Windows
-
product
Low cost EDXRF Elemental Analyzer
NEX QC+ QuantEZ
Applied Rigaku Technologies, Inc
As a premium low-cost benchtop EDXRF elemental analyzer, the Rigaku NEX QC+ QuantEZ delivers wide elemental coverage with easy-to-learn Windows®-based QuantEZ software. Non-destructively analyze from sodium (Na) through uranium (U) in almost any matrix, from solids and alloys to powders, liquids, and slurries. The 50 kV X-ray tube and Peltier cooled silicon drift detector (SDD) deliver exceptional short-term repeatability and long-term reproducibility with excellent element peak resolution. This high voltage capability, along with multiple automated X-ray tube filters, provides a wide range of XRF applications’ versatility and low limits-of-detection (LOD).
-
product
Reference Cells For PIV-IV Systems
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
product
Elrec Pro Switch
The Elrec Pro Switch is a 10 channel Induced Polarisation (IP) and Resistivity receiver designed to improve productivity when recording deep profiles and soundings. Beside the classical arithmetic and logarithmic modes, ELREC Pro also offers a Cole-Cole mode and twenty fully programmable windows for a higher flexibility in the definition of the IP decay curve.
-
product
16 channel 16 bit Digital to Analog
CPCI-DA16-1
The CPCI-DA16 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA16 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
product
Software for Immunity Test METES-EMS series
METES-EMS is software for Automated Test Solution to meed Immunity Std. each for Keys : Support for latest Windows OS Access via USB/LAN interface to measurement equipments to achieve
-
product
ARINC 429 PMC Interface Module
PMC-429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Intelligent Mini Munitions Store Interface (MMSI) Module for Excalibur 800 Family of Carrier Boards
M8KMMSI
The M8KMMSI is an intelligent, Mini Munitions Store Interface [MMSI] module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards. Each module of the M8KMMSI contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped and may be accessed in real time. Each M8KMMSI module may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor and Bus Monitor.The M4KMMSI comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
0 to 1000 ppm CO Measurement Range
EL-USB-CO
The EL-USB-CO is a USB data logger that measures and stores up to 32,510 Carbon Monoxide (CO) readings over a 0 to 1000 ppm measurement range. The user can easily set up the logging rate and start time, and download the stored data by plugging the module straight into a PC's USB port and running the purpose designed software under Windows 2000, XP or Vista
-
product
BACnet
BOSS Explorer
Softdel’s BACnet BOSS Explorer is the ideal tool to easily monitor, manage, debug and control any BACnet network and connected devices. BOSS Explorer is a full-featured BACnet explorer program that runs on any Windows® computer connected to the network. It has an intuitive interface that is easy to use for both professionals and BACnet novices.
-
product
2-Channel 400MHz DDS Signal Generator
2940A
The 2940A is a two-channel 400MHz DDS Signal Generator that generates two independent sine wave output frequencies simultaneously from 200kHz to 400MHz in 1Hz steps. A Clock Generator configuration with ECL or LVDS clock outputs is also available. The 2940A is lockable to an external frequency standard or is used with its internal TCXO. Optional internal amplifiers and 60dB step attentators available. Set all parameters with front panel controls and LCD display or by computer using the RS232 serial interface. All settings can be saved into non-volatile EEPROM memory upon power down. Windows software included.
-
product
Multi-Interface TDM, Optical, And Packet/IP Rackmount & Probe Test Platforms
mTOP™
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
-
product
Micro ATX Motherboard With LGA1151 Socket 7th/6th Gen Intel® Core™ Processor, Intel® Q170, USB 3.0, SATA 3.0, Dual LAN, VGA, DisplayPort, DVI-D, And HDMI
MMB501
The MMB501 is powered by the LGA1151 socket 7th/6th generation Intel® Core™ i7/i5/i3, Pentium® and Celeron® processors (formally codename: Kaby Lake/Skylake) with Intel® Q170 chipset. The MMB501 supports four high bandwidth 288-pin DDR4-2133/2400 with a memory capacity up to 64GB. The industrial-grade micro ATX motherboard is expandable with one PCIe x16 slot, two PCIe x4 slots, one PCI slot and one full-size PCI Express Mini Card slot. Moreover, the embedded board supports triple-display via DisplayPort, HDMI, DVI-D and VGA interfaces. Furthermore, this outstanding multi-function embedded motherboard is integrated with the Intel® HD Graphics 530/510 to deliver stunning UHD 4K resolution and fast 3-D and video playback for graphics-intensive applications. To meet the distinct needs from users, there are six SATA-600 with RAID 0/1/5/10, six USB 3.0, five USB 2.0, four RS-232 ports, two RS-232/422/485 ports, one DisplayPort, one DVI-D, one HDMI and one VGA, as well as has two Gigabit Ethernet ports with Intel® i219LM and Intel® i211AT controllers. To ensure stable and reliable operation, the high-performance Intel® Core™-based industrial micro ATX motherboard supports a watchdog timer and hardware monitoring features. Furthermore, this new embedded board runs well with Windows® 7, and Windows® 10 operating systems.
-
product
Motor Test for Stepping Motors
*Stable measurement: Since it uses Prony braking, this model provides stable measurement unaffected by moments of inertia and no coupling loss. In addition, the resulting measurements allow data correlation via the traditional double-balance method.*Precision measurement method: This model’s judgment of synchronization loss achieves high stability using algorithms developed by Sugawara Laboratories. Measurement mode can be chosen based on step angle. For pull-in torque, startup can be measured consistently from the holding state. Allows measurement at 1-Hz resolution.*Broad measurement range: This model offers a range of seven available measurement heads, from 0.5 N to 50 N, allowing use for high-precision measurements. Through selection and use of pulleys, this model can also be used to measure small motors of 0.5 mN·m or less or 500 mN·m motors. Pulley diameters and other settings are easily configured using a personal computer running Windows®. Note: Any of the seven available heads may be attached to a single measurement component.*High-visibility measurement data: Motor characteristics are easily ascertained on automatically plotted performance graphs. Measurement data can be overlaid up to four times. In addition, the cursor can be used to read accurate values from measurement points. Hard copies of data displayed on-screen can be printed from a personal computer.*Can be controlled using standard personal computers: Allows control of measurement operations and display and storage of data from a standard personal computer running Windows®. Data is stored in CSV-format files for compatibility with other software applications.
-
product
Hand-held 3-Phase Meter Tester
3 Series
Powermetrix continues its industry leadership with the introduction of Powermetrix Remote Manager (PRM) for the PowerMaster® 3 Series. Powermetrix Remote Manager enables wireless control of essential and various metering site accuracy tests contained within PowerMaster® 3 Series from any Windows compliant system up to 100 feet in any environment, including high EMF environments! Customer load Meter Testing, CT/PT ratio testing, CT/PT burden measurement, meter register/demand testing, and wiring verification are all easily performed with this extremely portable, hand-held 3-phase power analyzer. In addition, with the new Model 335, phantom load meter testing and CT burden added testing are available to complete your field-testing needs.
-
product
Digital Random Vibration Controller
DVC8-4 Random
Any of the following plots can be stored on a disk or printed out in color or black and white on any Windows compatible printer.
-
product
CTGcalc™ Software
CTGcalc™ is a Windows application that sets up microwave network analyzers, acquires measured S-parameter data, and analyzes the acquired data for CTG’s various measurement fixtures. CTGcalc™ allows the user to extract complex dielectric permittivity, magnetic permeability, or sheet impedance of the measured specimens.
-
product
Rack Based Test Solutions
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
-
product
PORTABLE OIL TEST
PORTABLE OIL TEST. Test voltage rises up with 3 different speeds. Interchangeable oil cups sit in cradle contacts inside a test chamber with safety high-voltage interlock and hinged grounded metal lid with 2 windows to see the arc across the probes.
-
product
MIL-STD-1553 XMC Interface Module
XMC-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurations - Transformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating availableDesigned for extended temperature operations - x1 Lane PCI Express Host Interface - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
FFT Audio Spectrum Analyzer Plug-in
SPAN Plus
Fast Fourier transform spectrum analyzer. Stereo, mid-side, surround spectrum analyzer. Stereo correlation meter. Multi-track spectrum comparison. PNG spectrum snapshot saving. K level meter. This plug-in is compatible with Windows (32 and 64-bit Windows XP, Vista, 7 and later versions) and Mac OS X (10.5 and later versions, 32-and 64-bit, Intel processor-based) computers.
-
product
Simultaneous Multi-Surface Test Interferometer
VeriFire MST
Simplify the complex – multiple surfaces create complex fringe patterns, the Verifire™ MST uses patented wavelength-shifting technology to acquire phase data from multiple surfaces simultaneously. Report key metrics from individual surfaces of parallel windows, transmitted wavefront, as well as precise surface-to-surface information like total thickness variation (TTV), wedge and even material inhomogeneity.
-
product
DUST CHAMBERS
EDC Series
Free-flow dust circulation centrifugal blower.Uniform floating dust simulation across the test space.Dust pre-heating mechanism for free flow of the dust.Hopper re-vibration for free fall of settled dust.Blower speed regulation to ensure metered uniform dust floating inside the test space.Oil-free vacuum pump to simulate negative pressure for IP6X test.Volumetric air-flow meter/counter for IP6X test.View window with illumination.User-friendly Multi-function programmable timer.
-
product
CableEye Cable Testing
A industry-grade, Windows PC driven cable tester with incredible performance yet amazingly simple to operate. CableEye cable testing has found itself in areas as diverse as working in oil/gas mining through avionics and F1 car testing to audio cables at concerts.
-
product
AINC 429 Multichannel Interface with Additional ARINC-717 Receive & Transmit Channels
DAS-429UNET/RT8-717
The DAS-429UNET/RT8-717 is an ARINC 429, multichannel interface card with additional ARINC-717 receive and transmit channels. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC 429 & ARINC-717 bus, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.The EXC-429UNET/RT8-717 adapter is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application (only versions 8.1 or higher).
-
product
HTTP Sniffer
EffeTech HTTP Sniffer is a HTTP packet sniffer, protocol analyzer and file reassembly software based on windows platform. Unlike most other sniffers, it is dedicated to capture IP packets containing HTTP protocol, rebuild the HTTP sessions, and reassemble files sent through HTTP protocol. Its smart real-time analyzer enables on-the-fly content viewing while capture, analyze, parse and decode HTTP protocol.
-
product
Ultrasonic Tightness Tester
Cygnus Hatch Sure
This portable ultrasonic leak detector is designed to locate leaks and identify seal failures in any closing appliances or compartments, such as weathertight doors on marine vessels or watertight doors (WTDs) or windows on any structures from offshore oil & gas platforms to transportation vehicles.
-
product
Logger version super wide range turbidity sensor with wiper
INFINITY-Turbi ATU75W2-USB
Infinity-Turbi is an autonomously deployable data logger for long-term turbidity measurements. With dual sensors for low (0 to 1,000 FTU) and high (0 to 100,000 ppm) ranges, the instrument can provide Highly accurate turbidity measurements in normal to muddy water. Infinity-Turbi has a mechanical wiper to keep the optical window clean, making long-term observations possible. The instrument has temperature and depth sensors as standard as well, and matches various measuring situations and applications.
-
-
product
PCB Test System
Circuit Wizard - CW409
Qmax Test Technologies Pvt. Ltd.
CW 409 –Circuit Wizard PCB Test System has all the features of QT9627 such as Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test.Maximum Digital Test Speed 10MHz in the QT9627 .It can be connected to any PC/AT or Laptop with Windows 10 operating system through USB Plug and play interface. It operates on user friendly Qmax Test Director software platform with different modes like Test Station for operator level use Test Sequencer mode for Programmer level use and Interactive Workstation mode for quick working.
-
product
SPARK 6U VPX Development System for Cobalt, Onyx and Jade Boards
Model 8264
- 9U 19-inch rackmount, 9-slot, 16-inch deep chassis which houses 6U VPX boards- 64-bit Windows® 7 Professional or Linux® workstation- Intel® Core™ i7 3.6 GHz processor- 16 GB DDR3 SDRAM- ReadyFlow® drivers and board support libraries installed- Out-of-the-box ready-to-run examples
