Digital Visual Interface
See Also: DVI
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 12 Channels, 12 Single-Ended Inputs
DN6.447-12
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Network Interface Card
PMC-GBIT-DT2BP
Interface Card
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
Product
PCIe 14 Bit High Speed Digitizer - 400 MS/s on 4 Channels
M4I.4481-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXIe-8430, 16-Port, RS232 PXI Serial Interface Module
781472-02
Serial Interface
16-Port, RS232 PXI Serial Interface Module—The PXIe‑8430/16 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
sbRIO-9866, Non-Enclosed, 1-Port C Series LIN Interface Module
785965-01
LIN Interface
Non-Enclosed, 1-Port C Series LIN Interface Module—The sbRIO‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The sbRIO‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis. Non-enclosed modules are designed for OEM applications.
-
Product
Multichannel Memory-Mapped ARINC 708/453 Interface Card
EXC-708mPCIe
Interface Card
The EXC-708mPCIe is a multichannel, memory-mapped ARINC 708/453 interface card that supports two ARINC 708/453 channels, each programmable as transmit or receive. Each channel implements a 64K x 16 FIFO and supports polling and/or interrupt driven operation. The card complies with the PCI ExpressTM Mini Card standard. It’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating 708 interfaces and for performing system simulation of the ARINC 708/453 Weather Radar Display databuses, both in the lab and in the field. In Transmit mode, each ARINC 708 word is written to the FIFO as a block of 100 16-bit words. In Receive mode, each ARINC 708 word is stored in the FIFO as a block of 103 16-bit words. The first two words comprise the 32-bit Time Tag, indicating the word’s time stamp. The next 100 words comprise the 1600 bits of the ARINC 708 word, which are followed by the Status Word.The EXC-708mPCIe card comes complete with C drivers including source code.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.448-02
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 24 Channels, 80 MS/s on 48 Channels, 48 Single-Ended Inputs, 24 True Differential Inputs
DN6.596-48
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
PCI-8433, 4-Port, PCI, Isolated, RS485/RS422 Serial Interface Device
779146-01
Serial Interface
The PCI‑8433/4 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
8-Ports Gigabit Ethernet RCV Interface (R)
YAV90058
Ethernet Interface
8x RJ45 LAN connectors to VPC RCV 192 pins module.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
CAN Interface
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
PCIe 12-Bit, 6 GS/s, Gen3 Digitizer
EON Express CompuScope
Digitizer
The GaGe EON Express CompuScope PCIe Gen3 digitizer board features unprecedented speed and resolution in a 6 GS/s streaming digitizer with 1.75 GHz bandwidth and PCIe data streaming rates up to 6 GB/s.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
DN2.221-02
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-104
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5916-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
sbRIO-9476 , Non-Enclosed, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module
783951-01
Digital Module
Non-Enclosed, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module - The sbRIO‑9476 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 36 V, based on the external power supply, and features transient overvoltage protection between the output channels and the backplane. You can programmatically monitor the built-in overcurrent and short-circuit protection status of each channel. Non-enclosed modules are designed for OEM applications.
-
Product
PXIe-5763 , 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785160-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-01
CAN Interface
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
NI-9435, ±5 VDC to ±250 VDC/10 VAC to 250 VAC, 4-Channel (Sinking/Sourcing Input), 3 ms C Series Digital Module
779010-01
Digital Module
±5 VDC to ±250 VDC/10 VAC to 250 VAC, 4-Channel (Sinking/Sourcing Input), 3 ms C Series Digital Module - The NI‑9435 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel accepts signals from ±5 VDC to ±250 VDC and 10 VAC to 250 VAC; features transient overvoltage protection between the input channels and earth ground; and has an LED that indicates the status. The NI‑9435 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
Handheld Digital Multimeter, 4.5-digit, with Organic LED Display (OLED)
U1253B
Digital Multimeter
The Keysight U1253B 4.5-digit handheld digital multimeter (DMM) is feature-packed to simplify the troubleshooting of electronics and electrical circuits indoors, on the bench or in the field. Key capabilities include its organic LED (OLED) display that provides razor-sharp readings even in dark, off-angle situations. The U1253B is the world's first OLED handheld DMM of its kind. For those long, continuous measurements, the DMM equips you with the easy-to-use GUI data-logging software to automate virtually unlimited data recordings to PC. The U1253B comes with an integrated 20 MHz frequency counter for high frequency measurements, and a built-in programmable square-wave generator with selectable frequency and duty cycle. With the versatile U1253B, you are well equipped to perform thorough troubleshooting of any faulty circuit.A multi-award winner
-
Product
PXI Digital I/O Module With Power Distribution - With DC-DC Converter
40-228-001
Digital I/O
The 40-228 provides 32 channels of digital input and 32channels of digital output, together with switched +12V,+5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5Vsupply output. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter(40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
Product
Smart Aircraft Interface Devices
webCS
Interface
The Ballard webCS® is the first highly integrated smart AID/server/router that securely bridges avionics data with wired and wireless networks in a single compact box. This wireless aircraft communications server platform is simple to install and configure, safe to interface with aircraft domains, and provides highly secure data transfer. The compact, versatile webCS enables aircraft operators to easily gather and process aircraft data, and then route it to where it is needed—whether on or off the aircraft.
-
Product
PXI Digital Multimeter
Digital Multimeter
PXI Digital Multimeters, or DMMs, feature AC/DC voltage, AC/DC current, 2- or 4-wire resistance, and frequency/period measurements, as well as diode tests. You can also choose a PXI DMM with an isolated, high-voltage digitizer that can acquire waveforms at sample rates up to 1.8 MS/s at full input range, up to 3 A or 1,000 V. Additionally, you can choose a PXI DMM that can perform basic inductance and capacitance measurements.
-
Product
Nano-Volt/Micro-Ohm Meter, 7.5 Digit
34420A
Digital Multimeter
The Keysight 34420A nanoVolt, micro-Ohm meter is a high-sensitivity multimeter optimized for performing low-level measurements. It combines low-noise voltage measurements with resistance and temperature functions, setting a new standard in low-level flexibility and performance.
-
Product
PXI 32 Channel Switch Simulation Module
40-480-221
Digital I/O
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
10-Ch Pneumatics CAN without RCV module
YAV90PNF
CAN Interface
This pneumatic subsystem is the same as YAV90PNE, but without the VPC receiver module integrated, making it a good option to be used inside the fixture. Since the control is CAN, user can easily place electrovalves inside the fixture without the need to use a bunch of wires.
-
Product
3U CompactPCI Serial 4-Port USB 3.2/2-Port Ethernet Card
cPCI-A3USB
Ethernet Interface
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 4x USB3.2 Gen 1 ports and 2x RJ45 2.5G LAN ports in front panel- 1x USB2.0 port on board- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
Digital I/O Device
Digital I/O
The Digital I/O Device supports channel, current, and voltage options to help you automate applications. This module features programmable input filters to remove chatter, noise, glitches, and spikes on inputs, and these filters also provide debouncing for digital switches and relays. You can use the module to perform safe operation when connected to pumps, motors, and other industrial actuators or machinery using the included power-up states. The module also provides a fail-safe mechanism that monitors for computer or application crashes and place the system in a state to ensure safe recovery. Additionally, some models include high-voltage, high-current, and isolation options to ensure the product can work safely in many environments.The Digital I/O Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
NI-5752B, 50 MS/s, 12-Bit, 32-Channel, Kintex-7 FPGA Support, Digitizer Adapter Module for FlexRIO
784062-01
Digitizer
The NI‑5752B is a digitizer adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a high-speed digitizer that simultaneously samples 32 channels at 50 MS/s. You can use the NI‑5752 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions. The NI‑5752B is compatible only with PXI FPGA Modules for FlexRIO that have Kintex‑7 FPGAs.
-
Product
PCIe-5764 , 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785962-01
FlexRio Digitizer
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer.
