Blades
-
product
Automotive Current Tester LCD Display
77102
This automotive current tester with LCD display, plugs directly into the fuse box and can be used on mini, standard and maxi fuse connections. Blades may get hot during use and care should be taken for 2mins whilst they cool down. Fits mini and maxi fuses. Current range 0-80AMP. Safe and easy way to check automotive current.
-
product
High and Low Temperature Humidity Chamber
GDJS/GDJW
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
product
Impact Tools
D814™ Series
Make effortless, uniform connections with Fluke Networks’ D814™, all-in-one, telecom punchdown tool. Its adjustable impact wheel has high and low settings for any type of termination. Automatic spring mechanism provides right impact to seat and/or terminate wires. Compartment at the end of the tool stores an extra blade.
-
product
Strain Measurements and Experimental Stress Analysis
Experimental structural testing using strain gauges is necessary in a wide range of applications from airframes and sub-assemblies down to individual components such as turbine blades, satellites, wind turbines, buildings, bridges and many others. These tests enable the engineers to compare the acquired data with the predicted results from the design calculations.
-
product
Woltman Meter
Key structure is made up of rotary carried helical blades which goes around as the same direction of water flow.
-
product
Field Fiber Cleaver
HW-09C
Shanghai Fibretool Technology Co.,Ltd.
The Fibretool HW-09C is a single fiber cleaver designed to accommodate either 900µm buffered or 250µm coated fiber. The HW-09C cleaver's quick and easy three-step operation is well suited for mechanical splice and quick termination field connector applications. The leaf spring base is ruled to allow for cleave lengths of 2 to 20mm. The standard carbide blade will perform up to 6000 cleaves before replacement.
-
product
11th Gen Intel Xeon Compact PCI Blade
CP6007-SA
CP6007-SA is based on 6-core or 8-core 11th Generation Intel® Xeon® processors with 10nm technology, with outstanding performance-per-watt values. Its scalable power budget allows users to tailor the power dissipation to their requirements. 32GB soldered memory and the option for an additional 32GB SODIMM with ECC is provided.
-
product
Dual Zipcord Fiber Buffer Thermal Stripper - TFS-900
Shanghai Fibretool Technology Co.,Ltd.
TFS-900 900um buffer thermal stripper design small, lightweight, easy to use and reliable, longitudinal peel, peel force is small, the high quality of stripped fiber; blade durable and easy to replace, using linear bearing guide and thermal stripping to ensure no damage to the fiber, easy to strip coating, stripping speed and other characteristics. With the fixture using the strip dual core optical fiber
-
product
3U CompactPCI Quad-Core Intel Atom® Processor X Series Blade
cPCI-3640 Series
- Low power quad-core Intel Atom® x6413E Processor (formerly Elkhart Lake)- Up to 32GB DDR4-2400-3200MT/s ECC soldered memory- Optional onboard SSD support- Flexibility in IO selection- Extended temperature -40 to 85 degree C supported
-
product
Blade Socket Tester
RV 7
The RV 7-Blade Socket Tester offers a fast, easy way to isolate a lighting problem to the trailer or towing vehicle. A must have for anyone who deals with hitch and lighting hookup installations, it tests the output of towing vehicle’s RV 7-blade lighting socket.
-
product
Blade Timing Analysis Software
Blade Timing BT
APEX Turbine Testing Technologies
BT is a data analysis software product for post-processing tiptiming data from laser-based and capacitance-based tiptiming systems (also known as NSMS).
-
product
Circular Blade Crosscut Tester
MCT-5
Is designed to test the adhesion and brittleness of dry coats of paint on their substrate by means of a set of six circular blades and two guide blades.
-
product
3U CompactPCI Serial Blades
The PICMG CPCI-S.0 CompactPCI Serial standard, which evolved from the PICMG 2.0 specification, is the fastest, most versatile, most cost-effective open standard for CompactPCI (CPCI). The Serial standard is mechanically and electronically compatible with 3U and 6U euro-cards, defining an interface for high-speed switched fabrics with a star topology. Point-to-point connectors allow up to eight peripherals on one system slot without switches or bridges. Ethernet data transfer can be configured with full mesh topology, which allows up to 1000Base-T connections to all peripheral slots for redundant, safety-critical systems.
-
product
AdvancedTCA® Carrier Blade with 4x Intel® Xeon® Processor E3-1515M v5 COM Express Modules and FM10420 Multi-Host Controller
aTCA-9400
- 4x COM Express Type 6 module slots supporting ADLINK Express-SL/SLE with Xeon® Processor E3-1515M v5 (45W)- Integrated Intel® GT4e GPU providing high-performance H.264/H.265 transcoding- COMe modules connected by Intel® Ethernet Multi-host Controller FM10420, supporting up to 25Gbps Ethernet bandwidth between CPUs- 2x 10G SFP+, 4x 1G RJ-45 Ethernet on front panel- 2x 10G to Fabric channels, 2x1G to Base channels
-
product
Test Switch
The W3TS Test Switch, a miniature knife blade switch (5/8 inch centers including barrier) with #10-32 stud terminals, is available in three types: Basic Switch, Short-Circuiting Switch (Shorting Switch), Test Jack Switch
-
product
3U VPX – OpenVPX Backplanes
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. OpenVPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
-
product
7-WAY Blade & 4 Flat Connector Tester
3536B
Peaceful Thriving Enterprise Co Ltd
This is a tester to test the function of the 7 way connector of the vehicle. User simply plug the tester with the 7 way or 4 way connector, and switch on the corresponding function of the vehicle to check if the LED indication has lighted up correctly. Use in the garages, workshops where there is a need to check the configuration of circuit. Widely used to test trailer light circuits on most trucks, boats, trailer campers, caravans, food trucks and other trailers.
-
product
6U CompactPCI Rear Transition Module with AMD MXM Graphics Module
cPCI-R6500 Series
The cPCI-R6500 Series is 6U CompactPCI rear transition module (RTM) designed for use with ADLINK 6U CompactPCI CPU blades. The cPCI-R6500 is an RTM equipped with an ATI graphics module to provide additional graphics performance for embedded applications and supports comprehensive rear I/O functionality. Dual independent display output is via two DVI ports and an onboard Realtek ALC262 High Definition Audio Codec provides analog audio output from the audio controller on the CPU blade. The cPCI-R6500 requires a compatible 6U CompactPCI backplane with rear I/O support and correctly configured CPU blade.
-
product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
- ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch- 24-port fully managed Gigabit Ethernet switch- Pre-installed ADLINK PacketManager accelerates packet processing- Layer 2/3 switching with advanced support for VLANs, QoS and IPv6- Two 10 Gigabit Ethernet SFP+ uplink ports- Supports IPMI based on PICMG 2.9 (System Management Specification)
-
product
Optical Chopper
These high stability variable frequency optical choppers each include a set of chemically blackened photoetched chopping discs. The mini chopper is an excellent choice for applications requiring a compact package. The chopping discs come in a variety of slot apertures and allow operation. Beam diameter is limited to 0.75mm when using the 200-slot disc and 1.0mm when using the 40 slot mini disc. The easy-to-interchange blades are made of non-magnetic, half hard brass and can be used in combination. Chopping frequency is set by adjusting a ten-turn dial or by applying an external DC voltage to the BNC input. Reference output is a TTL pulse and is in-phase with chopping action. The 5 digit led display gives a direct read-out of the chopping frequency. Power: 90-130V or 180-260V; 50/60Hz; 12VA max. Power supply included. Choppers are often used together with lock-in amplifiers.
-
product
VME Backplanes
VME enjoys a strong, stable ecosystem, particularly in many of the areas involving x86 compute blades, I/O, digital signal processing, and areas requiring custom design. It also enjoys some cost-effectiveness due to its wide adoption in over 400 defense programs as well as in industrial automation.
-
-
product
Rugged SOSA-Aligned 3U VPX NVIDIA GPGPU Blade
VPX3-MXM-RTX5000
The VPX3-MXM/RTX5000 is a 3U VPX general-purpose GPU (GPGPU) blade based on the NVIDIA RTX5000, supporting 16GB GDDR6 graphics memory with 4x DisplayPort or 4x HDMI output. The VPX3-MXM/RTX5000 brings a new level of performance to visual graphics and computing applications, fully integrating hardware acceleration for both graphics and computing code, enabling hardware acceleration for a wider class of applications than ever before.
-
product
3U CompactPCI-Serial
Advantech offers 3U CPCI-Serial CPU blades, I/O blades and AC/DC power modules to build up solutions in railway, semiconductor, healthcare markets.
-
product
3U CompactPCI-Serial CPU Boards
Advantech’s 3U CompactPCI-Serial board offers latest Intel Xeon®/Core™/Atom based processor blades.
-
product
6 Port PCI Express
PEX 8533
The ExpressLane™ PEX 8533 device offers 32 PCI Express lanes, capable of configuring up to 6 flexible ports. The switch conforms to the PCI Express Base Specification, rev 1.1. The 32-lane switch enables users to add scalable, high bandwidth I/Os to a wide variety of applications including servers, storage, communications, blade servers, and embedded-control systems.
-
-
product
Load-to-Line Jumpers
200
TESCO’s Load-to-Line Jumpers (Catalog No. 200) allows the utility to perform meter maintenance without interruption of service to the downstream occupant. TESCO bypass jumpers are rated for 200 amps continuous duty and are made from a durable 1/8″ thick tin-plated copper with a durable insulating material covering everything except the blades.
-
product
Rugged Conduction Cooled 3U CompactPCI Processor Blade with Quad-Core Intel® Atom™ Processor
CT-3620
The ADLINK CT-3620 Series is a Rugged Conduction-Cooled 3U CompactPCI processor blade in single-slot (4HP) width form factor featuring a quad-core Intel® Atom™ SoC and soldered DDR3L-1333 ECC memory up to 4GB. Graphics is integrated graphics on the CPU and storage is provided by an onboard 32GB SSD. Rear IO signals include 2x GbE, 1x USB 2.0, VGA, 2x COM, and 1x SATA 3Gb/s, providing for expansion with an optional Rear Transition Module (RTM).
-
product
Pressure Mapping
WIPER
Evaluate wiper blade force profiles and interface pressure distribution.
