Optical Transmission
-
Product
Optical Power Meter - PXI
Power 1400 Series
Power Meter
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
Product
Automated Optical Inspection (AOI)
-
Automated optical inspection (AOI) is an automated visual inspection of printed circuit board (PCB) (or LCD, transistor) manufacture where a camera autonomously scans the device under test for both catastrophic failure (e.g. missing component) and quality defects (e.g. fillet size or shape or component skew). It is commonly used in the manufacturing process because it is a non-contact test method.
-
Product
Fiber Optic Light Source
-
Fiber optic light source is a fiber optic test equipment to measure the fiber optic loss for both single mode fiber cable and multimode fiber cables; usually the fiber optic light source is used with the fiber optic power meters. This fiber optical light source can provide wavelength output according to the specific requirements including the 650nm red source, 1310nm/1550nm wavelength for the single mode fiber and 850nm/1300nm wavelength for the multimode fiber. Used together with our fiber optic power meter, they act as an economic and efficient solution for the fiber optic network works.
-
Product
Field-installation Type Dissolved Oxygen Meter (Four-Wire Transmission, Membrane Type)
HD-200
-
HD-200 connects the DO (Dissolved Oxygen) sensor (DO-1100) and measures the DO in the sample water.The measurement method is membrane type polarography method. It is suitable for monitoring DO in wastewater treatment or aquarium for aquaculture.
-
Product
Near-Field Scanning Optical Microscope Platform
MoScan-F
-
MoScan-F is a device that enables you to get the best up-to-date available spatial optical resolution using the near field scanning optical microscope (NSOM) principle
-
Product
Long Range Straightness Optics
10775A
-
The Keysight 10775A combines a straightness interferometer and reflector to provide measurements over a range of 1 to 30 meters (3 ft to 100 ft). The optics form a highly-accurate optical straightedge that can measure the straightness of travel of machine-tool and measuring-machine coordinate motions with a resolution of 0.1 micrometer (10 microinch).
-
Product
OEM Optical System Design and Manufacturing
-
Prior Scientific has successfully developed many innovative and custom OEM products for our industry partners. Any opportunities to develop, design or manufacture OEM products are always considered.
-
Product
Portable Optical Power Meter
CARY-PM300
-
The CARY-PM300 portable Optical Power Meter is a newly designed fiber optic tester,which aims at the installation, engineering acceptance and maintenance of fibernetwork. Combined with CARY-LS300 handheld optical light source, it offers a quickand accurate testing solution on both SM and MM fibers.
-
Product
Optical Fiber 13×1 Switch
OFSW - 13 × 1
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 13×1 is a 13×1 prism optical switch. It can support 13 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
Fiber Optics
-
The Neoptix product line includes fiber optic temperature sensors for transformer windings temperature monitoring and for laboratory, industrial, and medical applications.
-
Product
Optical Backscatter Reflectometer
OBR 4600
-
The Luna OBR 4600 Optical Backscatter Reflectometer (OBR) is a powerful tool for testing and analyzing loss in short-run networks and components. The OBR 4600 is an ultra-high resolution reflectometer that features a spatial sampling resolution of 10 microns, zero dead zone, and backscatter-level sensitivity. The OBR 4600 offers industry leading technology to precisely track loss and polarization states, allowing you to “see inside” your components and systems.
-
Product
3D Optical Profilers
-
ZYGO's 3D Optical Profiler instruments enable precise, quantitative, ISO-compliant, non-contact surface measurement and characterization of micro- and nano-scale surface features, capturing up to two million data points in just seconds. Applications range from topography and waviness to roughness and microstructure characterization on samples as that vary from ultra-smooth sub-angstrom optical surfaces, to extremely rough and diffuse 3D printed surfaces.
-
Product
Panel-mount Type pH Meter (Four-Wire Transmission, Pulse Proportional Control)
HP-480PL
-
HP-480PL industrial pH meter is a pH meter with a pulse proportional control function, which can drive a pulse pump directly.It connects pH sensor and measures pH and temperature in the sample water.As the HP-480PL has a high injection resolution per pulse, it can be used to control a pulse pump as part of a system for processing involving fine control of pH values, for example controlling the pH values of microscopic or small samples.
-
Product
Monolithic Laser Combiners & Precision Optics
-
For more than 40 years, our vertically integrated in-house production teams have relied on collaborative interdisciplinary processes to drive product performance and manufacturability. And we back up everything we do with industry-leading metrology to ensure that the building blocks of our technology – fabrication, coating, and assembly – permanently align to your exacting specifications to deliver consistent, shipment-to-shipment product performance, even in the most demanding environments.
-
Product
Fiber Optic Loopback
LC/SC/MTRJ
-
Fiber Loopbacks is designed to provide a media of return patch for a fiber optic signal; typically it is used for fiber optic testing applications or network restorations. For the testing applications, the loopback signal is used for diagnosing a problem. Sending a loopback test to network equipment, one at a time, is a technique for isolating a problem.
-
Product
Base for Optics Height Adjuster and Post
10784A
Mounting Panel
The Keysight 10784A Base provides a mounting plate for the 10785A Optics Height Adjuster and Post. The 10784A is an accessory complementing a family of measurement optics and lasers that constitute the 5530 Laser Calibration System.
-
Product
Fiber Optic Inspection & Cleaning
-
One of the most basic and important procedures for the maintenance of fiber optic systems is to clean the fiber optic equipment.
-
Product
Water Vapor Transmission Rate WVTR Tester
WPT Series
-
Water Vapor Permeability Tester is based on the Gravimetric method and is applicable to the water vapour transmission rate (WVTR) test of plastic films, composite films, sheets and other materials.
-
Product
Light Measurement Input Optics
-
International Light Technologies
Light measurement units are defined around very specific spatial responses. A carefully designed input optics system is essential if measurement accuracy is to be achieved.
-
Product
Optical Fiber 1×13 Switch
OFSW - 1 × 13
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×13 is a 1×13 prism optical switch. It can support 1 optical fibers input and 13 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
RGB Digital Fiber Optic Amplifier
CZ Series
-
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
Product
X6 Optical Fiber Fusion Splicer
-
Smart-connected APP, Splicing record management, Intelligent burglary-resisting system 1 sec. topspeed boot time, 6 sec. splicing time, 12 secs. Heating time. 3D protection cover reduce risk and unpredictability. Handy, lightweight, anti-dropping solid and durable.Hi-Speed USB connection internet remote control.
-
Product
CATV RF Optical Receiver
L-RF-MN-RX
-
The QuestTel''s L-RF-MN-RX module optical receivers are versatile, low-cost and compact optical receivers for use in HFC fiber applications. It is perfect solution for the transport and distribution of CATV RF signals over fiber optic cable. The L-RF-MN-RX module housed in a small housing and have adjustable RF output level. May be used as a hand held device for testing, or placed at a customers premise for the reception of cable television services. The Receiver is designed to operate with a very low optical input level between the range of +3dBm to -12dBm.
-
Product
Optical Inspection
3D AOI
-
In contemporary electronics manufacturing, automatic optical inspection (3D AOI) is an established component of quality control. A company purchasing a 3D AOI system wants to ensure that it is manufacturing its electronic products in the very best quality and can guarantee they will have a long service life. The Viscom systems feature superlative 3D and software attributes to deliver excellent measurement accuracy and exceptional image quality. Our 3D AOI systems are designed for simple programming and can also be flexibly adapted to new requirements, allowing them to easily accommodate fast product changeovers as well as large production quantities.
-
Product
X4 Optical Fiber Fusion Splicer
-
Smart-connected APP, Splicing record management, Intelligent burglary-resisting system 1 sec. topspeed boot time, 6 sec. splicing time, 12 secs. Heating time. 3D protection cover reduce risk and unpredictability Handy, lightweight, anti-dropping solid and durable. Hi-Speed USB connection internet remote control.
-
Product
Optical Probes - Low Bandwidth
P6701B/P6703B
-
Depend on Tektronix to provide you with performance you can count on, and industry-leading service and support.- Broad Wavelength Response 500 to 950 nm or 1100 to 1700 nm- High-bandwidth DC up to 1.2 GHz- High Gain 1 V/mW- Low Noise <11 pW/√Hz- Probe Connects to DPO7000*1 and DPO/DSA/MSO70000*2Series- SONET/SDH and Fibre Channel Reference Receiver Performance
-
Product
Panel-mount Type Conductivity Meter (Four-Wire Transmission, 2-channel)
HE-960CW
-
HE-960CW connects conductivity sensor (ESH /FS Series) and measures conductivity and temperature in the sample water. It is ideal for the conductivity control of the purified water, pasteurized water, and water for injection that are used in the production of pharmaceuticals.And we have developed a lineup of electric conductivity sensors that can be used in conjunction, from the conventional insertion type to the flow-through type with improved cleaning and sanitary properties.
-
Product
Optical Light Source
TM102N
-
TM102N Optical laser light source is a self-developed instrument, Which features advanced control technology , high output, ultra low-power operation. It can work at 1625nm, 1550nm, 1490nm, 1310nm, 1300nm, 850nm、650nm, single wavelength, dual-wavelength or tri -wavelength. It can export a variety of modulation frequency (CW, 270HZ, 1KHZ, 2KHZ). It is widely used in optical communication, optical measurement, optical fiber sensing, and so on.
-
Product
Fiber Optic Talk Set
TT1315
-
The Yamasaki TT1315 Fiber Optic Talk Set is designed to achieve crystal clear, full duplex, hands-free communication over any spare singlemode fiber optic cable. Sold as a two pack, these talk sets give fiber optic installers and technicians a reliable and cost effective solution to communicate over long distances for a long period of time, whereas RF devices can often be a costly and ineffective option. The Yamasaki TT1315 Fiber Optic Talk Set is a breeze to use with a simple menu system, automatic call detection, user-selectable back light, flip-out stand and comfortable headset.
-
Product
Mini Optical Spectrum Analyzer
-
Shenzhen Golight Technology Co.,Ltd
Mini OSA is based on MEMS tunable filter and high precision photoelectric control unit and detection unit. Its measurement precision is superior to the traditional OSA in C-band and O-band. And built-in USB communication interface is easy for system integration and SDK.
