic spectrum analysis
-
Product
Universal Off-Line Handler
OLS Series
-
Developed as an economical and versatile solution, it adapts to any offline test application - ICT (In Circuit Test), ISP (Flashing) or FCT (functional). The design of this solution allows the quick and ergonomic change of fixtures , with a change time of less than 3 minutes.
-
Product
PCI-8512, 1‑Port, High‑Speed/FD CAN Interface Device
780683-01
CAN Interface
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Wireless System For Test And Measurement
TM400 Compact
-
The TM400 system was designed to provide the ideal link between calibrated test microphones and measurement equipment such as SIM®, SIA SMAART Live®, TEF® or other systems. By using a radio link, long cables can be eliminated thus saving time and providing opportunities for additional measurements to increase accuracy. The microphone can even be moved around in the venue while the audience is present – something that is impossible with a cabled measurement microphone.
-
Product
TCS Comfort
-
Maschinenbau Haldenwang GmbH & Co. KG.
Trip distance / tachograph meter integrated into the brake tester (only in conjunction with PC)Electronic control unit TCS shockproof (workshop-oriented) aluminum housing with connection D-Sub 25p / D-Sub 9pEntire operation via integrated time and data display, and your existing PC (OS: Windows).Complete measurement and programming of the tachograph types 1311, 1314, 1318, 8400, FTCO 1319 MTCO 1324, TVI 2400, SE 5000, EFAs, SmarTach, DTCO 1381 incl. Integrated dial measurementLCD 4 rows, 16 digits; backlit with an integrated smart card readerMobile and / or stationary usable instrument; used stationary as integrated into the brake tester and the computer; optionally a road measurement is possible.Expression of complete test reportData storage for customer and vehicle datamultilingualism
-
Product
PXI 3A Power MUX BRIC, 10-Channel, 24-Pole
40-571-105
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Universal Differential pH Water Quality Sensors
SD7500CD
-
Continuous online pH monitoring in wastewater and coating industrial applications leads to contamination and eventually requires sensors to be replaced. A differential pH sensor utilizes a measurement technique designed to extend the working lifetime of sensors in challenging applications. Replacing the sensor reference (salt bridge) and buffered electrolyte solution can prevent sensor replacements, saving time and money. Our SD7500 Series features a combination sensor output; these differential pH sensors can be used with any conventional pH/ORP transmitter.
-
Product
Instant Circuit-break Detector
-
King Design Industrial Co., Ltd.
*Independently detect instant circuit-break.*Can detect 10 loops simultaneously.*Minimum test range is 0.1 us.*Can follow product’s test condition to set the instant circuit-break monitoring time (0.1us~).*Beeper and indicator will rise up at instant break.*Accept customized order.
-
Product
350 MHz, 2 Analog Plus 16 Digital Channels Oscilloscope
MSOX3032A
Oscilloscope
350 MHz2 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Temperature Logger for Thermistor Probe
TGP-4020
-
Loggers with probes can be used to record temperature in awkward to reach areas or applications where a fast time response is required. A versatile range of probes are available for this unit and can measure between -40 to +125C. Like the logger, probes are waterproof to IP68.
-
Product
250 and 260 Series pH Handheld Meter Kits
-
Get easy-to-read and accurate readings with auto-hold, auto-stable, and real-time measurements with stability indicators. The Environmental Express® Oakton® 200 series of water quality meters features an electrode status indicator, which shows the condition of the electrode after each calibration. Easily view electrode condition, reading stability, measured parameter, and temperature in one screen. Don’t worry about accuracy in fluctuating temperature—ATC ensures measurement accuracy. The simple user interface features adjustable auto shut-off time ranging from 1 to 30 minutes. Self-diagnosing meters display measurement and meter issues for fast fault finding and troubleshooting. Easily take measurements and conveniently store meter and electrodes with built-in foldable stand on the back of the meter. Two grooves on the side of the meter serve as electrode holders, to hold up to 2 electrodes. Choose from two series—the 250 series feature 500 data points (scroll thru on meter) while the 260 series features 1000 data points, a real-time clock, and USB communication for data down loads.
-
Product
Hyphenated Technology
-
Evolved Gas Analysis (EGA) solutions couple two or more analytical technologies to greatly increase the power of analyses and save precious time by acquiring more information from a single run, creating a powerful and easy-to-use platform for materials characterization. EGA Hyphenation is a powerful tool in the analysis and identification of complex mixtures, both known and unknown, including identifying harmful chemicals in soil, quantitating components in polymers, determining leachables that may contaminate a product's packaging, identifying phthalates in PVC samples and more.
-
Product
Signal Generator, 20MHz, 2 Channel, Arb.
33512B
-
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
Product
Polarity Indicator Circuit Tester
CT8007
-
No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance electronic circuitry. Negligible current draw ( 1 microampere) is 30,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 6 and 28 Volt DC in battery powered systems
-
Product
4-CH RTD Thermal Input EtherCAT Module
EPS-3504
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Mini OTDR
FiberPal OT-8700
-
FiberPal OT-8700 series instruments, with power meter built-in, are new miniature, high performance optical time domain reflectometer which is designed as fiber troubleshooter for locating fiber connector, break and imperfections for access networks. It detects event locations along the optical fiber and displays the results on a 7” color LCD display. FiberPal OT-8700 series are light, reliable and easy to use, hence it is ideal for FTTX testing. The Application Software equipped is used for data analysis, processing and storage. With the USB Interface port, enabling FiberPal OT-8700 series to transfer test data to computer easily.
-
Product
Time Domain Reflectometer
IRG 2000
-
Cable fault location with the BAUR IRG 2000. The IRG 2000 impulse reflection measurement unit or time domain reflectometer is a handy, easy to carry device for single-phase cable fault pre-location. It is used in combination with a surge voltage generator on low-, medium- and high-voltage cables 0 - 65 km in length. It can also be used on live cables carrying voltage up to 400 V.* Easy and quick cable fault location* Light, compact and manageable* Main unit for the tried-and-tested pre-location method* Ideal for integration in measurement systems
-
Product
TamoSoft® Throughput Test
-
TamoSoft Throughput Test is a utility for testing the performance of a wireless or wired network. This utility continuously sends TCP and UDP data streams across your network and computes important metrics, such as upstream and downstream throughput values, packet loss, and round-trip time, and displays the results in both numeric and chart formats. TamoSoft Throughput Test supports both IPv4 and IPv6 connections and allows the user to evaluate network performance depending on the Quality of Service (QoS) settings.
-
Product
PCIe 14 Bit High Speed Digitizer - 400 MS/s on 4 Channels
M4I.4481-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Temperature Measurement IR Sensors & Detectors
M5
-
A thin film-based thermopile offering very low noise and a small 0.5mm diameter active area in a TO-5 package. This is one of the lowest noise thermopiles you can buy and provides a time constant 28ms time constant with Argon encapsulation gas.
-
Product
Order Tracking Analysis
-
Order Tracking is a general term describing a collection of measurement functions used for analyzing the dynamic behavior of rotating or reciprocating machinery for which the rotational speed can change over time.
-
Product
FPGA Image Processing (IP) Development Kit
ProcVision
-
Gidel’s Vision Pro Development Kit is an optimal solution for developing,validating, demonstrating and evaluating Image Processing (IP) andpipeline designs on FPGA.The suite is designed to provide a complete and convenient envelop enablingthe developer to focus strictly on the proprietary image processingdesign. The entire Vision Pro flow is within a single FPGA, independentof the final target application(s). The Vision Pro flow is composedof a pipeline that streams simulated data to the user image processingdesign under test (DUT) and then captures the design’s output streamfor displaying, storing, analysis and/or co-processing on host software.The entire process is performed on a single FPGA without the need foradditional peripheral connectivity or tools.Vision Pro suite is plug-and-play enabling the developer to begin at oncethe IP design development and validation. A simple design example providesthe developer immediate hands-on familiarization with the systemflow and supporting tools. The final design can be ported to any IntelFPGA device or other vendors’ devices (FPGA or ASIC) by replacing basiclibraries. To significantly reduce compilation time, initial design developmentmay be on a small FPGA device and later compiled for the targetdevice(s). The target implementation may use any FPGA board. For a fullImaging/Vision system solution, Gidel offers a number of off-the-shelfgrabbers and FPGA accelerators that are designed to utilize these imageprocessing blocks and Gidel Imaging Library (GIL).
