Testers
find the limits of a design and assure designed requirements.
See Also: Test, Testing, Specimen, Audio Testers, Automotive Testers, Battery Testers, Cable Testers, Component Testers, Checkers
-
Product
Socket Outlet Tester
-
Using the new Testavit Schuki 1 LCD and 3 LCD, specialists easily check to see if sockets, cable drums or connecting cables are correctly connected in 230 V installations. Due to three LEDs, the connection status can be quickly and clearly determined. In addition, through the finger contact, it can be tested to see whether an impermissible, high contact voltage is applied at the protective earth connection. In addition, using the Testavit Schuki 1 LCD, a 30 mA FI circuit breaker (RCD) can be triggered via a pushbutton.
-
Product
Network Cable Tester
LightingJoG Rack 8
-
Sensational 19 inch 2U rack mount Lighting/Network cable tester with SINGLE & DOUBLE ended testing, memory and intermittent fault detection.
-
Product
Portable Electricity Meter Testers
EE-120A-1S
-
The EE-120A-1S unit consists of a single-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types single-phase electricity meters using the voltage of the site. The meter error can be measured for active, reactive or apparent energy, in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the site – with direct measurement or with optional current clamps.
-
Product
TACAN/DME Station Tester
EDST300
-
The R&S®EDST300 TACAN/DME station tester is an analyzer designed for commissioning, testing and servicing pulsed terrestrial navigation systems.
-
Product
Polarity Indicator Circuit Tester
CT8007
-
No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance electronic circuitry. Negligible current draw ( 1 microampere) is 30,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 6 and 28 Volt DC in battery powered systems
-
Product
Compact Professional IC Tester
ChipMaster
-
The ABI ChipMaster Compact Professional is a low-cost, hand-held out-of-circuit IC tester. The ChipMaster is designed for testing digital ICs with up to 40 pins through a ZIF socket (see LinearMaster for analogue devices). A range of adapters is also available for SOIC and PLCC devices.
-
Product
Packaging Compression Tester
KRD101 series
-
KRD101 Series Packaging Compression Tester is designed to evaluate the compressive strength of packaging in order to prevent the product from deforming or being damaged during handling, stacking, storage, and transportation due to insufficient packaging strength. This machine is one of the main testing equipment for corrugated packaging performance and comprehensive indicators, and is an ideal testing equipment for papermaking, packaging, commodity inspection, scientific research and other departments.
-
Product
Programmable Ground Resistance Tester
-
AllWin Instrument Science and Technology Co., Ltd.
Executive test in 40A/60A of UL60950-1Test resistance range 0~510m ohmOutput current range 5~40A
-
Product
Cobb Absorbency Tester
DRK110
-
Shandong Drick Instruments Co., Ltd.
DRK110 Cobb Absorbency Tester is used to test the absorbency of paper and cardboard according to related standards.
-
Product
Solder Wettability Tester
5200TN
-
Amid the rapid progress in miniaturization of electronic components in high-density mounting, a long-established company that has been manufacturing solder wettability testers for about 40 years has developed a solder wettability tester compatible with the latest micro electronic components. and is the top model in the history of solder checkers with improved operability. * Wetting stress is proportional to the circumference of
-
Product
Coupler And Decoupler Used With Lightning Impulse Simulation Tester
-
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
Product
Transformer Polarity Tester
PMT20030
-
Power Measurement Technologies Inc.
A hand held instrument for polarity identification of current, voltage and power transformers with an operable ratio range from 1:1 to greater than 5000:1.
-
Product
AUTOMATIC WINDING TEST SYSTEM
VE9036SU
-
6 CHANNEL Microprocessor based Automatic Test System for Automobile Coils, Magnetos, Alternator, Motor Winding. Can Test : Impulse Winding Tester (IW), AC/DC HiPot, Insulation Resistance (IR), Inductance (L), DC Resistance (DCR)
-
Product
Multifunction Earth Tester
MT-200
-
Multifunction earth tester for measuring earth resistance, protective conductors’ continuity, insulation up to 1000V, with touch-screen display and integrated Wi-Fi
-
Product
Power Bank Capacity Tester
TOB-BTS-6V4A
-
Xiamen Tob New Energy Technology Co., Ltd
Power Bank Tester Used For Power Bank Capacity,Voltage And Cycle Testing. The TOB-BTS-6V4A Power bank tester is used for power bank quality detection, it can test the power bank capacity, voltage and life cycle performance with connecting computer.
-
-
Product
USB SOCKET TESTER
MDPPTSTUSB
-
*Provides the user with a simple way to test a USB socket on a vehicle*Mini probe will light up when 4.4V - 5.25V is detected
-
Product
Hail Impact Tester
HIT
-
Hailstorms can cause severe damage to modules and collectors. Our test stand enables you to carry out tests according to international standards. The hail impact test stand uses an air-pressurized launcher that shoots ice balls representing hailstones of a predetermined size at the module or collector mounted on the support frame.
-
Product
Air Quality Tester
-
Choose a CO or CO2 meter to perform tests in labs, hospitals and plants. These meters help ensure the air quality is safe by warning you with visual and audible alarms when gasses exceed safe levels.
-
Product
Software
AFK-9110
-
Wired testers of the TEST-9110 series have been produced in series since 2006 and are well known to Russian and foreign consumers. As of the beginning of 2017, more than 250 sets of TEST-9110 series systems are in operation. Up to now, two types of software have been supplied with them: this is the AKM software and the cyclogram translator software. Now these programs have been revised into the AFK-9110 software.
-
Product
Sharp Edge Tester
SE400
-
The Sharp Edge Tester is used for determining the sharpness of edges of electrical equipment and other consumer products. A special tape is mounted on a spring loaded arm and dragged over the sharp edge. The tape is then inspected for damages.
-
Product
MBT 1000 Series
MBT 1000 EUROSYSTEM | VP 610012
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MBT 1000 EUROSYSTEM roller brake tester is used to test the brakes of single and two-lane vehicles such as motorcycles, trikes and quads with a wheel load of up to 1.0 t. Due to its short roller spacing, it is also especially suitable for testing small two-wheelers. Its MAHA modular design enables an optional motorcycle clamping and holding device for the rear and front wheel, whose removable clamping jaws ensure simple and rim-friendly testing.
-
Product
UAT testing
-
A successful UAT is crucial for deploying systems with no errors and business risks. However, implementing UAT in an agile environment might lead to frequent and reduced cycles of testing. This mandates UAT testers to develop skills of optimized testing techniques, automation and work in collaboration with the development and QA teams.
-
Product
Crimp Tester
M004
-
To calculate the crimp in yarn affected by knitting or weaving, to determine actual yarn usage.
-
Product
Cupping Tester
PCE-CPT 20
-
PCE-CPT 20 is a cupping tester, or coating flexibility tester, used for testing the adhesion, elongation and deformability of paints, lacquers, varnishes, powder coatings and other surface coatings on metal sheets. Used in manufacturing production, paint shop and quality control applications, the PCE-CPT 20 cupping tester aids in determining coating strength, durability and elasticity. A mandatory test in Qualicoat and QIB accredited quality control laboratories, a cupping test, also referred to as an Erichsen test or dent test, uses a spherical punch to deform a sample. This deformation results in a cup-like bulge. When using the PCE-CPT 20 to perform a cupping test in accordance with the ISO 1520 standard, the sample should be placed coating side up so that the 20 mm spherical punch presses against the uncoated underside of the metal sheet. The cupping test is terminated when small cracks and/or detachments are observed on the bulged part of the sample. The PCE-CPT 20 cupping tester's easy-to-read display shows the bulge deformation distances that can be used to determine the coating's flexibility rating.
-
Product
Water Testing
-
Benchtop conductivity meter, benchtop dissolved oxygen meter, benchtop ion meter, benchtop multi-parameter water quality meter, benchtop water hardness meter, BOD meter, COD analyzer, conductivity tester, dissolved oxygen tester, multi parameter water quality analyzer, online conductivity controller, online dissolved oxygen controller, online pH controller, ORP tester, pH meter (benchtop), pH meters (portable), pH tester, portable conductivity meter, portable dissolve oxygen meter, portable multi parameter water quality meter, portable water hardness meters, salinity tester, TDS tester, TSS meter, trubidity meter, water activity meter
-
Product
Digital Harmonics Clamp Tester
HWT-301
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Harmonics and leakage current measurements.*Up to 25th harmonics current and voltage measurements.*True rms reading for ACA and ACV.*Data-hold and Auto power off function.*Conform to IEC safety requirements.
-
Product
DC High Voltage Break Down Tester
-
High Voltage Breakdown Testers also known as Hipot Testers or Insulation Testers are a necessity for any Transformer testing, Substation equipment testing, Cable testing, Panel testing and testing of various insulating materials. Insulation testing is very important to ensure and maintain the safety of electrical equipments and also for the safety of operator.
-
Product
Leakage Current Tester
-
Test Voltage : - 1V to 500V DC settableAccuracy : ± 1% of set Value ± 1digitLeakage Current : - Accuracy - ± 0.5% ± 1digitDigital Model – 19.99μA / 199.9 μA / 1.999mA / 19.99mAAnalog Model - 10μA /25μA/100 μA/1mA/2.5mA/10mASeparate Indication for Charge / Measure and Discharge modeAvailable in Digital Version Also
-
Product
6-600V 2-Pole Voltage Tester
1998B
-
Peaceful Thriving Enterprise Co Ltd
The 2 pole Voltage Tester provides a clear indication of AC or DC voltages levels via bright LED's from 6V to 600V. It is constructed in accordance with the latest safety standards and is ergonomically designed which is durable enough for both industrial and domestic uses.
