Remote Terminal Unit
Collects data from data acquisition (DAQ) devices and transmits the information to the main test system via a network.
-
Product
PXI/PXIe Fault Insertion Switch, 32-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-212
Fault Insertion Unit
The 40-190C-212 (PXI) and 42-190C-212 (PXIe) are fault insertion switches with 32 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Interface Units
-
intelligent, microprocessor controlled, data acquisition and lambda measurement unit for up to 6 wide band UEGO sensors. It is based on the sensor node and can be used as part of the DATA
-
Product
3U OpenVPX Sensor Interface Unit
SIU34
Sensor Interface Unit
The SIU34 is a highly configurable rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, communications, Ethernet switching and processing. The SIU34 leverages NAI’s 3U OpenVPX™ boards to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Coaxial Open, 2.4 mm (m)
85141A
Terminator
The Keysight 85141A coaxial open is used for establishing measurement planes for known reflection phase and magnitude in 50-ohm coaxial systems. It has a 2.4 mm male connector.
-
Product
PXIe Short SMU
52403P
Source Measure Unit
Chroma's 52403P is a PXI Express Short Pulse SMU (Source/Measure Unit) designed for fast, precise and reliable sourcing and measurement of thermo-sensitive devices such as high-power laser diodes (LD). Integrating a high-speed pulser, a high precision SMU and a DAQ module into a single PXIe SMU, the 52403P can measure both the LIV and the low-level leakage current of a high-power LDs.
-
Product
Interface Unit
CMM Automation
-
The Aberlink automation interface adds the capability for Aberlink 3D programs to be remotely controlled and monitored using an external system allowing any Aberlink CMM to be integrated with an automated component handling system, whether this be a fully controlled, PLC driven manufacturing system, a robotic loader or just an automatic bar feeder. The package comprises of an optically isolated digital I/O system and a software module that enables the software to be setup to follow a defined operating sequence to allow the automated operation.
-
Product
Inertial Measurement Units
-
Safran manufactures inertial measurement units and sets a new standard for precision and performance by utilizing our proprietary inertial sensor technology. Our IMUs are engineered to excel in the Defense, Industrial, Aerospace, and Commercial sectors with the highest performing ITAR-free products commercially available.
-
Product
Display Unit
Epec 6107
-
Epec 6107 Display Unit enables remote connectivity and has an excellent sunlight readability, wide viewing angles and high-end graphics. Epec 6107 also has versatile communications interfaces and it offers multiple possibilities for remote access. With its 7″ resistive touch screen it is compact, yet big enough to fit many purposes. Epec 6107 supports both panel and pedestal mounting. Together with Epec’s IoT Services you’ll get the fastest to configure and most reliable IoT system/remote management solution in the market.
-
-
Product
Manual Clemen Unit
Elcometer 3000
-
The Elcometer 3000 Manual Clemen Unit is a robust and simple to use instrument for evaluating the resistance to scratching of a coated surface.
-
-
Product
Control Units
-
For integration into a larger system or for automated measurements, the gain control unit for automated systems lets you control the settings of the intensifier attachment. The control unit uses standard TTL and analog signals for communication, allowing the user to switch the intensifier on or off, alter the gain and the anode current limit of the image intensifier without the need of software integration.
-
Product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix Topology Without Column Protection Resistors
782385-09
Terminal Block
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Speaker/Receiver Unit Tester
BK2120A
-
Our new, upgraded BK2120A is a complete system for testing both acoustical features and rub & buzz in microspeakers, receivers and earphones or earbuds. It is just as fast and easy to use as our "Classic" BK2120A speaker tester, but because it connects with a LAN cable, you can use it with a notebook, as well as a PC. Its new modular design also makes maintenance more convenient and the redesigned BS1123 software is even easier to use and more versitile than the old version. You still get both graphical and numeric test data but with more display options than before. We still customize our machine to your special needs and of course you can still save your data to analyze later. Easier setup, improved design, more features, easier to use: we expect our new BK2120A to be even more popular than the original!
-
Product
Delay Unit
V972
-
The Mod. V972 is a 1-unit wide VME 6U module that houses a delay unit with a range from 0 to 31.5 ns with a 2.6 ns offset. The delay can be set in 0.5 ns steps via front panel toggle switches.
-
Product
Remote mount PMC
PMC-Extend-IO
-
PMC-ExtendIO-II provides a 32/33 - 64/66 extension between a PMC and Host. Any combination of PMC PCI bus speed and data width can be accomodated. With 66 MHz implementations cable lengths may be restricted compared to 33 MHz usage.
-
Product
Remote I/O
-
ADAM remote I/O are categorized into 5 families: IoT/OPC UA Ethernet I/O, Modular I/O system, RS-485 I/O and Serial/USB Converters/Repeaters.
-
Product
Extension Unit
ZET 452 MP
-
The ZET 452 MP extension unit improves the capabilities of electric circuit parameter control devices:*increases the number of measuring circuits;*makes it possible to build distributed systems for cable networks checking.
-
Product
Switch Analyser Unit
SA5A
-
The SA5A has been developed for professionals users that wish to fully analyse their medium voltage circuit breakers.
-
Product
Unit Testing
-
Hitex offers a unit testing service for C/C++ application source code using the well-known test tool TESSY. For this service, the customer provides their source code of the C/C++ functions to be tested, ideally along with the specifications of the functionality and comprehensive comments in the source code.
-
Product
PXI Remote Mount Triple SP6T Multiplexer 26.5GHz 50, SMA-2.9, Terminated
40-785B-533-TE
Multiplexer Module
The 40-785B-533-TE is a remote mount triple 6-channel 26.5GHz terminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
-
Product
Load Support Unit
LSU220A
-
The LSU220A is a general purpose load support unit designed to act as a permanent power supply to maintain backup battery systems whilst alternative sources of power are either impractical or unavailable, such as running diesel engines during maintenance programs.
-
Product
Instrument Test Unit
-
Instrument Test Unit For Advanced Inertial Sensors (INTU) is used for testing and evaluation of Ring Laser Gyro (used in GSLV/PSLV launch vehicles), that detects the angular displacement during rotation. The INTU receives displacement signals from the sensor (RLG) to evaluate the sensor characteristics and also generates signals required towards initiating the action of the sensor.
-
Product
Battery Loading Unit
BLUe
-
BLUe series Battery Loading Units; portable instruments for controlled & monitored discharge of batteries. It is designed for integrated site discharge test, design & QC test and also for monitoring discharge process of battery bank with connected load. Single autonomous unit having inbuilt display, keypad and wireless communication with PC makes it very easy to use. It comes in different configurations ranging from 12V to 380V discharge voltages and 50A to 300A discharge currents. Various options are available to control & monitor the discharge process. With the help of optional Cell Monitoring Unit - CELLMon, voltage of each individual cell can be monitored & data sent to main BLUe unit and then from main unit to PC via wireless communication. Each BLUe unit is supplied with PC downloading & analysis software for real time monitoring of discharge process.
-
Product
Electronic Units
-
Electronic units for field installation and mounting rack installation control the actuators. They are fed with 115 or 230 V AC. A local control panel allows for easy basic settings.
-
Product
Terminal Equipment Simulator
AI-5620
-
The AI-5620 simulates a single port two wire analog TE (Terminal Equipment) or CPE (Customer Premise Equipment) device. It is designed to measure and analyze signals generated by a CO (central office) line card, VoIP terminal adapter FXS port, or any device utilizing a SLIC (subscriber line interface circuit).
-
Product
Inertial Measurement Units
IMU
-
Analog Devices inertial measurement unit (IMU) sensors are based on multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors. Our technology reliably senses and processes multiple degrees of freedom, even in highly complex applications and under dynamic conditions. These plug and play solutions include full factory calibration, embedded compensation and sensor processing, and a simple programmable interface.
-
Product
Compact Remote Station
Model 45.50
-
The CRS System consists of amplifiers, VCO's, I/O systems, multiplexers, digitizers, and radios. Electrical connection between the modules is provided through a ribbon cable harness within the enclosure.
-
Product
Control Unit
Epec 5050
-
Epec 5050 Control Unit is ideal for applications that require plenty of I/O and enhanced algorithms. Epec 5050 control unit has also a large memory and its I/O is widely programmable. For example, PI pins’ threshold voltage can be selected and many inputs have pull-up/pull-down selection.
