Regulators
-
Product
Automatic Capacitor Batteries
-
Lifasa - International Capacitors, SA
The batteries of capacitors for automatic AT are designed for those applications in which the power levels in the AT network are variable. This type of equipment, with a number of steps normally between 2 and 4 to avoid phenomena in the installation resulting from the connection and disconnection of the capacitors in the electrical network, is controlled by a type MCX regulator, which tunes and regulates the input of the steps according to load levels, taking into account the expected waiting times of AT that between consecutive connections is 600 s., this time we can reduce it to less than 10 s. if we install TP for fast download.
-
Product
High Current SMU 600/1200/2400 A
AXC85xx
-
Generate extremely short, fully regulated current pulses in 4 ranges. At the same time, carry out measurements directly on the DUT with the integrated VMU and CMU. Perfect for rapid semiconductor tests during production.
-
Product
Semiconductor Testing
-
Teradyne’s semiconductor test portfolio is transforming the way you test chipsets for automotive, industrial, communications, consumer, smartphones, and computer and electronic game applications. Semiconductor devices span a broad range of functionality, from very simple low-cost devices such as appliance microcontrollers, operational amplifiers or voltage regulators to complex digital signal processors and microprocessors as well as memory devices.
-
Product
Temperature and Humidity Regulator
H3021-2
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Temperature and Humidity Regulator
H3331
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
Product
High Voltage SMU
-
Source and Measurement Units (SMUs) are devices that generate voltages or currents and can measure them simultaneously using the integrated measuring units (VMU, CMU).High-voltage SMUs work as a regulated voltage source and are able to generate very high output voltages.
-
Product
Pumps
-
Our broad range of pumps and fluid system components for laboratory, analytical, and industrial process applications includes peristaltic pumps, positive displacement pumps, metering pumps, centrifugal pumps, and more. And we don’t stop with the pump, we also offer the tubing, fittings, filters, regulators, flowmeters, and gauges to complete your fluid handling system.
-
Product
TDK Test Services
-
TDK Test Services offers testing to domestic and international EMC test regulations, including IEC, ISO, CISPR, and SAE. Test services are offered in our 3m semi-anechoic chamber, 3m fully-anechoic chamber, 10-meter open area test site, and our shielded conducted test chamber.
-
Product
PXI Dual Programmable +10V Power Supply
41-735-001
Programmable Power Supply
A single slot power supply module providing two programmable positive output voltages. The module provides high quality regulated voltages from a linear regulator to ensure low levels of output noise.
-
Product
Rapid Temperature Change Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is the company capable of offering a series of Rapid ESS Test Chamber,Rapid Temperature Change Test Chamber,Environmental stress screening (ESS) test chamber,Environmental stress screening test chamber,Temperature Change Test ChamberEnergy-saving design: Adopting PID + PWM principle of VRF (refrigerant flow control) technology to achieve low-temperature energy-saving operation (electronic expansion valve according to thermal energy conditions refrigerant flow servo control technology) low temperature working state, the heater does not participate in the work, through PID + The PWM regulates the flow rate and flow direction of the refrigerant, and regulates the three-way flow of the refrigerant pipe, the cold bypass pipe, and the hot bypass pipe to achieve automatic constant temperature to the working chamber. This method can reduce energy consumption by 30% under low temperature conditions.
-
Product
1U Power Supply ModelsAC-DC Single Output
-
Conserve space with mini-modules as small as 2.3" x 1.8" x 1.0". Models with outputs ranging from 1 to 75 volts, and from 30 mA to 2.5 amps are available. All feature excellent regulation and ripple parameters, and are short circuit protected.
-
Product
Supervisory Software
-
A supervisory program or supervisor is a computer program, usually part of an operating system, that controls the execution of other routines and regulates work scheduling, input/output operations, error actions, and similar functions and regulates the flow of work in a data processing system.
-
Product
Controllers
-
Omega offers PID controllers, level controllers, thermostats, pressure regulators, and much more. All our products are industrial-grade and made to deliver dependable performance for years to come.
-
Product
Bench/System Higher Voltage DC Power Supply With Linear Regulation. Single Output 90 Watts, 120V Or 250V, With/without Remote Interfaces
PLH Series
-
Single output 120V 90W or 250V 94WLinear regulation - for the best performanceUltra-compact design - uses up less spaceTrue Analogue controls - for ease of useS-Lock function - instantly lock settingsV-Span function - customize the voltage rangeLow current range and current meter averagingDC output switches and "view limits" buttonSelectable remote sense terminals
-
Product
RCD Testers
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
Product
Multi Output Regulated DC Power Supply
LQ6324T
-
- Low cost general purpose laboratory bench unit.- Fully protected against overload and short circuit.- Three independent outputs electrically isolated from each other.- 5V/5A with over voltage crowbar protection for digital ICs.- Electrically floating outputs up to 500V DC w.r.t. ground.- Compact modular construction.- Precise regulation, low ripple and noise for both constant voltage and constant current operation.- Quality components and conservating ratings for high reliability and long life.
-
Product
Walk-In Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Energy-saving design: Adopting PID + PWM principle of VRF (refrigerant flow control) technology to achieve low-temperature energy-saving operation (electronic expansion valve according to thermal energy conditions refrigerant flow servo control technology) low temperature working state, the heater does not participate in the work, through PID + The PWM regulates the flow rate and flow direction of the refrigerant, and regulates the three-way flow of the refrigerant pipe, the cold bypass pipe, and the hot bypass pipe to achieve automatic constant temperature to the working chamber. This method can reduce energy consumption by 30% under low temperature conditions. The technology is based on Danish Danfoss' ETS series of electronic expansion valves, which can be used to smoothly adjust the cooling capacity for different cooling capacity requirements, that is, to achieve the compressor cooling capacity adjustment when different cooling rate requirements are met.
-
Product
Motion Control
-
The ACE products in this segment enhance the quality of any type of movement. Anyone who wants to raise or lower loads, regulate the feed of an object to the precise millimeter or gently decelerate rotating or linear movements will find the right solution here.
-
Product
Full 4-Quadrant Grid Simulator
TC.ACS
-
The increasing number of alternative power sources like solar, wind driven or biological energy systems call for consistent and well demanding regulations for energy feed into the utility grid. Manufacturers of such systems have to test and to prove the compliance of their equipment. Grid simulators form an electronic equivalent circuit for the grid, but allow to vary all relevant parameters in order to test the behaviour and response of the equipment under test.
-
Product
Alternator Tester
ALTALYZER Tester
-
The Altalyzer tester is used to check the correct operation of alternators equipped with electronically controlled voltage regulators. In alternators of this type, the charging voltage is not constant, but varies depending on external factors such as: engine revolutions, number of current receivers, etc. The voltage at a given moment is determined by the motor controller by sending the appropriate information to the alternator.
-
Product
Diode Laser Driver
D200
-
The D200 is a compact, DC-coupled fast laser driver, providing up to 4 amps of regulated constant current. A built-in edge-triggered pulse generator produces up to 1 microsecond pulse widths and 2 nanosecond transition times, capable of driving lasers with forward voltages up to 9 volts. A pulse-follower mode is also provided, accommodating externally-defined trigger widths up to 100% duty continuous-wave (CW). Power, pulse width, drive current and differential triggering functions are accessible through a ribbon cable header for embedded OEM applications. A low-inductance laser drive interface permits direct laser connection or custom interposer and flex-cable attachment.
-
Product
DevOps Testing Services
-
The use of DevOps testing practices is aimed at bringing improved collaboration across teams and better changes in business response rate. ImpactQA follows an extensive skill set for structuring the right QA capabilities for DevOps. We are living in a fast-paced environment which comes with a shorter testing window. The inclusion of shift-left approach and an efficient team of development engineers permit quicker testing execution and improved code quality. Our continuous testing and crowd testing techniques are powerful testing methods that assist in upholding a DevOps environment within an enterprise. At ImpactQA, we deploy a systemized arrangement that regulates better time-to-market via DevOps testing solutions. Our motto is to bring augmented operational efficiency that is motivated through our DevOps testing professionals with their far-reaching expertise in Continuous Integration (CI) testing & Continuous Deployment (CD). We offer end-to-end automated solutions for sustaining Continuous Testing (CT) that functions with CI & CD tool
-
Product
Scienlab BMS Environment
SL101XA Series
-
A BMS assumes important safety, control, and regulation functions. Those functions include monitoring parameters such as voltage, current, temperature, and state of charge (SOC). A BMS also regulates thermal management, energy management, cell balancing, and performance.
-
Product
Film Frame Test Handler
4170-IH
-
High throughput ・High withstand load, and high thrust table ・Expansion of the strip attachment area ：260(L) X 300(W) [Withinφ300mm for WLCSP]・LOT control by barcode/2D code reader ・Easy device type exchange only test socket and display screen setting・Auto-cleaning function unit is installed to clean the socket at any desired timing.・8/12 inches ring conversion ・S2/S8 regulation compliance・SEMI G85 compliance・SECS/GEM compliance
-
Product
Temperature and Humidity Regulator
H3061-4
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Qualification Hardware & Sockets
-
Reltech Limited holds over 35 years’ experience in the design and manufacture of all types of qualification test hardware. Our advanced technology products include: HTOL Boards (Mother and Daughter cards) Burn-In Boards HAST Boards THB (humidity) Boards Burn-In Modules and frames Dynamic Driver cards (Digital, Analogue and Mixed signal) Back Planes Voltage regulator cards Custom electro-mechanical assemblies DUT Cassettes and test Fixtures
-
Product
Testing of Electrical Safety
-
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
Product
Linear Regulated Power Supplies (to 150 watts)
Gold Box "Infinity"
-
*Highly Configurable, with a seemingly Infinite number of Options*Any slot voltage from 1.5v to 150v is available*Remote Sensing*Open Sense protection*Isolated output*Short circuit and overload protection with enhanced surge capabilities*No minimum load required*Internal EMI Filtering*Pluggable connectors*Can be mounted on two surfaces in any orientation
-
Product
Automated Control System
TermoPress
-
Create a system for controlling and regulating the temperature of hydraulic press plates, as well as recording the current temperature and pressure values. Solution The system has the following basic functionality:configuring and setting the working parameters of presses;start and stop the technological process of the individual press;temperature control and pressure control;forming a timetable for the work of presses;registration of process parameters on an electronic carrier;archiving and viewing of archived data;construction of reports on the technological process in text and graphic form;Turn on and off the power of the press groups.
-
Product
VibA(8) Hand-Arm And Whole-Body Vibration System
-
The all NEW VibA(8) from Castle Group Ltd takes Hand Arm & Whole Body Vibration measurement to a whole new level! Ultra-simple to use and dedicated to compliance with the Control of Vibration at Work Regulations 2005, the VibA(8) delivers the ultimate practical solution to quantifying the vibration level of tools on your site.
