Optical Attenuators
Reduce optical power by inducing loss.
-
Product
Switchable Optical Interleaver
-
In a switchable interleaver, there are two operation modes: *Mode A: All pass *Mode B: InterleaverIn Mode A, the system operates at any channel spacing, in which all channels pass through the device and output from one of the two output ports as if there is no extra device inserted. When the system is switched to Mode B, the device operates as a normal optical interleaver, such 50-100GHz interleaver. The working principle is schematically shown below. In Mode B, the device could be a standard symmetric interleaver, or an asymmetric interleaver. Channel spacings are not limitted to 50-100GHz. They can be any frequency pair: between N-GHz and 2N-GHz.
-
Product
Two-Way Optical Loss Test Set
KI23422OLF-INGAAS-APC
-
A Two-Way Optical Loss Test set (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on single mode fiber with an APC connector at 1310 / 1550 nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. The 650 nm VFL is on a separate port.
-
Product
- 10Base-T to Multimode Fiber Optic Transceiver
Model 373
-
FEATURES: Extend Lan's over 1 mile; Full Duplex Plug and Play - no software; Uses industry standard fiber optic cables; Impervious to lightning and surges; Total electrical isolation; 10Base FL compatible. Now you can break the distance barrier of Ethernet based Local Area Networks and achieve total system safety from electrical interference and surges.
-
Product
PXI Express High Speed Optical FPGA Board
HSS-8324-DSP
-
The Conduant HSS-8324 FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its two 12-lane HSS interfaces while performing complex calculations. The PXIe interface provides a theoretical maximum throughput of 8 GBps (simultaneous in and out) while each HSS port (12 lanes up to 16 Gbps per lane) supports a full duplex transfer at theoretical rates over 190 Gbps.
-
Product
Fourier Transform Optical Spectrum Analyzer, 350 - 1100 nm
OSA201C
-
Thorlabs' Optical Spectrum Analyzers (OSAs) perform highly accurate spectral measurements. Compatible with fiber-coupled and free-space light sources, these compact benchtop instruments suit a wide variety of applications, such as analyzing the spectrum of a telecom signal, resolving the Fabry-Perot modes of a gain chip, and identifying gas absorption lines. Many commonly available OSAs use grating-based monochromators, which have slow acquisition times due to the need to mechanically scan the grating and average out noise at each wavelength. Thorlabs' OSAs acquire the spectrum via a Fourier transform using a scanning Michelson interferometer in a push/pull configuration. This approach dramatically improves the acquisition time, enables a high-precision wavelength meter mode with 7 significant figures and ±1 part-per-million accuracy, and allows the included software to provide robust statistical analysis of the acquired spectra, as explained in the Design tab.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber
40-852A-318-HI
Multiplexer Module
The 40/42-852A-318-HI is a PXI/PXIe 8-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Optical Filters
-
INPHORA offers calculation, development and production of unique Optical Filters designed to match exactly to the requested parameters or to fit to the given application.
-
-
Product
Intelligent Optical Power Meter
FPM300 Series
-
Shanghai Tarluz Telecom Tech Co., LTD
Auto-wavelengths Recognition, Referencing Function, Computer Supported, used with FLS300 series Laser/Light Source.
-
Product
Optical Power Meter & VFL & RJ45 Network Test
TM263N
-
◇ Added Network Cable Test ◇ Accurately test whether a single network cable transmits signals normally ◇ Self Calibration ◇ Set the Auto Off ◇ Wavelength Memory function after turn off the tester ◇ High Accuracy, high ,High sensitivity, high linearity ◇ Stable VFL Output ◇ USB Charge port ◇ FC,SC Connector ◇ 18650Li-ion Battery ◇ Lower power consumption design, long standby time ◇ Rubber Out shell, increased the protective properties for field work
-
Product
Fiber Optical Switch at Single Mode Latching 1310/1550nm 5V with LC/PC Connector
SUN-FSW-1x2H
-
Guilin GLsun Science and Tech Group Co., LTD
GLSUN 1×2H Mechanical Optical Switch Fiber Switch Features·Low Insertion Loss·Wide Wavelength Range·Low Crosstalk·High Stability, High Reliability·Epoxy-free on Optical Path·Latching and Non-latchingGLSUN 1×2H Mechanical Optical Switch Fiber Switch Applications·R&D in Laboratory·System Monitoring·OADM·MAN (Metropolitan Area Network)·Network Security and MonitoringGLSUN 1×2H Mechanical Optical Switch Fiber Switch SpecificationsParameters Unit SUN-FSW-1×2HWavelength Range nm 1260 ~ 1650Test Wavelength nm 1310 / 1550Insertion Loss 1, 2 dB Typ: 0.8 Max: 1.0Return Loss 1, 2 dB SM ≥ 50Crosstalk 1 dB SM ≥ 55PDL dB ≤0.05WDL dB ≤0.25Repeatability dB ≤±0.02Operating Voltage V 3.0 or 5.0Durability Cycles ≥ 10 MillionSwitching Time ms ≤8Optical Power mW ≤500Operating Temperature ℃ -20 ~ +70Storage Temperature ℃ -40 ~ +85Relative Humidity % 5 ~ 95Weight g 14Dimension mm (L )22.5×(W)11.8×(H)10.2 ±0.2Note: 1 Within operating temperature and SOP.2 Excluding Connectors.
-
Product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Multi-Mode, 62.5/125 Fiber, SC Connectors
40-855A-212-M
Multiplexer Module
The 40/42-855A-212-M is a PXI/PXIe 2-channel multiplexer with SC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Fiber Optic Temperature Sensor with the EasyDisk
The TPT-62
-
The TPT-62 fiber-optic temperature probe family employs industry standard 62.5µm core OM1 fiber optic for highly improved optical, mechanical, and reliability properties over legacy 200 µm core (1st generation) fiber optic sensors. The EasyDisk sensor tip assembly ensures IEC60076-2 (Annex E) compliant installation and enables quick insertion of the probes into the spacers within the windings of transformers.
-
Product
FMC for High Speed Optical Communication Dual QSFP+ FMC
FMC424
-
Sundance Multiprocessor Technology Ltd.
The FMC424 is a dual QSFP+ FPGA Mezzanine Card. Electrically compliant with the VITA 57.1 standard the FMC424 is compatible with 4DSP FPGA carrier cards offering High Pin Count connectors. It also allows for the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC424, thus offering users with the ability to build a complete high speed data acquisition, waveform generation and optical communication solution while using a single FMC site on an FPGA carrier card.
-
Product
Optical Parametric Oscillators
-
Our optical parametric oscillators are the most advanced in the industry, with leading technology plus a range of options to suit every system and customer need.
-
Product
Variable attenuator
-
Optimum for simulation of wireless communication equipments, such as handover test, dynamic motion test and receiving sensitivity test. Moreover, optimum for the simulation of the receiving trouble by the rainfall attenuation in BS/CS digital broadcasting.
-
Product
Optical & Vision Systems
-
Usually made up of every component that is needed to acquire and analyze an image in order to perform the intended task.
-
Product
Fiber Optic Type Chemical Solution Concentration Monitor
CS-100F1 Series
-
The CS-100F1 Series is equipped with fiber optics cable based on the CS-100 Series. It offers real-time, in-line measurements by directly integrating the sample cell into the cleaning system piping and by using a fiber optic cable for light signal transmission. A single concentration monitor can take up to four measurements and monitoring of multiple chemical solutions in a single-bath or single-wafer cleaning system is also possible.
-
Product
RGB Laser Illuminance, Luminance & Optical Power Meters
TM6102/TM6103/TM6104
-
Accurately evaluate the white balance of displays that use lasers by measuring centroid wavelength and optical power, which are key characteristics in the evaluation of laser light sources. Designed to adjust and inspect RGB lasers. Meters measure radiant illumination, centroid wavelength, illuminance, luminance, chromaticity, Radiant flux (optical power) and luminous flux.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber, FC/APC Connectors, With Interlock
42-852A-018-HI
Multiplexer Module
The 40/42-852A-018-M50-HI is a PXI/PXIe 8-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Dispersion Compensation Optical Fiber Module
DCM-G.652-C-Fxx
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai and DCM-G.652-C-Fxx dispersion compensation fiber module, is negative dispersion compensation based on optical fiber technology, can effectively compensate for G.652 standard single-mode fiber transmission band of 1525 ~ 1565nm dispersion and dispersion slope characteristic.
-
Product
Galvanometer Optical Scanner
-
Citizen Chiba Precision Co., Ltd.
High performance and high reliability galvanoscanner (or called as galvanometer/galvanomotor/galvanoscanner motor) with high accurate optical analogue sensor which we newly developed.
-
Product
47~1200MHz FTTH CATV AGC Optical Receiver
H1222G
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H1222G, the operating bandwidth of 47 ~ 1200MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver, Whether used in analog television or digital television. Due to the built-in optical AGC, at high optical power receiver, played limiting output, so H1222G in the received optical power over a large dynamic range of +2 dBm ~ -20dBm, and have excellent properties.
-
Product
OPTICAL PHASE NOISE TEST AND MEASUREMENT SYSTEM
-
OEwaves’ HI-Q® Optical Test Measurement System utilizes a homodyne methodology for automated measurement capable of testing ultra-low phase noise laser sources. The user friendly test system is capable of rapidly measuring laser phase noise and estimating its FWHM linewidth down to < 3 Hz without complex setup or reference lasers normally required to make such a narrow linewidth measurement.
-
Product
Plastical Optical Fiber
POF
-
POF (Plastic Optical Fiber) is a new, convenient, effective, and economical method to construct optical networks at small office or home. A visible red light of 650 nm is utilized in this application so users can easily see the light at the cutting edge of the POF. Major application here is 100Mbps Fast Ethernet over POF implemented by distinct media converter or switches.
-
Product
Optical, Color And Electrical Integrated Test System
-
Hangzhou Hopoo Optoelectronics Technology Co., Ltd
Our individually calibrated LED spectroradiometers provide fast and accurate results for actual light measurement applications. It only takes a few seconds to measure and view the results directly on the display, or use the optional analysis and automation software for more in-depth research. Using the HPCS6500 Spectroradiometer, you can measure any or all of the following optical quantities:
-
Product
Optical Components for Custom Spectroscopy
-
HORIBA offers a wide variety of optical accessories. We have optical choppers which pulse continuous light sources. Explore our order sorting filter wheels for spectrographs and monochromators. Choose from our optical fibers and light guides, with flexible light delivery, single fibers, fiber bundles, and liquid light guides. And select from our lens and mirror-based sample compartments.All of these accessories are compatible with our various optical components. Our optical accessories allow us to complete a custom solution for your unique configuration requirements and a variety of spectroscopy applications. HORIBA offers more choices to ensure you can select the best optics for your needs.
-
Product
Fiber Optic Sensor Systems
-
Fraunhofer Institute for Telecommunications
Fiber-optic and photonic measuring systems open up innovative measuring and control technology concepts for a wide variety of applications. They play a major role in optimizing energy efficiency and are important technological innovation drivers for new and future-oriented markets.In the Department of Fiber Optic Sensor Systems of the Fraunhofer Heinrich Hertz Institute, the focus of application-oriented research is on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication capability as well as extremely low power consumption or even a self-sufficient power supply.In the Department of Fiber Optic Sensor Systems at the Fraunhofer Heinrich Hertz Institute is focused applied research on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication skills as well as an extremely low power consumption, or even a self-sufficient energy supply.
-
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Multi-Mode, 62.5/125 Fiber, SC Connectors
40-855A-222-M
Multiplexer Module
The 40/42-855A-222-M is a PXI/PXIe dual 2-channel multiplexer with SC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
