-
Product
2-Ch 1 GHz A/D and D/A with Virtex-6 FPGA - 6U VPX
Model 58630
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 1 GHz 12-bit A/D- Two 1 GHz 16-bit D/A- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG-HS
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
Digital Demultiplexers
-
Advanced Science and Novel Technology, Co., Inc.
24:48 digital demultiplexer (DMUX) with SSTL1.5 input and output interfaces.Supports data rates from 1.0Mbps to 2.0Gbps.User-controllable independent internal delays for data and clock signals.1.5V I2C control interface with a user-defined 3-bit chip address.Preset function for synchronization of multiple parallel devices.Full-rate output copy of external high-speed clock input signal.Two pairs of clock divided-by-2 and synchronous clock enable outputs for supporting the tree-type demultiplexation structure.Additional synchronous clock divided-by-4 output.Dual power supply of +3.0V and +1.5V.Industrial temperature range.Low power consumption of 2.1W at 2.0Gbps.Available in custom 256-pin BGA package (13mm x 13mm x 2.5mm).
-
Product
PCI Express 2-Port
7203e
-
The 7203e PCI Express serial interface provides two optically isolated serial ports, each individually configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C952 UART with 128-byte Tx/Rx FIFOs that enables data rates to 460.8K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
PXI-6723, 13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module
778998-01
Analog Output Module
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
Up & Down Converter/RF Suite
DNA
-
DNA is one of the most effective phase noise and frequency stability analysers on the market. It is based on a unique digital architecture that reduces thermal noise and obtains top performance in terms of near phase noise, with a limit set by a user reference clock. DNA also includes in-built oscillators for advanced autonomous operation.
-
Product
4-Channel 200 MHz A/D with DDC, Kintex UltraScale FPGA - 3U VPX
Model 52861
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI-6683, TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module
782110-01
Synchronization Module
TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module—The PXI‑6683 timing and synchronization modules synchronize PXI and PXI Express systems using GPS, IEEE 1588, and IRIG‑B to perform synchronous events. The PXI‑6683 can generate events and clock signals at specified synchronized future times and timestamp input events with the synchronized system time. The PXI‑6683 features an onboard temperature-compensated crystal oscillator (TCXO) that can be disciplined to GPS, IEEE 1588, and IRIG‑B for long-term stability. You also can use the PXI‑6683 to route clock signals and triggers with low skew within a PXI chassis or between multiple chassis, providing you a method for synchronizing multiple devices in a PXI system.
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
Low Profile PCI Express 4-Port
7406e
-
The 7406e low profile PCI Express serial interface provides four RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
Clock Generator
CG-1000
-
High-precision OCXO is used for the internal clock.Master clock generator with advanced features such as jitter management and glitchless relock.
-
Product
10-CH General Purpose Timer/Counter & 8-CH DIO Module
cPCI-8554
Counter/Timer Module
- PICMG 2.0 Rev 3.0- Four 82C54 programmable timer/counter chips- Up to 12-CH 16-bit timer/counter- 1-CH 32-bit cascaded timer based on 8 MHz clock source- Four programmable clock sources for each timer/counter- Programmable de-bounce filters for external clock & external interrupt inputs- 8-CH TTL digital inputs & 8-CH TTL digital outputs- +12 V and +5 V power available on the connector
-
Product
Timing And Sync
-
Precision timing is critical for defense and commercial industries and powering essential network operations. Safran offers secure time servers and solutions for accurate network synchronization, ensuring security, compliance, and adherence to best practices. Safran excels in delivering precision timing solutions, including NTPNTP, or Network Time Protocol, is a widely used networking protocol that enables computers and devices to synchronize their system clocks with a reference time source. It ensures accurate timekeeping in computer networks by allowing devices to obtain precise time information from NTP servers, which are typically synchronized to highly accurate atomic clocks. NTP is essential for various applications and services that rely on synchronized time, such as network security, authentication, and data logging. time server appliances and GPSGlobal Positioning System is a navigation satellite system. See also master clocks globally.
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - PCIe
Model 78620
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user-configurable gigabit serial interface- LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
8-Channel 200 MHz A/D with DDC, Virtex-6 FPGA - 6U VPX
Model 58661
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 200 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- Two multiboard programmable beamformers- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Phoenix LVDS Frame Grabber (PE1)
AS-PHX-D36-PE1
-
Phoenix-D36 is a PCI Express board for the acquisition of digital data from a variety of sources, including digital frame capture and line scan cameras. It has 36 bits used for input data, with 4-bits for control. This provides support for a single 12 bit RGB or 32 bit mono data source, including multi-tap cameras. The 4-bit control inputs are dedicated as Frame Enable, Line Enable, Data Enable and Pixel Clock.
-
Product
Secondary Master Oscillator
VCH-002
-
The secondary master oscillator (VZG) is designed to operate in a digital communication network as a synchronization equipment of the second level of the hierarchy. Its task is to track in phase one or more clock signals coming through the network from the synchronization equipment of the highest or equivalent level of the hierarchy.
-
Product
FMC Dual ADC 12-bit 2.6 GSPS, Single DAC 16-bit 12 GSPS
FMC250
-
The FMC250 is an FPGA Mezzanine Card (FMC+) per VITA 57.4 specification. The board has dual ADC and single DAC. The FMC250 utilizes dual AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a single DAC (AD9162 or AD9164) providing 16-bit conversion rates of up to 12 GSPS. The analog input, digital output, clock and trigger interfaces of the FMC250 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
Product
GPS Synchronization
PGPS04i
-
The PGPS04i is a multiple-functional time synchronization device that integrates with GPS time synchronization, IRIG-B outputs (DC-TTL/DC-RS422/optical), IRIG-B pulse input (DC-TTL/DC-RS422/fiber), 1PPS/1PPM pulse output DC- TTL/DC-RS232/fiber), timing set of whole trigger points, real-time clock auto-generating and other relevant functions.
-
Product
Rubidium Oscillator
-
Rubidium oscillators are a type of atomic clock and are the most accurate time standards known and are used as time distribution services to control things such as telecommunications infrastructure, TV broadcasts and global navigation satellite systems (GPS).
-
Product
Power System Recorder
TESLA LITE
-
ERLPhase Power Technologies Ltd
The new TESLA LITE is an economical user-friendly multi-timeframe power system recorder: Economical yet complete power system recording for custom applications in smaller substations. Easy to use intuitive software Simultaneous transient fault, dynamic swing and trend recording and event logging Fault location derived from single and calculated currents IRIG-B clock synchronization (modulated and unmodulated) Smallest footprint among recorders allows easy retrofit and installation 12 current, 6 voltage and 38 digital inputs
-
Product
LVDS Digital I/O with Virtex-6 FPGA - 3U VPX
Model 52610
-
- 32 bits of LVDS digital I/O- One LVDS clock- One LVDS data valid- One LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAs- DMA controller moves data to and from system memory- Up to 2 GB of DDR3 SDRAM- PCI Express Interface- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
Spectrometer
XFFTS
-
This spectrometer is a control chassis which accomodate 8 FFTS cards, each with up to 2.5 GHz bandwidth. Each XFFTS-board operates from a single 5 Volt source and dissipates less than 30 Watt, depending on the actual configuration in terms of bandwidth and number of spectral channels. Precise time stamping of the processed spectra is realized by an on-board GPS/IRIG-B time decoder. Furthermore, the 10-layer boards include a programmable ADC clock synthesizer for a wide range of configurations (bandwidth: 0.1 – 2.5 GHz), making the spectrometer flexible for different observation requirements .
-
Product
Frequency Doubling Comb Generator
COMBGEN6DIFF
-
*Differential output - can also provide two separate single ended complementary outputs.*Pulse height of up to +4V peak into 50 ohms, on positive output*Pulse height of up to -4V peak into 50 ohms, on negative output*Rise time < 80pS, FWHM of approximately 120pS*Produces pulse on both edges of input clock, thereby doubling frequency.*Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz.*Usable energy to >10GHz.*Can drive any load, including short, without damage.*Power Requirements: -12V @ 120mA and +24V @ 80mA
-
Product
OnyxFX FlexorSet 8-Channel 250 MHz A/D - PCIe
Model 7070-316
-
- Supports Xilinx Virtex-7 VXT FPGA- GateXpress supports dynamic FPGA reconfiguration across PCIe- Eight 250 MHz 16-bit A/Ds- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Also available as Model 5973-316
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - XMC
Model 71821
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Exceptional dynamic range and analog signal integrity- Xilinx® Kintex® UltraScale" FPGA- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of 2400 MHz DDR4 SDRAM- Programmable frequency synthesized sample clock generator- Sample clock synchronization to an external system reference- Powerful DMA controllers for moving data- PCI Express (Gen. 1, 2 & 3) interface up to x8- Multi-channel synchronization with clock/sync bus- Optional clock/sync generator for multi-board systems- Optional LVDS port for custom FPGA I/O- Optional gigabit serial links for custom FPGA I/O- Ruggedized and conduction-cooled versions available- Navigator® BSP for software development- Navigator® FDK for custom IP development- SPARK® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 57651
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- One multiboard programmable beamformers- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
3-Ch 200 MHz A/D w/ DDC & 2-Ch 800 MHz D/A w/ DUC, Virtex-6 FPGA - 3U VPX
Model 52621
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Optional LVPECL clock/sync bus for multiboard synchronization- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Standard High Speed D/A Converters
-
Analog Devices digital-to-analog converter (DAC) portfolio provides solutions for your high speed and precision DAC applications. Thanks to complete data sheets and evaluation boards, as well as broad support among our clock and timing, RF, power management, and op amp portfolios, our DACs can help you reduce time to market and system design costs. A high speed range from 30 MSPS to multi-GSPS, 8- to 16-bit resolution, and a tiny package are just some of the features that make our industry-leading d/a converters stand out.
-
Product
PXIe-1095, 18-Slot (5 Hybrid Slots, 11 PXI Express Slots, 1 PXI Express System Timing Slot), Up to 24 GB/s PXI Chassis
785971-01
Chassis
PXIe, 18-Slot (5 Hybrid Slots, 11 PXI Express Slots, 1 PXI Express System Timing Slot), Up to 24 GB/s PXI Chassis - The PXIe-1095 features a high-bandwidth backplane and up to 82 W of power and cooling in every slot to meet a wide range of high-performance test and measurement application needs. The chassis incorporates two hot-swappable power supplies to improve the mean time to repair (MTTR) of the PXI system; it also offers a Timing and Synchronization option that includes a built-in oven-controlled crystal oscillator (OCXO) for increased clock accuracy and external clock and trigger routing. It accepts PXI Express modules in every slot and supports standard PXI hybrid-compatible modules in up to five slots.
