Incremental Encoders
Measure movement by producing quadrature output codes corresponding to the amount of motion.
See Also: Encoders, Encoder Test, Absolute Encoders, Linear Encoders
- TEAM SOLUTIONS, INC.
product
Motion Control Board, PCI
APCI-8001-1
*Axis control for 1 servo or stepper motor*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders *or SSI absolute encoders
-
product
Incremental Encoder
ED1
Chuan Sheng Electronics Co., Ltd.
● Easy installation, high-speed pulse generator, high-speed rotation control, and more.● Ф 38 diameter with high resolution up to 1024P/R● Push-pull output can use for NPN or PNP input meter
-
product
6 Channel Encoder Input Controller
CPCI323
The CPCI323 Quadrature Incremental Encoder Interface is designed to interface with up to six quadrature incremental encoders. This is an ideal solution for all applications where several encoders must be connected with a maximum of flexibility and a minimum of overhead.
-
product
Speed Switch
UDS1000
Features • Works with remote / external quadrature pulse frequency output sensor / incremental encoder (NPN or PNP) • DPDT relay changes state when shaft direction reverses • Reverse-over-speed setpoint adjustment from 0.5-5,000 rpm • Relay resets when reverse motion stops • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • Explosion proof/NEMA 4X housing • UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
product
P104 LVDT/RVDT Measurement Board
73LD4
NAI’s 73LD4 is a PC104-compliant LVDT/RVDT Measurement Board with six separate transformer-isolated channels. The channels can incorporate up to six programmable LVDT/RVDT-to-Digital Tracking Converters in a stack-through module. Each channel is programmable for 2-, 3-, or 4-wire inputs that automatically range between 2.0 volts and 28 volts, so there is no need to purchase multiple boards set for specific inputs. Operating frequency between 360 Hz and 10 kHz can be specified. Each channel also produces differential incremental encoder (A & B) outputs with programmable resolution and a zero-degree marker pulse.
-
product
Quadrature Incremental Decoder Interface for VMEbus
VME323
The VME323 is an Intelligent Quadrature Incremental Decoder VMEbus Board which can be configured for interfacing quadrature incremental encoders with or without an index channel. In index mode up to sixteen encoders with two quadrature channels and an index channel can be connected, and in non-index mode up to twentyfour encoders with two quadrature channels can be connected. The VME323 operates on two encoder input channels and decodes a pair of out-of phase signals in order to increment or decrement a counter.
-
product
Motion Control Board, PCI
APCI-8001
*Axis control for 3 servo or stepper motors*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders or SSI absolute encoders*Possibility of extension to a total of 8 axes*Menu-driven test application
-
-
product
Rotary Encoders
Incremental encoders
You will always find the suitable incremental encoder here: from the cost-efficient standard versions to the high-resolution design with 320,000 pulses per revolution - in various designs and with robust magnetic or precise optical scanning. Optionally with HTL, TTL, or sine signals and all common mechanical interfaces.
-
product
Encoders
At Variohm we have a range of encoders we can offer. Our range includes Absolute Encoders and Incremental Encoders as well as Lift Measuring Systems.
-
product
16 Channel USB Sensor Interface
RogaDAQ16
With the introduction of the RogaDAQ16 USB 2.0 data acquisition system, a new age of measurement technology begins.*USB 2.0 / 480MBIT (USB1.1/12MBIT COMPATIBLE)*16 analog input channels (16bit/500kHz max.)*ICP ® ( IEPE ) sensor supply (24V/4mA)*0.125V to 10V input range*Individual preamplifiers*4 analog output channels (16bit/100kHz)*Powerful DSP (255MIPS) for filtering, control etc.*24 digital I/Os*Optional 24bit counter, timer, PWM, incremental encoder*Free drivers for major application software*including DASYLab; LabView & DiaDem drivers & RogaRec Software
-
product
P104 Synchro/Resolver Measurement Board
73SD4
NAI’s 73SD4 is a DSP-based, PC104-compliant Synchro/Resolver Measurement Board with six separate, isolated channels. These channels can incorporate up to six Synchro/Resolver-to-Digital Tracking Converters in a stack-through module. Each channel also produces differential incremental encoder (A & B) outputs (with programmable resolution) and a zero-degree marker pulse. Commutation outputs are available for 4-, 6-, or 8-pole brushless DC motors that eliminate the need for Hall Effect sensors, thereby reducing both processor time and bus traffic.
-
-
product
C Series Counter Input Module
The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, an...show more -
product
Encoders
Effective feedback devices for positioning applications with different technologies in the incremental encoder's format such as reflective optical technology, transmissive optical technology with and without differential line drives and multitude of line counts in compact low profile sizes. These incremental encoders are offered in both modular and bearing construction.
-
-
product
High-Precision XY Stage
V-731
Physik Instrumente GmbH & Co. KG
Reference-class XY stage. Travel range 205 mm × 205 mm (8"). Unidirectional repeatability to 0.1 μm. Velocity to 200 mm/s. Incremental encoder with 10 nm resolution.Optionally with stepper motor.
-
product
Incremental Encoder Simulator
ENC-SIM01
Plant Control and Automation Pty Ltd
This instrument is designed to simulate the function of most types of incremental encoders; it allows the engineer to fully test a control system that uses a rotary or linear shaft encoder, without the need for any mechanical movement.
-
-
product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-02
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
product
Closed-Loop Motor Controller
MS320
Master and Ratio-Follower modes and programmable input functions. Options include analog speed feedback input, analog setpoint inputs and relay outputs. Works with incremental shaft encoders and pulsefrequency output shaft speed sensors. Optional explosion proof enclosure or NEMA 4X enclosure kit.
-
product
Incremental > Standard Encoders - Hollow Shaft
Incremental > Standard Encoders - Hollow Shaft
-
product
Synchro to Digital-Resolver to Digital Converters
Synchro- Burst
Computer Conversions Corporation
Computer Conversions Corporation's Synchro-Burst is a complete 2 channel Synchro to encoder interface designed to easily integrate inherently absolute rotary synchro, resolver or linear LVDT position sensors into motion controls and counters that are normally only designed to facilitate incremental encoder feedback.
-
product
Absolute Encoders
US Digital designs and manufactures absolute encoders in both optical configurations, for the highest possible resolution and accuracy, and magnetic versions for demanding environments. In either case, absolute encoders report a shaft angle within a single 360-degree shaft rotation without stops or gaps. Unlike incremental (sometimes called "relative") encoders, absolute encoders provide true (absolute) shaft position, eliminating the need for a "home" or "zero" cycle after a supply-voltage power cycle.
-
product
Explosion-Proof Transducer
HX
Computer Conversions Corporation
Computer Conversions Explosion-Proof Transducer Housings are designed to operate in hazardous environments requiring an Explosion-Proof Enclosure. Suited with internal (Factory Installed) resolver-transducers; these units can be provided as part of an absolute and/or incremental encoder system. Most transducer cables only require six conductors, shielding is optional, and systems are capable of maintaining 1000' cable runs in severe RFI environments.
-
product
Rotary Encoders
The family of dia 50mm incremental rotary encoders features an improved water resistance compared to standard models.
-
product
6 Channel Encoder Input Controller
PCI323
The PCI323 Quadrature Incremental Encoder Interface is designed to interface with up to six quadrature incremental encoders. This is an ideal solution for all applications where several encoders must be connected with a maximum of flexibility and a minimum of overhead.
-
product
Optical Rotary Encoders
Optical sensing technology is the most precise and offers the highest resolution of the position sensing technologies. Rugged construction and years of field proven service makes BEI optical rotary encoders ideal for operating in harsh industrial environments including oil well drilling, machine control, agricultural machinery, web process control, robotics, elevators, construction equipment, cranes, motor feedback and any closed loop control systems. BEI optical encoders are available as increm...show more -
product
Incremental > Heavy Duty Encoders - Hollow Shaft
Incremental > Heavy Duty Encoders - Hollow Shaft
-
product
Signal Converters For High-accuracy Angular Measurement
EIB 1500 series
*Interpolation and digitizing electronics for the real-time digital processing of positions from two scanning heads*Input: incremental rotatory HEIDENHAIN encoder with two scanning heads and distance-coded reference marks (relative orientation of scanning heads: 180° ± 5°)*Output: EnDat 2.2, Fanuc Serial Interface, Mitsubishi high speed serial interface*Integrated subdivision: 16 384-fold
-
product
Displacement and Encoders
INCREMENTAL digital Transducers are mainly designed for displacement measurement in machine tools and other industrial applications. The sensors are characterized by high precision and are absolutely dust and waterproof. The used materials permit applications in heavy industrial environments.DISPLACEMENT Transducers are suitable for measurements of small distances up to 50mm. They are characterized by high accuracy and repeatability, reliability and fast response. Digital ENCODERS operate on optical or magnetical principal and are offered with incremental or absolute coded outputs. They are suitable for precision industrial applications.
