Patient Simulators
generate known values for any or all of the following medical equipment which measure: invasive blood pressure (IBP), Arrhythmias, Respiration, temperature and Fetal simulation.
-
Product
ARINC 429 Test & Simulation Instrument for VXI
VXI-429
-
Avionics Interface Technologies
Programmable High/Low Speed Operation Concurrent operation of all Tx/Rx Channels at high data rates
-
Product
Load Simulator
-
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
Digital And Analog Call Simulation
-
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
Product
Resistor Simulation Card
SET-1210
-
The card has two ranges of values that meet the requirements of most functional test systems.The SET card is designed for applications in which resistive sensors provide information about parameters such as temperature (e.g. when testing motor controls)Each channel of the SET-1210 resistor simulation card is able to simulate the common short-circuit and no-load conditions, which can occur in a system due to faulty wiring or sensors.
-
Product
Solar Simulation Systems
-
PET Solar Simulators consist of a Light Source with a built-in Lamp Power Supply. The Solar Simulator has an ellipsoidal reflector that surrounds the lamp and collects most of the lamp output. The radiation from the lamp is focused onto an optical integrator that helps produce a uniform diverging beam. The beam is diverted 90° by a mirror onto a collimating lens. Special filters are placed between the mirror and the collimating lens to shape the radiation spectra to match various air masses. The output is a uniform beam that closely matches the sun's radiation spectra for a given air mass. Various models offer different areas of illumination. Each model can be manufactured to simulate the sun's radiation for different air masses.
-
Product
Synchro Simulator
SPA-CASE
-
Computer Conversions Corporation
The Synchro Simulator has two modes of operation: Static and Dynamic. The mode of operation is selected by the position of the mode switch. In the static mode, the thumbwheel switches select the output angle. In the dynamic mode, the speed and direction switches determine the rate and direction of synchro outputs. Self test circuitry continuously monitors and displays the output.
-
Product
DGS-65 Test Panel with FV Simulator / Bed of Nails
TA-650
-
The TA-650 is a new test fixture that will give any instrument shop the ability to conduct more detailed testing of the Collins DGS-65 directional gyro then was previously available.
-
Product
Channel Emulator/Fading Simulator
-
The channel emulator/fading simulator is a measuring instrument for reproducing the actual radio wave propagation environment of mobile communication.It reproduces the fading environment defined by 3GPP and virtual environment of multiple channels such as MIMO, HetNet.It will contribute to improving development and verification efficiency of the latest mobile communication system such as 5G NR, LTE-Advanced and IoT.
-
Product
ARINC-429 Multi-Channel Test & Simulation Module for Excalibur 8000 Family of Carrier Boards
M8K429
-
The M8K429 is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 8000 family of carrier boards. The module supports up to five ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word. The receivers allow for filtering and multi-storage modes of Data Words. The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention.The M8K429 comes complete with C-driver software library including the source code.
-
Product
Aircraft Simulator
ePlane PC
-
Pneumatic connections Ps, Pt and AoA (option)High accuracy, high resolutionSelectable pressure units: hPa; mb; in Hg; mmHg; ft; m; kts; km/h, ft/min; and Mach number and needle equipment visualisationSoftware executable under Windows 2000 and XPUSB cable for PC connection
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
PXI Analog Output/Current Loop Simulator Module - 16 Channel
41-765-001
-
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Transportation Vibration Simulator
KD-9363
-
King Design Industrial Co., Ltd.
Transportation vibration simulator is mainly used to check the product encountered in various vibration environmental of manufacture, assemble and install, transit and usage process. Especially all types of transportation vehicle. Common transport is road, railway, sea, air, etc. To identify whether the product have the anti-vibration capability to endure transportation environment and avoid arrival damage and harm the company reputation. It also can analyze the specimen structure and study its dynamic character.
-
Product
Oxygen Sensor Tester and Simulator
ST05
-
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
Product
4, 8, 16 Or 32 Channel ARINC429 Test And Simulation Modules For PMC
AMCX429-x
-
ARINC429 Test and Simulation module for PMC with 4, 8, 16 and 32 programmable Tx/Rx channels plus up to 8 Discrete Inputs/8 Discrete Outputs.
-
Product
Radar Threat and Target Simulation Unit
MS 1605
-
PTG is used to field/LAB evaluation / testing of RADAR. PC is used to control the profile of the target generation. PTG will work in both stand alone and remote mode. The PTG has keypad and LCD for stand-alone operation. The PC can interface the PTG through the USB link. The operator can communicate through the GUI to the PTG. MIL1553B Communication used for Interfacing with RADAR.
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
-
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
Product
Regenerative Grid Simulator
Chroma 61800
-
Chroma Systems Solutions, Inc.
Full 4 quadrant, fully regenerative, AC power supply designed for common electrical product testing such as home appliances and industrial electronics that require a programmable input source
-
Product
Transistor-Level Defect Simulator
Tessent DefectSim
-
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
Product
Avionics Network Simulation Systems
-
Avionics Interface Technologies
Support for up to 30 Network Interfaces (Fibre Channel & Ethernet)Time Synchronization with IRIG-B & IEEE 1588 Master ClocksFull Data Capture with time stampingData simulation with precise timing & synchronizationNetwork data replay from previously captured trafficPerform Network analysis using AIT's intuitive, easy to use, Ethernet & Fibre Channel simulation tools
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Simulation And Training
-
With more than 25 years of experience, Textron Systems Simulation and Training provides comprehensive end-to-end training solutions for air, land, sea, space, unmanned and electronic warfare platforms. We design, develop, and support integrated training devices, classroom courseware, virtual, live and constructive training, and software solutions. Our products and services support advanced platforms including C-17 Globemaster®, B-1 Lancer, F-35 Lightning II®, F-22 Raptor® and other high-value assets. Textron Systems also produces electronic, RF, and/or multispectral test equipment for verification and validation of these and various other air, land, sea, space, unmanned and electronic warfare platforms.
-
Product
ARINC 429 Test And Simulation PXI Module
PXI-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Graphical Debugging for Verilog, VHDL, and C++ Simulators
BugHunter Pro
-
BugHunter uses the SynaptiCAD graphical environment and supports all major HDL simulators. It has the ability to launch the simulator, provide single step debugging, unit-level test bench generation, streaming of waveform data, project management, and a hierarchy tree. The unit-level test bench generation is unique in that it lets the user draw stimulus waveforms and then generates the stimulus model and wrapper code and launches the code. It is one of the fastest ways to test a model and make sure that everything is working correctly. The debugger also has exceptional support for VCD waveform files.
-
Product
Distributed Simulation & Test Environment
-
Modular hardware and software architecture with multipurpose modules and components in a common and reconfigurable simulation and test environment easily adaptable to meet project‐ and customer‐specific requirements.
-
Product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
-
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
Product
Simulation Systems
-
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
-
Product
Resistor Simulator Card
CP-RESSIM-16
-
The CP-RESSIM-16 Resistor Simulator PCIe Card provides programmable resistance simulation across multiple channels for real-time test and validation environments. The card supports 16 independent digital programmable resistors, enabling accurate emulation of variable resistance conditions within a system.
-
Product
Advanced Thermo-Mechanical Simulators for Materials Testing
Gleeble 3000 Series
-
Comprises three distinct thermo-mechanical simulator models, each engineered to address specific materials testing requirements while maintaining the precision and reliability.
