-
product
USB Controlled Multi-Function DAQ For ATE Education And ATEasy Training
GT98901 Series
The GT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all of which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol. Power for the board is provided via the USB interface, providing a totally self-contained assembly which can provide users wit...show more -
product
Serial to Relay Minibox™
Model 2364
* Model 2364-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Optional 1 'U' high Rack Mounting Kits hold one or two 2364s.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 2364s.* Optional 115750 Terminal Board and Terminal Strip for easy connections without soldering. See the Serial Accessory page.
-
product
RF Signal Generator With 1.5 And 3GHz Models
TGR205x Series
150kHz to 3GHz (TGR2053) and 150kHz to 1.5GHz (TGR2051) frequency rangeHigh signal purity, phase noise <-117dBc/Hz (typical) at 1GHz output and 10kHz offsetAmplitude range of -127dBm to +13dBm0.1dBm amplitude setting resolutionInternal or external analogue modulations (AM, FM, PM)Amplitude can be set in dBm, dBμV or in linear Volts.Internal or external digital modulations - ASK, OOK, FSK, 3FSK, 4FSK, GFSK, MSK, GMSK, HMSK & PSK with U01 optionModulation SynchronisationFast amplitude and/o...show more -
product
Serial-to-Daq Card
Model 2307
* 2307 Board provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Board. * DE-9 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * Runs on 5 Vdc power.
-
product
GPIB Serial Interface
Model 4804B
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
product
6 PCS Deluxe Light Set
3606
Peaceful Thriving Enterprise Co Ltd
Kit packed in a deluxe blow mold case.Quick, efficient and economic way to find faults find on the following electronic fuel (EFI) system:1. 3405-BOSCH PFI2. 3410-GM TBI3. 3411-FORD TBI4. 3412-GM PFI5. 3413-GEO TBI6. 3414-GM SCPI.
-
product
Aerospace and Aviation Solutions
SCOEs and EGSEs by LXinstruments are used during test and validation of satellite assemblies and modules in aerospace applications. As an example, we implemented solar array simulators, battery simulators and high-power load racks for a German satellite manufacturer for testing satellite power supply systems. Due to the high power ratings, the systems are partially equipped with water cooling. Specialized switching modules were developed for switching DC currents at high voltage levels; these ca...show more -
product
FaithTech FTLP Series 100W/180W Portable Programmable DC Power Supply
FaithTech FTLP Series
Shenzhen FaithTech Technology Co., Ltd.
FTLP series is a kind of programmable Portable bench DC power supply, with the widest output range, which allows engineers to test more program requirements with just one device. To be exact, the FTLP series provides full power all the way down to 25% of the rated output voltage. The FTLP series is equipped with RS232 and RS485 as standard interfaces that are essential for system integration, you can also choose USB or LAN interface as your add-on interfa...show more -
product
Noid Lights, IAC Test Lights & Ignition Spark Tester Kit
36330
Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes 8 Noid Lights (for checking GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, BOSCH 2 and GM Multec 2; 2 IAC Test Lights (for straight and 90 applications); and Cat. No. 23900, In-line Ignition Spark Checker.
-
product
Serial-to-Daq Minibox
Model 2367
* 2367 provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Module. * DB-25 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * The 2367 is packaged in a CE approved Minibox™ metal case to minimize EMI/RFI. * 1 U high Rack Mounting Kit mountsone or two 4867s.* Plug-on Terminal Board simplifies wiring connections.* Includes Universal Power Adapter and 62-pin mating connector.
-
product
Optical Head Interface
N7749C
The N7749C optical head interface can control two or four 8162-C series optical power meter heads. Readout is supported over LAN and USB interfaces with a built-in web-browser GUI and the SCPI command set common to Keysight optical power meters.
-
product
Smart GPIB Serial Interface Board
Model 4816
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
product
Polarization Controller and Scrambler - MATRIQ
The Pol 1000 Series enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands.
-
product
Tunable CW Laser Source
IQTLS
The IQTLS is a continuous wave (CW) laser source combining high-power output, narrow 100kHz linewidth and 0.01pm resolution tunability. Available in single or dual laser configurations, this tunable laser source can be controlled locally via USB or Ethernet ports and is SCPI VXI-11 compliant.
-
product
GPIB to Relay Interface Boards
Model 4864 OEM
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.*...show more -
product
Programmable DC Power Supply
IT6100 Series
IT6100 series assure you accurate measurements with 0.1mV/0.1mA high resolution and high accuracy. With high-speed List mode output and voltage rise speed up to 20ms, it can independently edit and perform the default voltage waveform to meet the high-speed test needs. IT6100 series has built-in 5 1/2 digital voltmeter and milliohm meter, which can measure additional signals. IT6100 series supports SCPI communication protocol, GPIB/USB/RS232 interfaces are optional for customers.
-
product
Polarization Controller and Scrambler - PXIe
Pol 1000 Series
The Pol 1000 Series PXIe module enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands. Pol 1000 Series can be used with our wide range of optical and electrical PXIe test modules, and can be used to build complete mixed-signal test platforms.
-
product
Wide-range Programmable DC Power Supply
IT6900A Series
IT6900A series wide range programmable power supply have built-in standard RS232, USB, GPIB, RS485 and analog interface (RS485 and analog interface are just for IT6900B), support SCPI protocol, facilitate remote control, industrial PLC control and the formation of intelligent test platform. Remote compensation terminals avoid the problem of inaccurate testing caused by voltage drop on the wire.Low ripple, low noise and built-in digital voltmeter make IT6900A easy to do external measurement.IT6900A can be widely applied in DC-DC power supply module, battery charging and sensors and other test areas.
-
product
DC Power Supply, 6V, 5A, 30W
E36100 Series
Keysight E36100 Series basic DC power supplies feature a compact size (2U, -rack), a high-contrast OLED display that is viewable from any angle, and modern USB and LAN (LXI Core) connectivity. They also include low power current measurement capability and overvoltage, overcurrent, and overtemperature protection. You can control these power supplies via the intuitive front-panel interface, a Web interface running on a browser, a SCPI or IVI program, Keysight IO Libraries, or a BenchVue app running on your PC or mobile device.
-
product
ATE System Power Supplies
For more than 50 years, Keysight's automated test equipment (ATE) power supplies have changed the way engineers prove their designs, understand issues, and ensure product quality. Our programmable ATE system power supplies' compact design makes it easy to integrate them into any system. Keysight power supplies make it easy to update a test program with modern interfaces, LXI-core capability, and SCPI language. Accelerate test time with fast command processing and quick settling times.
-
product
Smart GPIB Serial Interface Board
Model 4806
* Provides GPIB-to-serial and serial-to-serial data paths for serial devices with RS-232 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message. • On board voltage regulator for operation from 5 to 15 Vdc power. • Rear panel mounting eliminates cables.
-
product
GPIB to Quad Serial Interface
Model 4896
* Provides four RS-232/RS-422/RS-485 Serial Channels.* High speed, 115.2 K baud channels include 60 K byte buffers.* > 600 K byte/sec. GPIB data transfer rate.* SCPI commands set serial configuration and GPIB address.* LCD display shows Bus activity, buffer status, serial interface signals and channel settings.* 1 U high rack mount kit mounts one or two 4896s * Includes US 115 VAC Power Adapter, Manual and Support CD.
-
product
Noise Figure Meters
H5M Series
*Frequency range from 10 MHz to 4/20 GHz*Noise Ratio and Gain measurements*Frequency converter measurements with a fixed or external heterodines*Built-in thermostatic YIG preselector*High measurement speed*Extend the NFA solution up to 50 GHz with special downconverter unit*SCPI Language Compatibility
-
product
Serial Controlled Relays And Relay Drivers
*ICS's Serial controlled Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the Serial to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are IEEE-488.2 compliant and use SCPI commands for operation with NI or Agilent VISA, LabVIEW and VEE or any Serial programming language. Use ICS's interactive Serial Keyboard program for easy operation from your PC without having to write a program.
-
product
GPIB to Relay Minibox™
Model 4864
* Model 4864-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Optional 1 'U' high Rack Mounting Kits hold one or two 4864s.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 4864s.* Optional terminal board and terminal strip for easy...show more -
product
USB Controlled Multi-Function DAQ for ATE
GT98901
The GXT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol.
-
product
Modbus Register Converter
Model 2390
* Converts Modbus Registers and variables for replacement Modbus devices.* Maintain existing software when upgrading Modbus systems.* Provides serial control of Modbus RTU devices from any ASCII source.* User defined Register Conversion Table supports all Modbus RTU devices.* Internal Register Conversion Tables for Watlow F4-to-EZ-ZONE and F4-to-F4T conversion.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes baud rate conversion capability.* Uses SCPI commands to load th...show more -
product
ANSI X3.28 to Modbus RTU Converter
Model 2399
* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as...show more -
product
Basic Spectrum Analyzer
N9322C
Quickly uncover key insights through fast, value-priced, general-purpose performance up to 7 GHz with -152 dBm DANL and 0.6 dB overall amplitude accuracy Streamlined for straightforward and efficient operation with marker demodulation, one-button optimization, and user-definable soft keys Robust measurement features for easily characterizing your product Automation and communication interface with industry standard SCPI language support and USB and LAN connectivity choices
-
product
(9 PCS) 8 Noid Light Kit With Fiber Optic Noid Light Extension
3621A
Peaceful Thriving Enterprise Co Ltd
*Kit packs in a deluxe molded plastic case.*Set includes: 8 Noid lights for testing GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, GM MULTEC 2 and BOSCH 2.*Plus one fiber optic Noid Light extension.
