Surface Resistance
-
Product
Air and Water Permeabilityin Concrete Both At and Below the Surface
Poroscope
-
Poroscope Plus measures the time it takes for air to flow into a known volume of a sealed, evacuated chamber in the concrete. While the vacuum reduces from -55 Kpa to -50 Kpa, a measure of air permeability is determined. For water permeability, Poroscope Plus uses the same chamber filled with water, and measures the total time in seconds for a volume of 0.01 ml of water to escape.
-
Product
Oil Resistivity & Tan Delta Test Set-Up
-
This testing set is an automated instrument, widely used for measuring electrical characteristics of insulating liquids, transformer oil and other insulating material samples.
-
Product
Handheld Turns Ratio & Winding Resistance Tester
TWR-H Series
-
Handheld TWR-H device is DV Power single-phase instrument designed for measuring transformer winding resistance and turns ratio.The instrument has two output DC sources for measuring transformer winding resistance. The first DC source can output up to 2 A DC and is used for injecting current to the transformer’s high voltage winding. The second DC source can output up to 10 A DC and is used for testing the transformer’s low voltage winding. This is especially useful when measuring winding resistance of distribution transformers. These transformers have large turns ratio and therefore a big difference between resistances of high voltage and low voltage windings. Upon the winding resistance test, it is also possible to demagnetize the transformer core. The demagnetization process is completely automatic and safe.Together with the turns ratio, the instrument also measures excitation current and phase shift. This enables detecting transformer core or winding turns failures which cannot be spotted by measuring turns ratio only. The instrument can output test voltage up to 40 V AC for this test, but it can also output a very low test voltage of 1 V AC which is necessary for turns ratio verification of the majority of current transformers.TWR-H is powered by an internal Li-Ion battery. Up to 100 tests can be performed with a fully charged battery.
-
Product
Insulation Resistance Meter
AMIC-10
-
The AMIC-10 digital insulation resistance meter is used for direct measurements of the insulation resistance of electrical equipment working with voltage up to 1 kV. In addition, this meter makes it possible to measure compensation and protective connections, low-voltage resistance measurements and DC and AC voltage measurements.
-
Product
Metal Foil Llow Resistance Chip Resistor
MFR (Metal foil)
-
*Low Resistance / TCR / EMF 9only FOR MnCu) / Inductance*Excellent long term stability*RoHS compliant and halogen free.*Lead free.* High precision current sensing and voltage division.
-
Product
High Resistance Meters
-
Measurements International Ltd.
Direct or Substitution Measurements, Automatic and Manual Operation, No Temperature Coefficient, Multiple Modes of Operation.
-
Product
Winding Resistance Meter 50Amps, 2 Channels
WR50-12
-
Raytech Digital Winding Resistance meter WR50-12 is the enhanced version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Floor Resistance Test Kit
PMK-152
-
The PMK-152 Floor Resistance Test Kit contains the instruments you need to take resistance measurements.The PMK-152 includes Prostat's PRS-812 Resistance Meter with 5 pound conductive rubber electrodes. You can take measurements at 10 and 100 volts with accuracy within ±5%.
-
Product
Non-contact Inline Resistivity Measurement Module
NC-110 (NC-110PV)
-
*Possible to measure sheet resistance without contact by Max. 3 types of probes*Suitable for production line and tranceportation system*Connect to host PC by LAN to send measurement command and data
-
-
Product
Welding Resistance Tester
WRT
-
The Welding Resistance Tester is used in battery assembly lines to detect defective intercell connections. It is equipped with a 5-channel test head for car and truck batteries. It features 1-20 O DC resistance ranges and a multi-line LC display for OCV, CCV, and DCR measurements for 5 intercell connections.
-
Product
New Battery Resistance Tester
-
Hangzhou Xun Anda Electrical Co., Ltd.
maximum capacity of the battery:200AH/2000CCA(SAE)Voltage test range: 1.5-15VDCWorking voltage 1.5-15VDC,powered by the tested batterMaxim Power Consumption: around 0.5WOperating temperature: -10°C~50°C Operating humidity: 30%~90%, without condensationdisplay modes: Four different colors LED indicatorbutton: 3 buttons.Test Standard: SAE,DIN,EN,IEC,CA.
-
Product
Surface Mount-to-DIP JEDEC SOT-25, SOT-23A-6 Adaptor
1110748
-
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
Product
Anti-Surge Chip Resistors (Double-Sided Resistive)
-
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
-
Product
Contacts Resistance Tester
JYK II
-
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
Product
Fixed Writing Surface for Double-Bay 24" RA & RC Cabinets
WS2-124
-
This fixed shelf / writing surface for a double-bay RA & RC cabinets spans the full width of the cabinet and extends 18” in front.
-
-
Product
Surface Analysis
Innova-IRIS
-
This provides researchers a perfect combination of chemical or crystallographic information at high spatial and spectral resolution with the most advanced atomic force microscopy characterization. The Innova-IRIS can be integrated with your choice of a leading Raman system to provide the best opaque sample TERS investigations available today. However you tailor your system, your application will benefit from Bruker exclusive, high-contrast IRIS TERS probes and the best tip preservation and lowest drift, guaranteeing that alignment is preserved even over the optical integration times necessary to interrogate weak Raman scatterers.
-
Product
Earth Resistance Clamp Meters
-
Precision Mastech Enterprises Co.
Specialized, non-intrusive electrical testing tools designed to measure grounding system resistance without disconnecting the ground rod or using auxiliary electrodes.
-
Product
Live Line Clamp Insulation Resistance Tester
MLIT-1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy and convenient live line insulation measurements for servo motor,inverter motor and power line.・More than 0.1MΩ for power line.・More than 10MΩ for servo motor and equipment.
-
Product
Moisture Resistance/ Humidity Test
-
This test is performed for evaluating the resistance of component parts and constituent materials to the deteriorative effects of the high-humidity and heat conditions typical of tropical environments. Most tropical degradation results directly or indirectly from absorption of moisture vapor, and from surface wetting. These phenomena produce many types of deterioration, including corrosion of metals; physical distortion and decomposition of organic materials; leaching out of constituent components of materials, and detrimental changes in electrical properties.
-
Product
Compact Surface Mount Test Points
-
Compatible with vacuum and mechanical pick and place assembly systems
-
Product
Digital Earth Resistance Tester
MODEL - KM 2030
-
Kusam Electrical Industries Limited
Display : 3½ Digit LCD display. Ground resistance measurements from 0 ~ 01Ω to 2000Ω with 0.01Ω resolution. Earth Resistance : 20Ω / 200Ω / 2000Ω. Accuracy : 20Ω : ± (2% + 0.1Ω); 200Ω / 2000Ω : ± (2% + 3). Earth Voltage : 0 ~ 30V. Accuracy : ± (3% + 5). Resolution : 0.01Ω. Working LED Indicator. Data Hold Function.
-
Product
Panel-mount Type Resistivity Meter (Four-Wire Transmission)
HE-480R
-
HE-480R connects resistivity sensor(ERF sereies) and measures resistivity and temperature in the sample water.The feature is the high-precision temperature compensation function.Its high-performance temperature compensation makes it ideal for sequential monitoring of ultra-pure water used in manufacturing processes in the semiconductor field, and many other fields, including the areas of electrical goods, foods and medicines.
-
Product
Surface Mount Reed Relays
Series 200
-
Surface Mount Reed Relays. Wide range featuring dry or mercury wetted switches. Coaxial version for high speed digital or RF up to 6 GHz. 5, 12 or 24 volt coils with optional diode
-
Product
Resistance Wire Bonding
-
Electronic Systems of Wisconsin, Inc.
ESW's Resistance Wire Bonding System comes equipped with the latest features the market has to offer. Our system is capable of bonding armatures, stators or coils. The on-screen display in our bonder makes it easy to read, track, and record your bonding data. If desired, ESW offers complete electrical testing of the part prior to the bonding sequence as well. This ensures only good parts that have been electrically tested are processed through bonding. It is our duty to make sure you never have to worry about losing important information again. Our Sales and Engineering staff will work closely with you to make sure that a bonding systems will meet your needs. See the slideshow below to see some of our Resistance Wire Bonding Testers.
-
Product
Resistivity Meter of Powder Composites
RM-200
-
The resistivity meter is fully automated and does not required any adjustments. The measurement is made by using the four-point contact probe on the ring (ø60 x ø50 x 5mm) and rectangular prisms samples (6 x 6 x 60÷80mm). The measurement results are automatically saved in meter memory, what allows user to manage of data. The RM-200 contain series connection which allow the data transmission to PC.
-
Product
Internal Resistance Testers
-
The Battery Internal Resistance Tester is essential for assessing the health and performance of stationary reserve power batteries. Designed for efficiency, this tester measures internal resistance, helping to identify potential issues before they impact battery performance. By providing accurate diagnostics, it enables proactive maintenance, ensuring reliability in critical applications. This advanced testing equipment is an invaluable tool for enhancing battery longevity and optimizing energy storage systems.
-
Product
High-precision Surface Inspection for Wind Turbine Blades
waveCHECK™
-
8tree's waveCHECK is a handheld-portable 3D-inspection tool for inspecting wind turbine blades in manufacturing and operation. Its efficient detection of surface defects and instant visual feedback revolutionize surface inspection.It can detect wrinkles, steps, gaps, rain erosion and any other surface damage.
-
Product
Transformer Winding Resistance Tester
KRI 9310
-
KRI 9310 adopt Kelvin four-wire testing method, which effectively eliminates the influence of the resistance of the test line on the test results. It can be able to increases the current to 10A by which can test extremely low resistance to 0.01 Ω(such as amorphous alloy, Copper-nickel, nickel-chromium-iron, iron-chromium-aluminum etc). For the tested objects with high resistance value (CT/PT), the instrument can extend the range to 20 kΩ，so the wide resistance test range enables KRI9310 can cover 80% of the power transformer products on the market and switchgear bus-bar cable etc. The power of the tester use the built-in rechargeable lithium battery that can test hundreds of transformers by one time charging.
