Test Connectors
-
Product
Laser Diode Reliability Burn-In / Life-Test System
58602
Test System
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
Product
GSM/EDGE Analysis Using NI PXI RF Test Instruments
NI-RFmx GSM/EDGE
Test Instrument
The NI-RFmx GSM/EDGE personality is a highly optimized API for performing physical layer measurements on GSM/EDGE cellular standard signals. NI-RFmx GSM/EDGE is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
15-Pin D-Type Connector, Male
40-963-015-SM
D-Sub Male Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 15-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Test System
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
37-Pin D-Type Male Solder Pin HV
92-960-037-MHV
D-Sub Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
Combination Board Functional Test System
QT 4256 ATE
Functional Test
Qmax Test Technologies Pvt. Ltd.
QT 4256 ATE is a combination Board Functional Test System , a main frame Automated Test Equipment (ATE) which can be configured up to maximum of 1280 Bi-directional digital channels ideal for testing circuit card assemblies of high level of complexity and whether it is a legacy or new generation PCB.
-
Product
6TL29 Semi-Automated Test Platform
AQ377
Test Platform
- Compact, transportable and modular test platform.- Ready for ICT, FCT, Boundary Scan, HiPot, Vision or any combination of the previous technologies.- Mass interconnect 9025 Receiver from Virginia Panel.- 100% Compatibility with Inline Test Fixtures (P/N: AT799, AN133 and EB773).- Free available rack space: 47U height- Multi-stage pressure at 3 levels.- FastATE Technology & YAV Modules compatible.- Phi6 Dispatcher Interface.- CE Compliant.
-
Product
Modular Functional Testing Platform
OTP2
Test Platform
Functional testing is an important part of product development and manufacturing and is used to ensure quality, performance and reliability from launch to end of life. A modern, future-proof functional test system must meet many criteria in order to meet the ever-growing demands of the industry. The OTP 2 open test platform developed by LXinstruments meets the following requirements for a dynamic and highly competitive market.
-
Product
Test Lead, BNC Connector To BNC Connector Board
16048A
-
Extend the measurement port with a four-terminal-pair configuration that enables the attachment of user-fabricated test fixtures.
-
Product
Non-Signaling RF Test Platform for Validation & Production
Universal Wireless Tester
Test Platform
Wireless communication standards are increasingly integrated into vehicles as well as smart home and Internet-of-Things applications. They form the basis for connected services, advanced HMIs, and autonomous driving. The combination of constantly evolving standards and the integration of multiple wireless technologies with many RF channels into new product designs means that measurement speed and quality are becoming a priority.
-
Product
37-Pin D-Type Female Connector Block
40-965-037-F
Connector Block
Suitable for use on the front of modules this connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
Universal Test System
LEON System
Test System
A universal ICT, FCT, ISP and Boundary Scan platform.Based on the ABex platform, which directly integrates Konrad analog bus technology and PXI/PXIe in one chassis, the LEON platform can be configured to solve various test challenges. Due to this architecture only one system provides the complete test flow combining ICT, ISP, Boundary Scan and FCT.Various form factors and configurations allow a perfect combination between cost, speed and test coverage. The modular architecture provides the possibility to reconfigure or upgrade the systems based on your test needs.The LEON System software provides a powerful development and test execution environment which directly supports NI TestStand. All systems and components could be integrated into third party software using supplied APIs.
-
Product
200-Pin LFH Connector Block, Female
B200LFX-2F-5B
Connector Block
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
Product
NI's Wireless Connectivity Functional Test Solution
Functional Test
The proliferation of wireless functionality in electronic devices is pressuring test developers to deliver more complex testers within shrinking project schedules. Evolving standards and the integration of multiple wireless technologies into new product designs mean developers must prioritize measurement speed and quality to maintain throughput and yield targets. For a solution to meet these sorts of demands, it must:
-
Product
CATR Benchtop Antenna Test System
ATS800B
Test System
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
test
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
Test Module
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Product
Test System Optimized for High-Performance Digital and SoC
ULTRAWAVEMX44 and ULTRAWAVEMX20-D16
Test System
Teradyne is the leader in RF/wireless device testing and has a large installed base of UltraFLEX test systems with the UltraWave24 RF instrument. As new devices for handset and base station applications are introduced using mmWave technology, Teradyne’s mmWave instrumentation has expanded in anticipation of new testing demands.
-
Product
EMI Test System
TS9975
Test System
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
ARINC 818 Tester
Test Platform
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
Product
500-Pin SEARAY Connector, Male Without Backshell, 2 Amp, 250 Port
C500RMX-4SB-4B
SEARAY Male Connector
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Functional Test for Engineering Lab
Spectrum BT
Functional Test
Designed to meet the needs of product engineering labs, production lines, test development centers, and repair depots, the Spectrum BT is a configurable and scalable functional test system. This focused system solves typical functional test coverage challenges throughout the defense/aerospace product life cycle—and it’s upgradable as test requirements evolve.
-
Product
200-Pin LFH Connector, Female, UNC Female Screwlocks, With Backshell
40-961A-200-F
LFH Female Connector
This connector is designed to allow users to directly terminate with soldered connections to the 200 pin LFH connector.
-
Product
Headlamp Test Platform
Test Platform
Leverage 25+ years of automotive test experience, with the specialized design and manufacturing of automotive lighting testers. Using specialized know-how in this field, including photometric, electro-mechanical equipment and software solutions, accelerate your time to market with a higher quality product.
-
Product
Connectors
-
Ever since our company foundation in 1978, connectivity has held a special place at the core of the increasingly system-oriented MacArtney organisation. Even today, connectors, cables, terminations, junction boxes and everything beyond and in between, are involved in pretty much everything that we do, and in many ways, it is connectivity and integration that have paved - and still pave - the way for most other innovative MacArtney products and systems.
-
Product
In-Circuit Tester
Sparrow MTS 30
In-Circuit Test System
The Sparrow MTS 30 is a 19“ test system that can be integrated into any standard rack. The In-Circuit tester can also be used as benchtop test system. With this compact and flexible tester you can perform both analog and digital In-Circuit and functional tests.
-
Product
Fine Pitch Connector Test
-
C.C.P. Contact Probes Co., LTD.
Our Ceramic/Aluminum sockets have a lifetime of up to 30,000 cycles.
-
Product
Connectors
-
Microwave coaxial connectors transmit radio frequency signal between circuits. They contribute to the development of high-performance communication equipments, such as smartphones, tablets and wearable devices with smaller and thinner size.
-
Product
Test Socket Based Elastomeric Matrix Connectors
-
Z-Axis offers a wide range of high performance test sockets, which are based on our elastomeric matrix connectors, for wide range of IC packages (BGA sockets, LGA sockets, etc.), coaxical, and wafer level; and for testing high speed, digital, analog, and RF signals etc.
-
Product
JTAG Functional Test
JFT
Functional Test
JFT comprises a series of software modules that support boundary-scan test and programming activities under Python, National Instruments LabVIEW and Microsoft .NET framework. Using JFT users can create JTAG/boundary-scan test application scripts, VIs or programs for PCB assemblies and systems that control individual driver/sensor pins, groups of pins declared as variables or register bits. These applications are typically used to test logic devices or mixed signal clusters and can also be transformed into re-usable test 'modules'. Pairing JFT with JTAG CoreCommander emulative test modules gives an effective, low-cost system for performing tests through embedded device peripherals (ADCs, Memory Controllers etc..)
