Product

Mission Data Programmer

MS 1602

-

Meltronics Systemtech

MS 1602 - Meltronics Systemtech

The MIP programmer is used to program, read and erase mission data of Mirage 2000 Aircraft. This system is micro controller based design. This system facilitates to program the four EPROM devices at a time. This system contains four read write slots and one read only slot. Read only slot used to read the device data safely. System also has capability to program the one slot device data to another slot device.

Product

Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)

-

ET System Electronic GmbH

ET System Electronic GmbH

Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)

Product

Programmable AC Power Source

LMX Series

-

Pacific Power Source, Inc.

LMX Series - Pacific Power Source, Inc.

The LMX Series encompasses an all new collection of High Performance 1 phase and 3 phase Linear AC Power Sources. All standard models operate from 15 to 5,000 Hz, range in power from 500VA to 30kVA, and provide nominal output voltage ranges up to 600Vrms L-N.

Product

ISP Programmer Superpro Is01

-

Xeltek

Xeltek

Features:Until now,Support IC manufacturer, pcs devices and keeps growing.1)High speed thanks to the flexible hardware engine. Programming speed adjustable for complicated application environments brought by user target board, length of ISP cable etc.2)Stand-alone and PC-Hosted (USB2.0 High Speed) dual mode;3)Supports ISP programming of devices with I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 and any other serial port.4)ATE interface;5)Over-current and ESD protection to protect your equipment;6)DLL and API for easy integration into customers’ system.Hardware Specifications:1) ISP cable integrates I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 interfaces。2) VDD (0-5.5V /0.5A) and Vpp (0-15V / 0.2A) lines provided to power the target board and the target devices.3) Cable driver circuit supports target devices of voltage level 1.5-5V and is ESD protected.4) USB 2.0 (high speed) interface for PC hosted mode and management of project files on SD card.5) A 20 Characters x 4 lines LCD and a 6-key keypad are built with it for stand-alone operation. In stand-alone mode project files are stored on the SD card (up to 16GB). The number of the project files is limited only by the capacity of the SD card.6) ATE interface is built for easy external hardware control. 6 lines SEL0-SEL5 are for project selection (maximum 64 files); 2 command lines START and STOP; 3 STATUS lines PASS, FAIL and BUSY. All signals are optical-isolated.7) A universal AC adaptor of DC12V/2A is included for power supply.8)WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility.Software Specifications:1) Supports almost all devices with ISP interface.2) Supports Jam and Staple files from ACTEL and ALTERA; Direct C files from ACTEL.3) Programming speed selectable (High, Normal and Low) for complicated applications such as different cable lengths, different target load characters.4) Dynamic buffer function. Application examples include device S/N, MAC address, frequency or transducer calibration etc.5) File format on SD: FAT16, FAT32.6) Functions for IP protection: Project security, SD security, batch control, administration management etc. 7) API and DLL provided for easy integration into customers’ system like ICT and ATE.8) Software provides the features for multiple units to work concurrently controlled by USB HUB.Applications:1)R&D application like in-circuit test and debug.2)Volume production. Devices may be programmed after the board is fully assembled. One example is the serial number writing to an on-board serial device.3)Field application. Comes with portability, stand-alone mode and mobile data storage media (SD card), it is suitable for field test, debug and data acquisition.4)Third application modules. Friend s/w interface (DLL and Virtual Com communication command set) and h/w interface ( ATE and USB) are provided and make it very easy for customers to integrate ISP01 as a functional module into their systems. One example is the ICT equipment. With this integration user can finish in-circuit test and in-circuit programming in one step.

Product

Programmable AC Power Source

6400

-

Chroma Systems Solutions, Inc.

6400 - Chroma Systems Solutions, Inc.

The Chroma 6400 series Programmable AC Power Source uses state of the art PWM technology to deliver pure, instrument grade AC power at a very low cost never achieved before. The 6400 AC power source offers maximum rated power for any output voltage from 0 to 300VAC, at any frequency from 45 to 1K Hz. It is not only suitable for commercial applications (47-63Hz), but also for avionics, marine, military applications at 400Hz.

Product

Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, LL/UL/S/C , Programmable Amplitude Balance

LS-16A-R1-24SLUSC

-

Lumistar Inc.

LS-16A-R1-24SLUSC - Lumistar Inc.

High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.

Product

High Frequency RF and Microwave USB Programmable Signal Generators

LMS Series

-

Vaunix Technology Corporation

LMS Series - Vaunix Technology Corporation

The Lab Brick LMS series of high frequency RF and microwave USB-compatible, synthesized signal generators cover a frequency range from 0.5 MHz - 20 GHz with low noise, fast 100-microsecond switching time, and fine 100 Hz frequency resolution. They require no additional DC supply voltage and offer advanced features such as phase-continuous linear-frequency sweeping, internal/external 10 MHz reference, and optional pulse modulation. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.

Product

Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, LL/S/C , Programmable Amplitude Balance

LS-16A-R1-24SLSC

-

Lumistar Inc.

LS-16A-R1-24SLSC - Lumistar Inc.

High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.

Product

Programmable DC Electronic Load

M97 series

-

Maynuo Electronic Co.,Ltd

M97 series - Maynuo Electronic Co.,Ltd

The new M97XX series programmable DC electronic load is a new generation product designed from Maynuo Electronic Co.,Ltd. Incorporating high-performance chips, the M97XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M97XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications. From 150W to 200KW, there are many models to choose from :

Product

Programmable Setpoint Relay Protection Relay, Trip Relay

CRD-005 and CRD-020

-

Powertek LLC

CRD-005 and CRD-020 - Powertek LLC

CRD-020 Programmable ac current set-point relay setting for threshold levels, over and under-currentoperationbullet CRD-005 Programmable dc voltage and mA set-point relay setting for threshold levels, over and under-voltage operationbullet CRD-005 internal DIP-switches allow for either 0-1mAdc or 0-10Vdc operation, and may be set for under-alarm or over-alarm relay operationbullet CRD-020 internal DIP-switch allow configuration of the ac current range to either 0-5A, 0-10A, 0-15A or 0-20A and the relay mode for under-current or over-current operationbullet Lid mounted two digit numerical push button switch calibrated as percent of full scale with a threshold range of 1-99%bullet Red LED lamp lights to indicate when the threshold level has been tripped