PCI DAQ
Data Acquistion instruments configured to work in a PCI bus.
-
Product
PCIe-6361, PCI Express 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO Multifunction I/O Device
781050-01
Multifunction I/O
PCI Express 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO Multifunction I/O Device - The PCIe‑6361 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Full 4-Axis Motion Control Universal PCI Express Card
PCIE-1245
-
Encoder input: 5 MHz for CW/CCW,P/D,AB mode; Pulse output: up to 5 MHzSupports memory buffer (10 K points) for trajectory planningSupports point-to-point, line and E-Gear; Supports hardware emergency inputCircular and helical interpolation (PCIE-1245 only)Position latch up to 10KHz and memory buffer 1K points (PCIE-1245 only)Position compare triggering up to 100 KHz, and memory buffer is up to 100 K points (PCIE-1245 only)1D&2D plane position compensation (PCIE-1245 only)Gantry mode by semi-closed loop pulse train control (PCIE-1245 only)Dynamic PWM output for velocity following (PCIE-1245 only)
-
Product
PCI Board
SMT835-ZU47DR-2
-
Sundance Multiprocessor Technology Ltd.
The Sundance SMT835-ZU47DR-2 is a PCI express ZynqRF system comprised of the TEB0805 carrier board and the TE0835-02-TXE21-A RFSoC module.
-
Product
PCI To PC104 Extender Board
MS 1717
-
PCI to PC104/EPIC Extender card is used for extending the standard desktop PCI bus to compatible PC104 or EPIC bus. This will help to test all the PC104 cards through standard PC without any embedded processors. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the PC104 or EPIC boards.
-
Product
64-CH Isolated Digital I/O PCI Cards
PCI-7432/7433/7434
Digital I/O Module
ADLINK's cPCI/PCI-743X series cards are 64-CH high-density digital input and/or output cards that provide a robust 2,500 V isolation protection and are suitable for most industrial applications. The wide input range of the cPCI/PCI-7432 and cPCI/PCI-7433 makes it easy to sense the status of external devices. There are several options for PCI-743X series, such as normal version with input range from 0 to 24 V, as well as HIR version with high input range from 0 to 50 V. The PCI- 7433ALC is specifically designed for AC power test system.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 40 MS/s on 8 DAQ Channels and 8 AWG Channels
DN2.803-08
Digitizer
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 1.51MΩ
50-297-144
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Reed Relay Card, 64xSPDT
50-110B-121
-
The 50-110B-121 is a 64xSPDT PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm
50-293-013
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Digital I/O Boards
PISO-813U/S
-
The PISO-813U/S card is the new generation product that ICP DAS provides to meet RoHS compliance requirement. The new The PISO-813U/S card is designed as a drop-in replacement for the PISO-813, and users can replace the PISO-813 by the The PISO-813U/S directly without software/driver modification.
-
Product
PCI Daughter Boards
DB-1825/1/DIN (with DIN rail mounting kit)
-
Screw terminal board using 37 pin cable I/O ports for PCI-1202/1602/1802/822/826 series , (32 channel single-ended ,16 channel differential)Blank pads for break detection, Low-pass filter , current shut and voltage divider (manual soldering)Dimensions :170 mm x 114 mm
-
Product
Intel® Core™ I Automation Computer With 4 PCI(E) Expansion Slots
UNO-3285G
-
Intel® 6th Gen Core™ i7-6822EQ Quad Core Processors with 8GB DDR4 Memory2 x GbE, 6 x USB 3.0, 2 x RS-232/422/485, 2 x RS-232 (pin header), 1 x DVI-I, 1 x HDMI2 x PCIe x8, 2 x PCI, 2 x mPCIe (2 x full), 1x CFast, slot, 1 x mSATA slot (optional)Dual Hot-Swappable storage with thumb screw support for RAID 0/1Supports Fieldbus Protocol by iDoor TechnologyDual power input for power redundancyFront LED indicator design for monitoring system status
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 773kΩ
50-298-043
Programmable Resistor Modules
The 50-298-043 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Digital Signal Processor Card for PCI Bus
SI-C6713DSP
-
The SI-C6713DSP from Sheldon Instruments is a family of powerful Digital Signal Processor (DSP) cards for your PC equipped with a 32 bit PCI bus. It is based on Texas Instruments’ 300Mhz TMS320C6713, 32 bit DSP, and can transform your system into an ultra high performance development platform and DSP accelerator.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 1.02k Ohm
50-293-021
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG-HS
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
PCI Express 5.0 Protocol Exerciser/Analyzer
Summit Z58
Analyzer
The Summit Z58 is a PCIe 5.0 protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z58 can emulate PCI Express 5.0 root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
Product
PCIe-8432, PCI Express, 2-Port, Isolated, RS232 Serial Interface Device
781744-01
Serial Interface
The PCIe‑8432/2 is a high-performance interface for high-speed, port-to-port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial … interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Single CMC size PCI Mezzanine Card
PMC SyncClock32
-
Brandywine Communication’s model PMC-SyncClock32 is a compact PCI Mezzanine Card (PMC) that precisely synchronizes the time on VME cards or provide accurate GPS synchronized time to the host motherboard. The 32-bit interface provides time from microseconds through years.
-
Product
PCI-6229, 32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO PCI Multifunction I/O Device
779068-01
Multifunction I/O
32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO PCI Multifunction I/O Device - The PCI-6229 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Compact PCI Bus Analyzer / Exerciser
CPCI650
-
The CPCI650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
PCI High Density Pecision Resistor Card
50-298-131
Programmable Resistor Modules
The 50-298-131 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 13.6kΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
MIL-STD-1553 One-Channel PCI Board
BRD1553PCI-1
-
The P-Orchestra™ is a one-channel MIL-STD-1553B PCI board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability. The board can be used as a hardware and software development kit for IP cores. P-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 16K word of internal RAM.
-
Product
PCIe-8371, x4 Gen1 PCI Express Host, 832 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
779723-01
Remote Control
The PCIe‑8371 is an MXI‑Express remote controller for devices or systems cabled over PCI from a computer with a PCI Express slot. The PCIe‑8371 remote controller provides a x4 PCI Express link over a copper cable to the PXIe‑8370 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
97 lane, 25 port, PCI Express
PEX 9797
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
Product
Full-Size PCI Express Mini Module With 32 Bit DIO
AX92904
-
*32 bit programmable DIO*Supports four 8-bit TTL level DIO ports with +5V powered*Each bit can be programmable as input or output*51 x 30 mm
-
Product
PCI Data Acquisition Boards
AD8-1500DMA Series - 8 bit, 1.56 GS/s
-
The AD8-1500DMA series has a 1500 MSPS 8-bit A/D, 8GB/16GB of on-board SDRAM memory and the ability to transfer data directly into the computer system's memory at up to 320 MB/s on 64-bit PCI systems. Sampling is controlled by an onboard oscillator or by an external clock input, which may be in the frequency range between 20 MHz and 1500 MHz. Multiple boards may be configured to acquire either concurrently, for more simultaneous acquisition channels, or sequentially, with an automatic overlap selectable from 0 to nearly 2GB, in 512KB steps, for longer record length. Drivers for 64 bit Linux and Solaris operating systems included.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 5.82MΩ
50-298-152
Programmable Resistor Modules
The 50-298-152 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
IEEE488 (GPIC, HPIB) PCI Interface Card - Fits 3.3V or 5.0V Slots, 1KByte Transfer FIFO
GPIB-PCI-XL
-
The GPIB-PCI-XL is a PCI GPIB controller card that converts any PC with a PCI bus slot into a GPIB controller.
-
Product
DAQ Modules
Q.series X DAQ Modules for EtherCAT
-
All Q.series X DAQ systems possess the same measurement capabilities and performance. The main differentiating factor between the XL and XE versions of Q.series X is the Fieldbus communication protocol, which can be interchanged on Q.series X modules using a simple firmware update.
