Repeaters
-
Product
Radar Target Repeater
Series 8000
-
The Eastern OptX Series 8000 Radar Target Repeater is a portable, variable delay and propagation loss system designed for radar testing and alignment. The repeater may be remotely programmed in the field for dynamic operation. When connected to a user specified antenna the repeater can provide delays of up to 500 usec with a fixed delay, multiple discrete delays, or a progressive variable delay with amplitude control The Series 8000 features ultra wide bandwidth, low loss, high isolation, low noise figure, and high dynamic range.
-
Product
Drop Testers
-
This process is vital for ensuring that products travel to customers safely and securely, eventually arriving damage free. In turn, drop test systems help companies save money and maintain positive brand-owner reputations by helping to design packaged products that will deliver products with their intended inherent quality intact. Lansmont Drop Test Systems are the gold standard for accurate and repeatable drop testing. Every drop tester we manufacture is factory-tested to ensure it meets flatness-of-drop requirements and exceeds industry specifications.
-
Product
Programmable Step Attenuator DC~50GHz, 0~115dB Att.
-
The programmable step attenuator achieves step attenuation over a wide frequency band. It features high attenuation accuracy, excellent repeatability, low insertion loss, and long service life. Its primary applications include controlling the amplitude of signals entering systems, regulating output signal power in systems, and adjusting impedance matching between signal sources and loads. It is widely used in various broadband spectrum analyzers, broadband vector network analyzers, broadband synthesized signal sources, noise figure test sets, and diverse microwave automatic test systems.
-
Product
Pil Dielectric Test Sets
DTS Series
-
The DTS Series provides repeatable and accurate measurements of the breakdown voltage of insulating oils used in electrical equipment. The DTS-60D & DTS-100D offer 60 kV AC and 100 kV AC output respectively. They include three user-selectable, automatic voltage rates-of-rise, and automatic voltage shutdown with the meter indicating the flashover voltage. Various test cells are available.
-
Product
Motorised and Automated Probe Heads
-
Motorised heads enable automated, repeatable re-orientation of probes to allow access to features on all faces of the part, improving the capability of the CMM and maximising productivity.
-
Product
LED tester
-
Ecopia's LED tester is good to measure both electrical(I-V curve) and optical(Spectra, Light intensity) properties of LED chip, LED lamp, SMD type at the same time.It also makes it possible to see LED sample's construction , seeing through microscope. LED tester main body flow input current ,and emitted light from the LED sample is focused on lens of microscope.From this process, our LED tester can provide repeatable tested results and minimize error values and improve convenience of how to use.
-
Product
Spring Testers
-
Imada offers manual or motorized spring testers in vertical or horizontal configurations.Lever-operated manual systems enable rapid compression and tension spring testing.Wheel-operated manual systems enable slower, more precise movement with the hand wheel.Motorized compression testers offer the most control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All spring testers can be configured with a digital force gauge with data output for analysis by data acquisition software. An optional digital distance meter to measure displacement is available.
-
Product
High-acceleration Shock Tester
DP-1200-18
-
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
Product
Mid-Range Chemiluminescence Oxides of Nitrogen Analyzer
Model T200M
-
The Model T200M combines the proven chemiluminescence principle with a number of innovative features to provide reliable and repeatable NO, NO2, and NOx measurements for extractive type CEM systems. The option of either a molybdenum converter or a high-efficiency stainless steel thermal NO2 converter allows the T200M to be used in a variety of extractive CEM systems, from gas turbines to coal-fired boilers. The T200M may be fitted with an optional, internal paramagnetic O2 sensor or an infrared absorption CO2 sensor, reducing integration and operating costs significantly.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T200M comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
PXI/PXIe RF Multiplexer, Dual 8-Channel, 3GHz, 75Ω, MCX
40-834A-102
Multiplexer Module
The 40-834A-102 (PXI) and 42-834A-102 (PXIe) are 75 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-834A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
Automatic Online Flatness and Surface Appearance System
UltraSort200
-
The UltraSort continues our 25 year tradition of providing metrology solutions to semiconductor wafer manufacturers. Designed for volume wafer production, this automated system offers superior performance in rapid, repeatable, accurate, noncontact qualification of silicon and alternative substrate wafers.
-
Product
EMI Shielding Effectiveness Testing
-
Eurofins E&E North America can easily develop sound engineering measurement techniques to quantify the SE of your product. Our process involves creating detailed SE Test Plans used to insure accurate and repeatable test results.Eurofins a has years of experience to assure our customers that the evaluation reflects the electrical attenuation performance of the material. Often times, our test report becomes supporting documentation for our customer’s end-user contractual requirement, where Independent Test Laboratory results verify the electrical performance of the material being tested.
-
Product
2:8 A/B Splitter
XPD-28
-
XPD-28 splitters boost, refresh and distribute the DMX signals of two inputs onto eight outputs. This allows for safely going beyond the 32 devices limit of the DMX standard, as well as for building star topologies. Moreover, the XPD-28 can be used as a repeater in order to transport a DMX signal across larger distances just as well.
-
Product
PXI Dual 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX Terminated
40-876-102
Multiplexer Module
The 40-876-102 is a 50 Ohm 4 to 1 RF multiplexer with 2 banks in a single PXI slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40-876 has been minimized by careful attention to the mechanical and electrical design.
-
Product
Calibrated Solar Reference Cell
-
To insure repeatable testing on any solar simulator, OAI offers 2cm x 2cm calibrated reference cells. Standard reference cell calibration cycles can be set up by OAI''s calibration laboratory to insure that your reference cell maintains certification.
-
Product
Broadband Optical Source - MATRIQ
Optical Source
Our SLED MATRIQ instrument is a compact super-luminescent LED light source with high output power, large bandwidth and low spectral ripple.The SLED comes in various wavelength models to address various key applications across telecom and datacom, and is ideal for building a customized optical testing platform that delivers reliable and repeatable results.
-
Product
PXI Quad 4 to 1 RF MUX MCX 75 Ohm
40-832-104
Relay
The 40-832-104 is a 75 Ohm 4 to 1 RF MUX with 4 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Broadband Antenna
Vivaldi
-
The dbDIRECT Broadband Antenna features a broad frequency range of operation, high gain, small form factor and directional radiation pattern, making it highly attractive for widespread use in test and measurement of emerging wireless technology devices and radars. Contrary to conventional Vivaldi antennas limited to operating only at higher frequencies, the dbDIRECT Broadband Antenna design is optimized to operate at a frequency as low as 700 MHz up to 6 GHz. This lightweight and compact antenna design provides excellent matching over a broad frequency range.The antenna is designed to be placed in a DVTEST's portable anechoic chamber such as the dbSAFE enclosures for OTA (Over the Air) testing of DUTs. The antennas can be mounted in fixed positions to facilitate repeatable results. When used in conjunction with a rotary positioning mechanism, customers are able to detect the highest point of power sensitivity for enhanced accuracy and repeatability in measurements. In this configuration, both the antennas and DUTs can be positioned in order to facilitate the measurement.
-
Product
PXI Quad 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX
40-872-104
Multiplexer Module
The 40-872-104 is a 50 Ohm 4 to 1 RF MUX with 4 banks in a single PXI slot. It exhibits low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Winding Resistance Meter
TRM 25
-
SCOPE introduces 25 A state of the art precision winding resistance meter, specially designed for field testing as well as factory testing of large transformers up to 500 MVA. Winding resistance value of transformer and rotating machine are directly displayed on 5.7” TFT display. TRM 25 is designed to work in live EHV switchyard conditions, ensuring operator’s safety and repeatability of results. Maintenance time saving is ensured by one time connection to transformer with simultaneous resistance measurement of three / six windings, measurement of resistances of all taps with automated tap change and demagnetization facility. The meter is protected against the back-EMF offered by large inductive windings.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, SMB
40-835A-001
Multiplexer Module
The 40-835A-001 (PXI) and 42-835A-001 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
VNA Calibration Kits
-
Vector Network Analyzers are commonly used to accurately determine the RF Characteristics of microwave components. Accurate Testing of microwave circuits means eliminating measurement errors and ensuring repeatable results. This is only possible when the network analyzers can be calibrated with known and true calibration standards.
-
Product
Topside Probing for Functional Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.
-
Product
Spectrocolorimeter Instruments
-
Shenzhen ThreeNH Technology Co., Ltd.
The ultimate tool for precision color measurement, 3NH's range of spectrocolorimeter instruments adopts a CMOS dual-channel spectral sensor and is equipped with a Φ8mm platform measurement aperture. It has excellent repeatability and inter-instrument agreement.
-
Product
Universal Gauging
-
To improve the quality of your large diameter machined parts, the portable Universal Setting Gauge from Bowers has been developed as an easy to use comparator tool which can be set up next to the gauge being utilised. This Universal Setting Gauge has been designed to improve the ongoing accuracy levels; when setting the master, the spring loaded setting anvil ensures a constant force is maintained thereby giving repeatable setting readings. The Bowers Universal Gauge’s ingenious modular format enables it to be quickly configured to suit almost any measuring challenge.
-
Product
Atomic Oven
-
Atomic oven with collimated output for ultra-high vacuum systems, loaded with Sr, Yb or Ca. The oven provides superior heat isolation while achieving high atomic flux. Its low power consumption results in exceptionally low pressures during normal operation for temperatures up to 650 °C. The chamber is shipped in an ultra-high vacuum storage chamber supplied by AOSense. Customers can provide AOSense with a previously purchased storage chamber for repeat orders. Please contact us for more information.
-
Product
X-ray Fluorescence Sulfur/Chlorine-in-oil Analyzer
MESA-7220V2
-
The MESA-7220V2 measures both sulfur and chlorine in petroleum based products using the Monochromatic Energy Dispersive X-ray Fluorescence (EDXRF) method. A monochromatic X-ray source is used in order to obtain an ultra-low noise background which affords the best detection limits for both sulfur and chlorine.The detector window size was increased to collect more fluorescent X-rays and thus achieve lower level ppm values. This provides excellent, repeatable performance at both low and high concentrations of both elements.By adjusting the angle of the graphite crystal, the excitation beam can be measured to excite sulfur in the sample, increasing sensitivity.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 50Ω, SMB
40-872A-001
Multiplexer Module
The 40-872A-001 (PXI) and 42-872A-001 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40/42-872A has been minimized by careful attention to the mechanical and electrical design.
-
Product
Fuorescence LED Illumination System
pE-2
-
The pE-2 is a fluorescence LED illumination system which provides repeatable and controllable light with a choice of 20 different LED peaks. It is perfect for the researcher who has a specific set of tests to conduct. The user can specify a wavelength configuration matched to their particular fluorescence requirements. It is modular, allowing LED wavelengths to be exchanged as requirements vary or additional experiments are added. Manual control is via a remote control pod with instant on/off and intensity control from 0-100%. Additionally, the system is fully integrated under many imaging software packages.
-
Product
Standard Mass Flow Meter
Series II
-
Offers outstanding value in a wide range of industrial and lab applications. Exceptional accuracy and repeatability with flow ranges from 0.014 cc/min up to 1670 l/min. and working pressures up to 6000 PSIA. Offers multi-gas and multi-range capability
