Showing results: 481 - 495 of 588 items found.
-
HGM-MZ -
IMR Environmental Equipment, Inc.
The Multi-Zone Monitor provides continuous detection of refrigerant gas levels in up to 16 separate test zones and can be fitted with an optional two channel 4-20 mA current loop board for connection to remote monitoring equipment. Multi-Zone monitors retain a log of previous readings that can be easily accessed for analysis. Four relay contacts are provided that can be programmed to trigger external alarm devices in the event of a system fault, or if a leak (small), spill (medium) or evacuation (large) level of gas is detected, while audible and visual front panel indicators show alarm and fault conditions.
-
Excalibur Systems, Inc.
The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.
-
JT 2147/eDAC for MAC Panel -
JTAG Technologies Inc.
The JT 2147/eDAK is a new variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within a MAC Panel ‘Scout’ mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry plus four independent, programmable TAP modules (two of type JT 2149 and two of type JT2149/MPV) on a single board that matches the MAC Panel Direct Access Kit (DAK) form factor. Overall this configuration offers four Test Access Ports, 64 Digital IO Scan channels and reconfigurable (SCIL) capabilities
-
WT-100 -
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
National Technical Systems
NTS electronics failure analysis capabilities can be utilized to improve yield, determine root cause of failure, extrapolate life expectancy and improve reliability, and increase performance on integrated circuits (ICs), printed circuit boards (PCBs), and passive surface mount devices as well as materials and assemblies.Electronics F/A can provide detailed information regarding the performance of materials and devices in their intended end-use application. When a device or material does not meet its performance expectations, a F/A should be performed to identify the root cause of failure. The information presented in the root cause F/A will allow the product designer, manager, test and process engineers, or end-user to identify design, selection, test, and process deficiencies. Recommendations for corrective actions from the failure analysis report can then be evaluated and implemented to enhance product reliability and performance. By having an unbiased F/A performed by an independent test laboratory, the liability of a failed device or material can be converted into an asset, resulting in production of higher quality products.
-
AAF-2 -
Alligator Technologies
The AAF-2 is a multi-channel low-pass filter board designed for use in front of A/D converters with resolution up to 16-bits. It is ideal for filtering applications in sound and vibration testing, ultrasonics, acoustics, structural analysis, industrial, test, scientific and laboratory data collection and applied mechanical applications in electronics, aerospace, field research, automotive, and process control industries.
-
N1425B -
Keysight Technologies
The N1425B is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425B is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425B enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425B to the B2985B/87B.
-
N1425A -
Keysight Technologies
The N1425A is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425A is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425A enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425A to the B2985B/87B.
-
778572-36 -
NI
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2536 is a high-density 8x68 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring FET relays, the PXI‑2536 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Advanced Probing Systems, Inc.
APS produces electro-chemically machined pins in diameters between .020"-.040" in a variety of materials for use in various applications. These “large diameter pins” are used in various medical applications, industrial applications, board testing, LED & LCD test and as components in small tools. APS’s design services can help you select the optimal material from tungsten, beryllium-copper, Paliney 7® or various stainless steel alloys or work with the material of your choice. Pins can be produced with either a sharp or radius (rounded) tip. Tapers can be highly polished, slightly polished, matte or neutral in finish.
-
TetraTek Products, Inc.
World-class integration of electronic test equipment, instrumentation, test fixtures, automation, load simulation,data acquisition, and software . In partnership with two major leaders in high-technology automation, three very capable machine shops, a custom cabling company, a rapid prototype circuit board fabrication house and two large automated sheet metal manufacturing facilities we offer custom process and test equipment designed and manufactured for convenience and precision. Each component of our systems is carefully consideredto provide you with maximum performance consistent with easy maintainability and long term return on your investment.
-
CSP-30TS-011 -
ECT
high frequency probes for the PCBA test market. This next generation coaxial probe provides instrumentation-quality interface for broadband RF measurements exceeding 20GHz, delivering superior performance while seamlessly mating with pads, vias, and other board features. The CSP-30TS-011 RF probe combines several innovative features to provide a truly reliable and cost-effective testing solution.
-
igentic® 621t -
Sterner Automation Limited
Growing demand for light emitting diode (LED) products and increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. The igentic® 621t is a flexible PCB tester that ensures quality while increasing production. The tester can handle multiple PCB products and test for light measurements, resistance and push button or post detection, as required.
-
FloTHERM -
Mentor Graphics Corp.
Perform thermal analysis, create virtual models, and test design modifications of electronic equipment before physical prototyping. FloTHERM uses advanced CFD techniques to predict airflow, temperature, and heat transfer in components, boards, and complete systems, including racks and data centers. It''s also the industry''s best solution for integration with MCAD and EDA software.
-
B-1001-H -
ROSS ENGINEERING CORPORATION
*5kV to 15kV Peak Test*3A Continuous*50VA Max Interrupt*NO, NC, DT, Single & Multi-Pole*Safety Encapsulation*HV Leads Available*Compact *Long Life*High Vibration / Shock Resistance*Maximum Creep distance between HV & Actuators Terminals *Tapped base, Turret or Hook terminals, PC Board mounting, Quick disconnect or HV leads available
