PCI DAQ
Data Acquistion instruments configured to work in a PCI bus.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 65.5k Ohm
50-294-033
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXIe-8383MC , x8 PCI Express 2.0, PXI MultiComputing Remote Control Module
782971-01
The PXIe‑8383mc is an adapter module that allows two or more intelligent systems to exchange data via PCI Express. Because of the excellent data transfer characteristics of PCI Express, the PXIe‑8383mc enables PXI systems to transfer data at multi-gigabytes per second of practical data throughput with only a few microseconds of latency.
-
product
32-bit / 33 MHz PMC to PCI Adapter
4933
This PMC to PCI Adapter product from Technobox permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
product
PCI Express 4-Channel Frame Grabber with Audio Capture
811
4 composite/S-Video + 4 stereo audio input channels Simultaneously captures on all channels Captures raw RGB or YUV video 4 general-purpose digital I/Os configurable as inputs or outputs
-
product
PCI Fault Insertion Switch Range for Differential Serial Interfaces
50-200/201
Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN and FlexRay, and the High Bandwidth Differential PCI Fault Insertion Switch (model 50-201) which is designed for higher data rate serial interfaces such as AFDX and 1000BaseT Ethernet. Each module allows the introduction of fault connections that include data paths open, data paths shorted together, and data paths shorted to externally applied faults such as power supplies and ground. The software driver defaults to a protective mode where conflicting faults are prevented to avoid accidentally shorting unintended paths, such as power to ground. A separate mode allows complete freedom in setting fault patterns.
-
product
14-Bit PCI Express Digitizer
SIS1160-SFMC01
The SIS1160-SFMC01 is the combination of the SIS1160 carrier with the SFMC01 2 channel 2.5 GSPS 14-bit digitizer FMC.
-
product
Circuit Module, Riser for ISMB 2U PCIe X16 Riser Card to 2 PCIx8 Expansion Slots , and PCI card
AIMB-RP3P8-12A1E
Support ISG 2U chassis
-
product
PCI Mezzanine Card
PNIC1G
Each Ethernet interface supports 10, 100 and 1000 Mbits transmission rates with auto-negotiation for full duplex operation; 10 and 100 Mbit/s transmissions for half duplex operation, and is equipped with a 32 Kbit Serial EEPROM.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 773kΩ
50-298-043
The 50-298-043 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Windows Driver & SDK for ADLINK USB DAQ Series Data Acquisition Modules
UD-DASK
ADLINK DASK drivers are the device drivers for custom data acquisition applications for Windows. The DASK driver libraries provide API sets for ADLINK PCI ExpressR, PCI, CompactPCI, PXI and USB data acquisition cards, to access full hardware functionalities, such as buffered/double-buffered data acquisition, pattern generation, digital input/output and etc. For novice users, the built-in CodeCreator utility helps you create your first program in just a few minutes.
-
product
81 lane, 21 port, PCI Express
PEX 9781
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
product
PCIe-6320, PCI Express, 16 AI (16-Bit, 250 kS/s), 24 DIO Multifunction I/O Device
781043-01
PCI Express, 16 AI (16-Bit, 250 kS/s), 24 DIO Multifunction I/O Device - The PCIe‑6320 offers analog input, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6320 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PCI Data Acquisition Boards
Ultraview''s PCI data acquisition add-in cards are complete data acquisition (A/D) and control (D/A) systems on a single PCI Bus card. Ranging in speed from dual 14 and 12-bit 1-25MSPS boards up to 1500MSPS 8-bit boards with 8GB/16GB of on-board RAM. All cards come with graphical waveform viewers, example user programs (source code included) and device drivers for Linux or Solaris, allowing users to quickly prototype and develop their applications.
-
product
USB Data Acquisition (DAQ) Products
ACCES now offers USB-based data acquisition and control in both standard packaging and embedded OEM USB/104 board only options. These USB DAQ devices are perfect for a variety of applications requiring monitoring, control and industrial serial communications. USB is by far the most popular and compatible standard data interface for direct PC connection. Add the features you need in your application in hours, not days. Choose from over 100 different models and options (including extended temperature) encompassing analog I/O, digital I/O, counter/timer, and serial I/O configurations. Experience simple and immediate connection to any PC or embedded system with a USB port.
-
product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
product
PCI 50xDPST Reed Relay Card
50-115A-122
This is the 50xDPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
product
12-Lane, 5-Port PCI Express
PEX 8714
The ExpressLane™ PEX8714 is a 12-lane, 5-port, PCIe Gen3 switch device developed on 40nm technology. PEX8714 offers PCI Express switching capability that enables users to connect a host to the endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 102kΩ
50-298-040
The 50-298-040 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 102kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Shared Memory Network PCI Express Interface
PCIe-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodesNetwork interrupts supported - PCIe 2.0 (x4) CompliantSoftware Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
-
product
PCI High Density Potentiometer Card 5-Channel, 8-Bit, 0 To 255 Ohm
50-296A-021-5/8
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Express A/D Board
AD12-2000 - Dual 12 bit, 2 GS/s, up to 7GB/s DMA
The AD12-2000 series has two 2000 MS/sec 12-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at up to 7 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, at twice the effective memory depth and speed (up to 4 GSPS).
-
product
RTSI Bus Cables for 5 PCI or AT/ISA Devices
776249-05
34-Pin Female RTSI to 34-Pin Female RTSI Ribbon Cable - The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
product
6U Compact PCI Single Board
CP62005
LinkedHope Intelligent Technologies Co.,Ltd.
CP62005 is a 6U CompactPCI® single board with high-performance, low power consumption and high reliability. It is ideal for ruggedized systems requiring high-bandwidth processing, or for information processing and embedded computing.CP62005 supports 4th generation Intel® Core™ i7 or i5 Haswell processors, up to 16GB onboard DDR3L memory. It also offers 16GB onboard SLC SSD for operating system and drivers. The onboard design of memory and SSD can enhance the anti-shock and vibration performance.CP62005 integrates Intel® HD Graphics 4600 controller, which supports a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA… CRT max resolution is up to 2048x1536. With HDMI/DP/eDP it can be up to 4K. It also supports three independent displays.
-
product
Dual PCI Express, Hot-Plug Controller
MAX5946A, MAX5946L
Dual-Slot, Hot-Swap Controller Enables Safe Insertion and Removal of PCI Express Cards
-
product
16 Channel ADC for PCI
PCI392
The PCI392 16-Channel Common-Mode Input ADC for PCI is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs all functionality like calibration. User-specific functions can be added for customized operation.
-
product
PCI Express Full Tx Test Suite
SW02PCIE
The PCI Express Full Tx Test Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. In addition to Tx Validation licenses for PCIExpress, this suite also provides the support of the Advanced PCIe Protocol Decode/Trigger Software. This suite supports coverage across the PCI Express technology starting from Gen4. Together with the subscription model, this enables the support and coverage continuity as the PCI Express technology progresses through generations.
-
product
PCI Express, IEEE 488 GPIB Instrument Control Device for Windows
778930-01
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
