Strain Gage Signal Conditioners
See Also: Strain Gages, Strain Gauges, Strain Gage Amplifiers
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
PXI Breadboard Module, 1-Slot, 78-Pin D-Type
40-220A-401
-
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
Suitable For Strain Gauge / Load Cell Sensors
SEM1600B -
-
Suitable For Strain Gauge / Load Cell Sensors
-
Product
Fracture Mechanics Clip-on Gages
-
3 models cover a broad range of gauge length, measuring ranges and temperatures, for fracture tests in compliance with various standards.
-
Product
PXIe Arbitrary Signal Generator and Transceiver
-
The Tabor Proteus Series P948xM, P9082M, P258xM and P128xM models are arbitrary signal transceivers based on the PXIe platform. The modules combine transmit, receive and digital signal processing capabilities in a single device. The modular, compact and cost-effective systems offer unique performance, various configuration options, innovative task-oriented programming and a user-programmable FPGA.
-
Product
Radio Monitoring and Signal Analysis
-
Shoghi has a full portfolio of products which fulfill the customer requirements for radio monitoring and signal analysis. Shoghi has a very robust SDR based wideband radio monitoring solution which can be implemented both in static or mobile versions for HF and VHF/UHF frequency bands. The Shoghi Radio Monitoring and DF system is the full-fledged product which provides the facilities for wideband signal reception and advanced signal analysis capabilities in addition to both wideband and narrowband D capabilities. The signal analysis capabilities include the ability to demodulate and decode both narrowband and wideband signals and advanced signal protocol analysis for detection of specific data protocols used in the intercepted RF signals.
-
Product
Mixed Signal Oscilloscope: 1.5 GHz, 4 Analog Plus 16 Digital Channels
MSOX4154G
-
The 4000 X-Series boasts 12.1-inch display, capacitive touch screen technology, InfiniiScan Zone touch triggering, 1-million-waveforms/sec update rate, MegaZoom IV smart memory technology and standard segmented memory.
-
Product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
-
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Signal Integrity Test Products
RoBAT RCI
-
*TDR & TDT, Measurement Capabilities*Impedance, Skew, Backdrill measurements*Automated Optical Inspection*DC Electrical Test*Now available with 4 heads*24 port (1 port per channel) TDR/TDT unit*Future capabilities – Fully automated VNA test (4 port S-Parameter Measurement)
-
Product
Signal, Patchcord, Receiver, 36", QuadraPaddle, 22 AWG White, Twisted Pair ( 5 Amps)
7-124439000-036
-
Signal, Patchcord, Receiver, 36", QuadraPaddle, 22 AWG White, Twisted Pair ( 5 Amps).
-
Product
Mixed Signal Oscilloscopes
-
A Mixed Signal Oscilloscope (MSO) is a combination Logic Analyzer and Oscilloscope. Since all inputs sample simultaneously, it is easy to see the timing relationships of the digital and analog components of your circuit. The extra channels also allow for more complex triggering. All of our MSOs have Oscilloscope triggering, Logic Analyzer triggering, SPI triggering and I2C triggering.
-
Product
Production Caller ID Signal Simulator
AI-80
-
The AI-80 is a fully programmable stand alone Caller ID signal generator designed for production environments. It is capable of generating signals for all FSK and DTMF based Caller ID standards. Includes general telephone signal analysis features and a highly flexible programming language for sophisticated and complex production testing sequences.
-
Product
Baseband Signal Generator
-
Find the right T&M solutions for applications requiring baseband signal generation. Our product portfolio includes the well-established baseband generator, supporting many wireless standards such as WCDMA, LTE, HSPA and WLAN802.11a/b/g/n/ac, using WinIQSIM2™. Our solutions selection also includes function generators.
-
Product
Multicore ARM + Digital Signal Processor
SI-AM572xDSP
-
The SI-AM572xDSP from Sheldon Instruments is an ARM plus Digital Signal Processor (DSP) carrier card with PCIe-104 and optional FMC expansion ports that may run Linux and be a C programmable platform intended for low power environments that require intensive computing in a cost sensitive solutio
-
Product
Signal 90 Series Modules
-
Use VPC's high density signal modules for seamless integration with COTS products. VPC signal modules fit all standard VPC Interconnect Solutions and allow for consolidation of multiple instrument connections within the space of a single or double receiver interface position.
-
Product
Car-to-X Signal Strength Emulator
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
Product
Stainless Steel Schaeffer Gage
SGO
-
The Series SGO Gages have dual English/metric scales with ±1.6% full scale accuracy. The Series SGO gages are designed with 304 SS housing, a 316L SS chamber and PTFE coated diaphragm for excellent chemical compatibility
-
Product
Pulse Signal Amplifier
VCH-606
-
The pulse signal amplifier VCH-606 is designed to multiply a single pulse or a sequence of pulses to 16 independent outputs. The impulse signal amplifier includes 16 independent channels with unity gain each for connecting consumers of impulse signals with an input impedance of 50 Ohm.
-
Product
Signal Generator, Audio, Compact, Handheld, 1 Channel, 20kHz, FM, US Plug
72-490
-
Highly versatile compact audio generator is perfect for sound system and speaker component testing. Its high precision and remote VCO input make it suitable for the serious test environment, yet its compact size and low cost make it suitable for any tool box. This device is designed to be connected to the line level of any consumer or commercial designed audio amplifier. While it is designed to be used with unbalanced inputs, it is also suitable for balanced equipment
-
Product
CATV & RF Signal Products
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber is a worldwide leading provider for fiber optic equipment, fiber optic test instruments and other data network & telecom products of communications, commercial, and consumer markets. The Company offers test and measurement systems and services to telecommunications service providers, cable operators, and network equipment manufacturers. In addition, the Company offers components, modules, and subsystems for Wireless, Telecommunication, Datacom, Power, Cable TV measurement instruments and utilities applications.
-
Product
Signal, Module, ITA, QuadraPaddle, iCon Series, 160 Position
510161101
-
Primary mating module 510160101. (May mate with other Receiver modules, as well.)
-
Product
PathWave Vector Signal Analysis Software
89600 VSA
-
A comprehensive set of tools for demodulation and vector signal analysis.
-
Product
Dynamic Signal Acquisition and Analysis
-
m+p Analyzer systems are available for field and laboratory use from 4 to many hundreds of measurement channels. From gathering simple time history data to narrowband (FFT) spectra, fractional octaves, wavelets, shock response spectra and much more, m+p Analyzer real time analyzers can be used with a wide range of instrumentation hardware including our own m+p VibPilot, m+p VibRunner and m+p VibMobile systems, National Instruments (CompactDAQ USB, PCI, PXI) and VTI Instruments (PCI). Low cost portable instruments to systems for distributed measurements can be configured for maximum flexibility. Measurement data from all sources are stored in a common format so it is easy to compare and handle results from any measurement source.
-
Product
PXIe-5832, 44 GHz, 1 GHz Bandwidth, MmWave PXI Vector Signal Transceiver
787728-01
-
The PXIe-5832 provides FPGA-based processing and the combined functionality of a vector signal analyzer and a vector signal transceiver. You can use the PXIe-5832 to perform stimulus and response measurements in the 5 GHz to 21 GHz and the 22.5 GHz to 44 GHz frequency ranges. Additionally, the PXIe-5832 features multiport configuration options that integrate solid-state mmWave switching to the 22.5 GHz to 44 GHz frequency range.
-
Product
PXIe-5442, 43 MHz Bandwidth, 16-Bit Onboard Signal Processing, 512 MB, PXI Waveform Generator
780109-03
-
PXIe, 43 MHz Bandwidth, 16-Bit Onboard Signal Processing, 512 MB, PXI Waveform Generator—The PXIe‑5442 is a 43 MHz arbitrary waveform generator capable of generating user-defined, arbitrary waveforms, standard functions including sine, square, triangle, and ramp, as well as signals that require onboard signal processing. Some of these signal processing operations include FIR and CIC interpolation filters, digtal prefilter gain, numerically-controlled oscillator, and I/Q mixing for quadrature digital upcoversion. The PXIe‑5442 also features advanced synchronization and data streaming capabilities.
-
Product
Signal Board Computers
PX1-C415
-
WINSYSTEMS’ PX1-C415 single board computer (SBC) is a PC104 form factor SBC with PCIe/104™ OneBank™ expansion featuring the latest generation Intel® Atom™ E3900 series SOC processors (formerly known as Apollo Lake-I). Its small size, rugged design and extended operational temperature make it a great fit for Industrial IoT applications and embedded systems in the industrial control, transportation, Mil/COTS, and energy markets.
-
Product
9kHz To 40GHz Signal Generators Module
-
Corech Microwave’s Ultra Wideband Signal Generators Module operates from 9kHz to 40GHz, featured with ultra wideband, CW/Pulse mode, ultra low noise of -105dBc/Hz@10kHz , low spurious and low consumption. They are very rugged and stable to be integrated in various systems.
-
Product
PXIe-5442, 43 MHz Bandwidth, 16-Bit Onboard Signal Processing, 32 MB, PXI Waveform Generator
780109-01
-
PXIe, 43 MHz Bandwidth, 16-Bit Onboard Signal Processing, 32 MB, PXI Waveform Generator—The PXIe‑5442 is a 43 MHz arbitrary waveform generator capable of generating user-defined, arbitrary waveforms, standard functions including sine, square, triangle, and ramp, as well as signals that require onboard signal processing. Some of these signal processing operations include FIR and CIC interpolation filters, digtal prefilter gain, numerically-controlled oscillator, and I/Q mixing for quadrature digital upcoversion. The PXIe‑5442 also features advanced synchronization and data streaming capabilities.
-
Product
Rosette Strain Gauges
-
Rosette Strain Gages have three measuring grids arranged at an angle of 0°/45°/90° or 0°/60°/120°
-
Product
SAT/CATV/TV Signal Analyzer
DSA 1491
-
9” full-color, high-resolution touch screen user interface simplifies complex measurement tasksRF inputs including satellite, cable and terrestrial along with ASI and IP inputsDigital RF measurements including average power/level, pre/post BER, MER, noise margin, spectral analysis and constellation
