-
Product
Machine Vision System for Magnetic Luminescent Control of Wheels
-
The machine vision system of the wheel magnetoluminescent control unit is designed to automate the technological operation of the magnetic luminescent control in the production of railway wheels with full-profile mechanical surface treatment. The system is a hardware and software complex for presenting complete information on the tested wheel to a flaw detector operator, automatic detection of potential defects, maintaining a control protocol and interacting with the installation controller and the line database.
-
Product
S Sensor
Z-Gard S Sensor
-
The Z-Gard S Sensor is designed to detect the presence of carbon monoxide, nitrogen dioxide and combustible gases in air. These sensors employ solid state, electrochemical or catalytic sensors which generate a representative output signal proportional to the calibrated operating range.
-
Product
8-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB208
-
The FAB208 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, and a total of six 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB208 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110. We have two enclosures, the AX60551 and AX60552, to house the backplane.
-
Product
PCI-6519, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Sink Outputs, Bank-Isolated Digital I/O Device
779085-01
Digital I/O Module
The PCI-6519 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6519 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6519 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
Strength Meter
NOVOTEST IPSM-U+T+D (Pulse Velocity Tester)
-
The pulse velocity tester IPSM-U+T+D allows to measure the strength and homogeneity of the concrete, bricks and other materials under the composition and surface sounding in products and designs for construction projects, inspection of buildings and structures, according to ASTM C597-16 (Standard Test Method for Pulse Velocity Through Concrete). Has the determining of the depth of cracks by the surface sounding probe function and also flaw detection mode (A-scan).
-
Product
Ultrasound Measurements
-
Is sound waves with frequencies higher than the upper audible limit of human hearing. Ultrasound is no different from 'normal' (audible) sound in its physical properties, except in that humans cannot hear it. Ultrasound devices operate with frequencies from 20 kHz up to several gigahertz.Ultrasonic devices are used to detect objects and measure distances. Ultrasound imaging or sonography is often used in medicine. In the nondestructive testing of products and structures, ultrasound is used to detect invisible flaws.
-
Product
Sensors
-
A sensor is a device that produces an output signal for the purpose of sensing a physical phenomenon. In the broadest definition, a sensor is a device, module, machine, or subsystem that detects events or changes in its environment and sends the information to other electronics, frequently a computer processor.
-
Product
Gas Sensors
-
Advanced Energy delivers innovative gas sensing instruments for numerous markets, including global energy, industrial materials, and advanced technologies. Our gas portfolio consists of gas modules and instruments that provide superior sensitivity over other gas detection techniques.
-
Product
Skoad Oxygen Sensor
KS60113 - Skoad
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
CO, Alcohol and VOC Gas Sensor Breakout
MiCS5524
-
Give your next sensor project a nose for gasses with the Adafruit MiCS-5524 Gas Sensor Breakout. This breakout makes it easy to use this nice sensor from SGX Sensortech. The MiCS-5524 is a robust MEMS sensor for indoor carbon monoxide and natural gas leakage detection, it''s suitable also for indoor air quality monitoring; breath checker and early fire detection.
-
Product
Intensified Cameras - Ultra-Sensitive CMOS Cameras from Deep UV to NIR Spectrum
iCameras
-
The cameras are equipped with a high-resolution sensor with high frame rate for excellent quality of image production, which is well‐suited to detect high speed moving objects or ultra-fast phenomenon.The mechanical architecture of the iCamera is small, compact and light-weight, especially designed for easy integration into any system.The iCamera features an exceptional sensitivity based on high QE image intensifier - ultra-fast gating technology down to a few nanoseconds, which allows it to be coupled with a laser source to perform high fidelity active imaging.
-
Product
Electrical Safety Test Solutions
-
Hipot Analyzers with 500VA output rating can be used to test and analyze the withstand voltage of high power and leakage current for the products like motor stators and rotors with high parasitic capacitance. Corona detection can be used for turn-to-turn or turn-to-ground test to avoid winding insulation failure from corona discharge.
-
Product
Thermal Imaging Cameras
-
Thermography tools are indispensable when it comes to non-contact detection of thermal differences. Thermal imagers can be used to find defects in buildings, discover damage during maintenance, or analyze thermal processes.
-
Product
4-Ch Analog Input Module
ADAM-3617
Analog Input Module
Accuracy: ±0.1% or better of FSR (Voltage) ±0.2% or better of FSR (Current)Resolution: 16-bitVoltage/Current: ±10V, ±2.5V, 0 ~ 20mA, Range 4 ~ 20mAIsolation Voltage: 2000 V DCSampling rate: 10 sample/second (total)Burn-out detection: Yes (Current-only)Input Impedance: 0.1 MΩInput Type: Voltage, CurrentChannels: 4, differential
-
Product
Portable Security System
Sensor-1
-
The portable security system that fits in the palm of your hand. Sensor-1 detects real-time changes in motion and alerts you when your important items move. Operates independent of the mobile app. Communicates with smartphones, tablets, laptops and desktops.
-
Product
NI-9266 , 8-Channel C Series Current Output Module
785046-01
Current Output Module
8-Channel C Series Current Output Module - The NI‑9266 is ideal for interfacing and controlling industrial current-driven actuators. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9266 includes channel‑to‑earth ground isolation for safety and noise immunity.
-
Product
Managed Hub
HUB-5595
-
The HUB-5595 is a managed hub designed to operate with the Abaco Systems 5565 family of Reflective Memory real-time network products. The Reflective Memory hub can automatically bypass ports when it detects a loss of signal or the loss of valid synchronization patterns, allowing the other nodes in the network to remain operational.
-
Product
SMART Sensor Gas Detector
IMR EX440
-
IMR Environmental Equipment, Inc.
The detector uses natural diffusion as the method to detect gas. It is constructed with high strength engineering plastics composites with an antiskid rubber housing. The detector is comfortable to hold, is water-proof, and dust-proof.
-
Product
Control Unit
MX 256
-
Teledyne Gas & Flame Detection
The MX 256 is a digital control unit intended for the detection and measurement of gases present in the atmosphere and more generally for the processing of any digital signal from digital sensors (OLCT 10N types), relay module, analog output module, logic input module. Thanks to its new option, an industrial controller module or remote HMI, it is possible to add analog input modules for sensor-transmitter connection (4-20 mA) and / or relay modules, this allows to not only extend the capacities but also to have event recordings (Location, Alarms,.....) and to have access to the data via the embedded web page.
-
Product
Thermal Imaging Camera
TI160 - P5
-
TI 160-P5 is a special thermal imaging camera for human body temperature measurement only. Its has Accurate temperature measurement, real-time imaging, ability to quickly lock the hot-spot. It is been widely used in airports, docks,railway stations, schools, shopping malls and other public places to check human body temperature abnormalities. Palmetto design, compact and lightweight, integrated visible light function. Reliable performance and accurate temperature measurement can effectively improve the efficiency of detection.
-
Product
EVISION Obstacle Detector
MS 1528
-
Obstacle Detector is a distance-measuring system based on ultrasonic sound utilizing the LPC2364FBD100. The system transmits a burst of ultrasonic sound waves towards the subject and then receives the corresponding echo. The LPC2364FBD100 integrated analog comparator is used to detect the arrival of the echo to the system. The time taken for the ultrasonic burst to travel the distance from the system to the subject and back to the system is accurately measured by the LPC2364FBD100. Assuming the speed of sound in air at room temperature to be 1100 ft/s, the LPC2364FBD100 computes the distance between the system and the subject and gives the information to buzzer. The minimum distance that this system can measure is eight inches and is limited by the transmitter’s transducer settling-time. The maximum distance that can be measured is 2 meter. The amplitude of the echo depends on the reflecting material, shape, and size. Sound-absorbing targets such as carpets and reflecting surfaces less than two square feet in area reflect poorly. The maximum measurable range is lower for such subjects. If the amplitude of the echo received by the system is so low that it is not detectable by the Comparator. This system is mainly used to replace normal sticks for the visually impaired (blind) peoples. This unit has standard USB 2.0 for mobile interface and has android application for user interface
-
Product
Diagnostic Testing
-
Response Dynamics Vibration Engineering, Inc.
Response Dynamics has made diagnostic testing our core focus for over 30 years. We do this detective work well because we have particular expertise in structural dynamics and how it relates to vibration and acoustic noise issues on a myriad of levels. We enjoy this work because it stays interesting and draws on multiple disciplines in engineering and science.
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Advanced Series
-
TWA Advanced series is the latest DV Power solution for three-phase transformer winding resistance measurement and tap changer analysis. They are capable of testing six transformer windings with a single cable connection, as well as three-phase automatic transformer demagnetization. It has the option of the automated test mode, where the instrument operates the tap changer without operator input (minimizing the risk of human error) and records winding resistance results based on pre-selected stabilization criteria.The unique DVtest method of tap changer analysis enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, together with the measurement of tap changer motor current which detects motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or simultaneously on three phases. It can also be performed together with the winding resistance test in all tap positions.A unique advantage of TWA Advanced instruments is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer connected in a YN configuration. This can significantly speed up the testing– for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.TWA500 is equipped with a large 10.1” graphical touch-screen display, while TWA400 has a 7” graphical touch-screen display. Besides making the interface much more user-friendly compared to older winding ohmmeters, it also enables certain test options that were previously available only with DV-Win software. The most important among them are DVtest, tap changer motor current measurement, “Heat Run” test, test templates, and automatic test mode.
-
Product
Scientific CMOS Camera
Prime BSI Express
-
The Prime BSI Express Scientific CMOS (sCMOS) is designed on a compact platform optimized for integration and delivers the perfect balance between high resolution imaging and sensitivity with an optimized pixel design, USB 3.2 Gen 2 connectivity and near perfect 95% Quantum Efficiency to maximize signal detection.
-
Product
Field Strength Analyzer
SRM-3006
-
Selective measurement of high frequency electromagnetic fields. Complete, easy to use test system, consisting of a base unit and measuring antennas, for non-directional detection of fields and their sources in the frequency range from 9 kHz to 6 GHz and from 24.25 GHz up to 29.50 GHz with 5G FR2 Antenna.
-
Product
Light Sensor
NaPiCa
-
Panasonic Industrial Devices Sales Company of America
Visible light sensor (Silicon Photo IC) that detects light and converts into electrical current. Consists of a photodiode and built-in amplifier. Optical filter provides spectral response similar to human eye sensitivity. Applications include: LCD Backlight Control, Commercial and Residential Lighting Brightness Control, Security Lighting.
-
Product
Handheld Digital Multimeter, AC/DC Current, AC/DC Voltage, Capacitance, Resistance, True RMS
72-2995
-
40,000 count industrial True RMS digital multimeter is a highly versatile handheld instrument boasts 5-1/2 digit TRMS accuracy. It provides AC/DC voltage and current measurement, resistance, capacitance, temperature and frequency measurement, displaying readings on a backlit LCD digit and analogue bargraph display. Other features include non-contact voltage detection, continuity and diode test and USB data logging. All this is housed in a rugged overmolded enclosure with carry case, test leads and USB interface cable included.
-
Product
Nano-focus X-ray Inspection System
X-eye NF120
-
Nano-focus Tube of 400 nano resolution is installed which is specialized for Semiconductor Packaging, Wafer Level Packaging(WLP) requiring detection of Sub-micron defects.Able to trace and inspect defected area precisely by precise movement of axis with Anti-vibration table.Tomography is available if 3D CT module is added and Wafer Bump Automatic Inspection is available from loading to inspection with wafer handler systems.
-
Product
Microwave Monitor w/ Vinyl
A100p
-
This single-range, RF power measurement instrument is designed to operate in the 2.45 GHz range. Used by field service engineers, engaged in the repair and maintenance of commercial and domestic microwave heating equipment, its primary function is the detection RF microwave energy leakage.
-
Product
Online PD Spot Tester
Liona
-
Cable testing and diagnostics with the BAUR liona. Liona is a portable online PD spot tester for measuring and locating partial discharges in cables and switchgear during normal mains operation. Liona lets you test cable systems and electrical equipment online without switching off partial discharge activities, and then generate trend analyses. Even a PD spot test (duration: 5-10 minutes) is capable of reliably assessing the current status of your system.* Automatic PD detection during normal mains operation (without switching off the cable route)* With DeCIFer technology: PD identification based on 500 million measurement results* Precise online PD mapping with PD transponder
