-
Product
Incremental Length Gauges For Measuring Stations And Multipoint Inspection Equipment
CERTO series
-
*Interferential scanning principle*Very high system accuracy of down to ±0.03 µm*Well-matched ball-bearing guide for very high quality*Defined thermal behavior*Large measuring ranges of up to 60 mm*Interface: 11 µAPP
-
Product
Weld Gauge
147
-
The Elcometer 147 Weld Gauge measures many aspects of welds in both Metric and Imperial units.
-
Product
Digital Refrigerant Gauges
-
Our wireless digital manifolds are designed to measure a wide range of parameters in refrigeration, cooling and heat pump systems, including pressure, evacuation and overheating, as well as undercooling for over 100 different refrigerants.
-
Product
Portable Hydrostatic Hose Tester, 15000 psi; USMC
9901HT-8762
-
The 9901HT-8762 Hydraulic Hose Test System is utilized by the United States Marine Corp. for their portable forward base maintenance stations. The system includes it's own onboard "quiet" air compressor and a set of 37 degree flared test adapters from 3/16" through 2" as well as an onboard calibration gauge and pneumatic castors for use on rough terrain.
-
Product
Digital Strain Gauge Sensor
ZET 7111
-
The ZET 7111 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or separate external tension gauges connected using half-bridge or bridge scheme.
-
Product
ConFigXP
-
AMETEK Sensors, Test & Calibration
ConFigXP is free software to customize your XP2i digital pressure gauge to fit your application. You can add features and special modes, remove features to simplify the gauge, and complete password protected tasks, like calibration adjustment.
-
Product
Instrument Grade Data Sensor
WISER 8000
-
TECAT Performance Systems, LLC
The TECAT WISER Model 8000 dual strain measurement and monitoring system is a wireless data acquisition system for measuring two external strain channels at high data rates up to 8kHz. The small, light, power-efficient, and non-invasive design enables strain measurements in a wide range of applications. With dual external sensor inputs two Micro-Measurements strain gauge bridges can be measured by a single system, for example to measure both thrust and torque loads simultaneously.The Model 8000 has a long range data transmission of >1,000 meters with up to +/- 0.025% FSR sensitivity for remote measurements. After initial setup using the WISER software interface, the system can be wired directly to your DAQ system, for seamless data collection.
-
Product
PCI Strain Gauge Simulator Card, 6-Channel, 1.5k
50-265-406
-
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Digital Gauge Counter with Comparator Function
DG-4320/4340
-
The DG-4320/4340 Digital gauge counters display and calculate the measured values from linear gauge sensors.In addition to four basic functions (Multiplication switching, factor setting, offset setting and number of decimal place setting), new features such as calculation display function and condition memory function are equipped. It helps in-line measurement to work at production site efficiently.
-
Product
Deep-Bore/Spherical Diameter Gauging
XT Spherical
-
• 2 point (ovality) available from 3mm, 3 point available from 6mm• 6-300mm range, 300-500mm XT500 System• Guide sleeves available, 2 point to maintain centralisation, 3 point to protect the head/bore• Allows for misalignment in bore• XT, Ultima• Ease of use for operator• Interchangeable with standard heads• Blind Bore option available
-
Product
Strain Meters
-
Omega offers a large selection of Strain Meters for all strain gauge and load cell applications. All of our Strain Meters are built to deliver exceptional and accurate performance over the long-term.
-
Product
Needle Microprobe
MT-26/2HT
-
Fast-response 26 gauge needle probe, (needle length is 2 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Industrial Pressure Calibrator
2271A
-
The Fluke Calibration 2271A Industrial Pressure Calibrator provides a complete, automated solution for calibrating a wide variety of pressure gauges and sensors. Thanks to its modular design, it can be configured to meet different needs and budgets, and expanded to cover a broad workload. The 2271A is ideal for calibration laboratories starting out in pressure calibration because it offers wide pressure measurement capabilities in a single instrument. Everything you need for calibrating pressure is included; just connect supply pressure. And your investment will stand the test of time: as your workload grows and changes, the 2271A can grow and change too. Just add measurement modules.
-
Product
Force Gauges
-
A digital force gauge, often called a push pull force gauge or tension and compression force gauge, is used in material testing, quality control and assurance, research, development, product testing, laboratory and educational applications. PCE Instruments' (PCE) digital force gauge products are the benchmark of quality and performance. PCE digital force gauge devices provide measurements in kilograms (kg), grams (g), ounces (oz), pounds (lbs) and Newtons (N) of force (f), depending on the force gauge model. Most PCE digital force gauge products are handheld, portable devices that also can be used with a universal test stand. There are several different force gauge products available online in the PCE web shop.
-
Product
IEC60529 Ipx6 Water Spray Nozzle
CX-IPX5-6
-
Shenzhen Chuangxin Instruments Co., Ltd.
IPX5/IPX6 Jet Nozzle Test consists of a jet handle that is equipped with a pressure gauge and an easy-to-adjust flow valve.
-
-
Product
Input Terminal Block For Digital Multimeters
34171B
-
The Keysight 34171B DMM input terminal connector block is a set of two connectors which provide a convenient and reliable method to connect wires to all five input terminals. Terminals are made of low-thermal copper alloys to minimize thermally-induced voltages caused by dissimilar metals. For minimum thermal offset voltages, use unplated copper wire of the same gauge for all connections.
-
Product
Pressure Controllers & Transducers
-
Alicat Scientific, Incorporated
Fast pressure controllers keep your process stable and repeatable. Alicat offers pressure controllers for use in flowing, dead-ended, or vacuum applications. Dual-valve models for closed volumes eliminate the need to continuously bleed expensive process gases. Instruments are available with absolute, gauge, or differential pressure sensors for pressure control as high as 3000 PSIA/PSIG (or 150 PSID) and as low as 2 inH₂O.
-
Product
Robotics and Machine Vision Standards
-
Accuracy in machine vision systems is critical to achieving strategic goals regarding quality, efficiency, and consistency. Use our ACCUplace product lines to calibrate vision systems’ distortion, placement/alignment, or other field parameters in systems used for guidance, identification, gauging, and inspection. Using our specialized ACCUedge® technology, our Robotic and Machine Vision Standards are manufactured with line-edge quality that is second to none in the industry, providing the precision needed to calibrate almost any system. Should you need to alter feature patterns, size, or substrate to fit your needs, fill out our Optical Components and Standards form to start the conversation.
-
-
Product
Distance Gauge
LOCalizer
-
LOCalizerTM from Faxitron® is the revolutionary way to guide breast surgeries easily and accurately. LOCalizer uses a miniature radiofrequency Tag designed to be implanted into the breast up to 30 days before surgery. No surgical wires mean less stress for your patients and no more localization scheduling conflicts for you and your team. LOCalizer gives you the precision you need without the drawbacks of other localization techniques.
-
Product
Fuel Injector Tester GM Multiport
FIT457
-
For GM domestic cars with large schrader adapters; light trucks, vans and sport utility vehicles with multi-port. The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
Product
High Temperature, Pressure Data Logger
PR140
-
The PR140 is built with a precision stainless steel pressure gauge. The data logger has an accuracy of ±0.03 Bar (±0.435 PSI), which can be achieved over a wide temperature range, from 20°C to +140°C(68°F to 284°F). The PR140 can be programmed to take readings as often as once per second (1Hz), and has non-volatile memory that can store up to 32,700 measurements.
-
Product
Tool, Inspection Depth Gauge, Micro Coax, ITA
910121180
-
Tool, Inspection Depth Gauge, Micro Coax, ITA.
-
Product
CAN MiniModules
CAN STG6 MiniModule
-
Precise measurement of mechanical strain, directly at the point of application of the strain gauge: realized via the CAN-based measurement module STG6 BK10 with six strain gauge inputs for quarter-, half- and full bridges.
-
Product
Needle Microprobe
MT-4
-
Fast-response 29 gauge needle probe with blunt tip, (needle length is 1cm) for instant readings. Good for instant skin temperature and surface temperatures, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44P2
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Universal (ID/OD) Presetting Instruments
-
Pratt & Whitney Measurement Systems, Inc.
If gage setting and calibration is important to you, choose the Labmicrometer Model 900 or 1600 measuring system. Designed for gage calibration laboratories and shop floor environments requiring precise internal and external measurements over long lengths. Additionally, the Labmicrometer is ideal for use as a setting bench and adjusting instrument offering precision setting of inside and outside comparative measuring gages, micrometers, snap gauges, as well as other measuring tools.
-
Product
Altitude and Vacuum Chambers
A series
-
Bemco's acclaimed Altitude and Vacuum Chambers are designed to meet the need for a combination, easy to use altitude testing chamber, and ruggedly built vacuum processing facility. Today's modern A series chambers feature another Bemco first, a standard Brooks Automation, Granville-Phillips Series 375 Convectron Gauge Controller.
-
Product
Foot Valve Dispensers
-
Foot Valve Dispensers, the TS924 and TS924V dispensers are floor mounted, have a built in pressure regulator, pressure gauge and a unique fast-dump, three-way air valve. Perfect for areas where electricity is prohibited.
