PCI DAQ
Data Acquistion instruments configured to work in a PCI bus.
-
Product
PCIe-8430, PCI Express, 8-Port, RS232 Serial Interface Device
780591-01
Serial Interface
The PCIe‑8430/8 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard … COM ports for compatibility with programs that use serial communications.
-
Product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
-
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
Product
PCI Synthesizer
SYNTH300 Series
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-A429 and ECD54-A429
Interface Card
Alta Data Technologies’ PCCD-A429 & ECD54-A429 interface modules offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.
-
Product
Fluke DAQ 6.0 Application Software
-
Fluke DAQ 6.0 is a powerful, versatile data acquisition application that provides effortless configuration, data logging, and analysis for the 2680A and 2645A NetDAQ Networked Data Acquisition Unit » and 2680 Series Data Acquisition Systems », plus adds support for the Fluke 2638A Hydra Series III Data Acquisition System/Digital Multimeter » and Fluke Calibration 1586A Super-DAQ Precision Temperature Scanner ».
-
Product
16 Channel ADC for PCI
PCI392
-
The PCI392 16-Channel Common-Mode Input ADC for PCI is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs all functionality like calibration. User-specific functions can be added for customized operation.
-
Product
PCI Express Waveform Digitizer
ATS9625
-
ATS9625 is a 250 MS/s 16 bit PCI Express waveform digitizer with an on-board, user-programmable FPGA. With fixed ac-coupled input range of 2.5 Vp-p and signal to noise ratio in excess of 75 dB, ATS9625 is an ideal solution for radio applications.
-
Product
XMC-to-PCI Express (PCIe) Adapter
8366
-
The Technobox, Inc. P/N 8366 Compact XMC-to-PCIe (PCIe) adapter permits use of a standard VITA 42.3 air-cooled XMC in the smallest possible edge finger PCIe form factor. The length of the adapter is the length of the XMC, while the height is a standard PCIe board, not the low-profile version. It provides up to eight lanes (8X) from the XMC's P15 connector to the edge fingers.
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8462
-
The Technobox, Inc. P/N 8462 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
Product
6U Compact PCI Single Board
CP62005
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62005 is a 6U CompactPCI® single board with high-performance, low power consumption and high reliability. It is ideal for ruggedized systems requiring high-bandwidth processing, or for information processing and embedded computing.CP62005 supports 4th generation Intel® Core™ i7 or i5 Haswell processors, up to 16GB onboard DDR3L memory. It also offers 16GB onboard SLC SSD for operating system and drivers. The onboard design of memory and SSD can enhance the anti-shock and vibration performance.CP62005 integrates Intel® HD Graphics 4600 controller, which supports a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA… CRT max resolution is up to 2048x1536. With HDMI/DP/eDP it can be up to 4K. It also supports three independent displays.
-
Product
PMC Carrier for PCI Card Interface
TPCI270
-
The TPCI270 is a standard 33 MHz, 32 bit PCI carrier for a single PMC Card. Itprovides PMC front I/O and PMC P14 rear I/O. This PMC to PCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in standard PCI systems.
-
Product
Stepper Motor Controller for PCI
PCI322
-
The PCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785650-01
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
Product
12 Port PCI Express
PEX 8615
-
The ExpressLane™ PEX 8615 offers 12 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 12 flexible ports and fully conforms to the PCI Express Base Specification, rev 2.0. PEX 8615 architecture supports a high-performance DMA engine with four DMA channels and internal buffer space for internal descriptor support. Up to 256 descriptors are supported internally or alternatively descriptors can also exist in host memory.
-
Product
24-Port PCI Express
PEX 8796
-
The ExpressLane™ PEX8796 is a 96-lane, 24-port, PCIe Gen3 switch device developed on 40nm technology. PEX8796 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
PCIe-8430, PCI Express, 2-Port, RS232 Serial Interface Device
782122-01
Serial Interface
The PCIe‑8430/2 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard … COM ports for compatibility with programs that use serial communications.
-
Product
Analog Output DAQ Cards
-
Analog output cards are ideal for DAQ applications where multiple A/O channels are needed for voltage and current output.
-
Product
PCI Precision Resistor Card 6-Channel, 3Ω To 2.97MΩ
50-297-051
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Matrix, Single 22x4 1-Pole
50-510A-021
Matrix Switch Module
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
PCI 32xSPST Shielded Reed Relay Card
50-125-021
Reed Relay
The 50-110/115 range of PCI shielded switching cards are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
PCI D/S, S/D, I/O & Comm Board
76CS3
Multifunction I/O
NAI’s 76CS3 is a PCI/PCIe multifunction I/O and communication board designed for applications requiring Digital-to-Synchro/Resolver (D/S) and Digital-to-LVDT/RVDT (DLV) stimulus output, as well as I/O and communication functions. This full-slot board contains five independent, function module slots. The board can be configured for 6 separate D/S channels, or for D/S in combination with I/O and communication modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm
50-293-023
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Express PoE Card
AX93330
-
The AX93330 PoE (Power over Ethernet) card supports 4 independent 10/100/1000BaseT 802.3AT compliant Ethernet ports. It provides 48VDC at PoE ports and has wide temperature from -40°C ~ 85°C on module. It allows power to be supplied to connect devices that allows IP telephones, wireless LAN Access Points and security network cameras.
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 395kΩ
50-297-142
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Counter/Timer with Quadrature Board
APC484
-
Several models with a variety of configurations provide up to ten counter/timer channels for counting events, generating waveform control signals, measuring pulse-widths, periodic rates, or quadrature position and monitoring operations.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 31.5Ω
50-298-010
Programmable Resistor Module
The 50-298-010 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Digital I/O Cards
-
Sealevel PCI digital I/O cards are available with optically isolated inputs and Reed relay outputs. For high-voltage requirements, TTL versions provide convenient connections to industry-standard solid-state relay racks. Sealevel low profile PCI digital I/O boards meet the requirement for the MD1 low profile specification and feature Universal Bus (3.3V and 5V) for compatibility with both new and legacy computer systems.
-
Product
PCI Very High Density Multiplexer, 99-Channel, 2-Pole
50-670C-022-99/2
Multiplexer Module
The 50-670C-022-99/2 is a 99-channel, 2-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PCI Bus Analog Output Board, 8 Isolated Outputs, 14 Bit
APCI-3501-8
-
*8 analog output channels*Optical isolation 500 V*Settling time 30 µs typ.*14-bit resolution (13 bit for 0-10 V)*Output voltage: ±10 V, 0-10 V (switchable through software)*Output voltage after reset: 0 V*Each output channel has its own ground line (without optical isolation from the others)*Driver capacity: 5 mA/500 pF*Short-circuit protection, EMI filters*Noise neutralization of the PC supply*Creeping distance: 3.2 mm acc. to DIN VDE 0411-100*Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary*2 digital input channels, 24 V, isolated*2 digital output channels, 24 V, isolated
-
Product
XMC-to-PCI Express Adapter
7988
-
The Technobox, Inc. P/N 7988 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 7988 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
