Regulators
-
product
Regulated Power Supplies, Output 0 to 24 VDC, 400 AMPS, 9.6 KW, P/N 5944C2
- Regulated Power Supply, 9.6 KW P/N 5944C2- Input: 220 VAC, 3 PH, 50/60 Hz- Output: 0 to 24 VDC, 400 Amps max- Duty factor: 100%- Ripple voltage: <3% across full output range- Setting: 0 – 100% current and voltage- Control: Constant current and voltage control- Ambient temperature: up to 95 degrees F- cooling: Forced air-cooled- Dimension: 17.6″H x 19.9″W x 21.6″D- Weight: 175 lbs.- Degree of protection: NEMA 2
-
product
Bench/System DC Power Supply With PowerFlex Or PowerFlex+ Regulation
QPX Series
Wide range of voltage/current combinationsUp to 80V and up to 50A within the same power envelopeLow output ripple and noise of <3mV rms at full powerHigh setting resolution of 1mVAnalogue control interfaces for voltage and currentBench or rack mounting, front and rear terminalsUSB and LAN (LXI) interfaces with GPIB optional (QPX600DP, QPX1200SP and QPX750SP)
-
product
Calibration Hangers And Weights
Calibrated Dead Weight are the official means by which torque analyzers and torque sensors are calibrated and are traced to National or International Standards, such as N.I.S.T, ISO and others. Many industries like as medical, aerospace, nuclear and others continuously calibrate their measuring equipment to comply with government regulations. For companies that prefer to have calibration capabilities in-house when their calibration requirements become extensive, they need calibration equipment.
-
product
BiGEN Power Supplies
BiRa Systems and TDK-Lambda collaborated to develop and support an accelerator laboratory family of programmable DC power supplies. The BiGEN family of power supplies provides many features including EPICS compatibility, interlock monitoring, precision current regulation, and air filter kits to fit the harsh accelerator environment. The BiGEN family of power supplies was based on the TDK-Lambda Genesys™ power supplies which can be configured in parallel and series for additional output power.
-
product
Multifunction Calibrator 15 ppm Basic Accuracy
MC142
Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using signals with various crest factors. Frequency modes enable selection of frequency, amplitude and duty cycle of the output signal. These are suitable for basic calibration of digital and analog oscilloscopes along with transient recorders. The calibrator is equipped to measure temperature with TC and RTD temperature sensors. Its built-in multimeter can be used independently or simultaneously with the calibrator output. Testing of transducers of various types, regulators and sensors can be performed, without the necessity to use any other measuring instrument.
-
product
Vehicle Emissions Laboratory
Trialon’s Vehicle Emissions state of the art testing facility is located in the heart of the Detroit Metro area. Our facility is equipped with the essential emissions equipment to simulate real driving conditions to meet the needs of national regulations. The test facility is staffed with talented technicians and engineers with over 50 year of combined experience.
-
product
Automatic Voltage Regulating Relay
NMC introduces low cost microcontroller based basic automatic voltage regulating relay, type : h-101.
-
product
Dual Vapor Gravimetric Sorption Analyzer
DVS Resolution
DVS Resolution’s key feature is the combined ability to precisely control and measure temperature and relative humidity while recording the highest resolution changes in mass. DVS Resolution uses a dry carrier gas typically nitrogen or compressed air for its operation. Digital mass flow controllers regulate flows of dry and saturated gases. Relative humidity is generated by precisely mixing dry and saturated gas flows in desired flow ratios which produce expected relative humidity. In a typical experiment a known concentration of water vapor is delivered over a sample placed inside the sample pan connected to the Surface Measurement Systems Ultrabalance™ measuring realtime mass changes caused by sorption or desorption of water molecules. Prior to sorption measurements, the sample can be in-situ preheated/dried at temperatures of up to 300oC.
-
product
Media Meter Software Tool
Dolby Media Meter is an innovative software tool that accurately measures loudness the way your viewers experience it in programming for broadcast, packaged media, cinema trailers, video on demand (VOD), and games. Differences in audio levels between programs and channels, or between programs and commercials, are a major annoyance to TV viewers. Although easy to hear, these differences are much more difficult to measure. And without accurate measurement, you can't regulate these irritating shifts in sound level.
-
product
Rectifier Transformers
Osborne’s Rectifier Transformers are used in conjunction with various rectification configurations to convert AC input to DC output(s). Key characteristics include regulation, transformer utilization and AC ripple. Osborne rectifier transformer designs are often engineered to operate in advanced rectifier circuit applications.
-
product
Industrial Computed Tomography
TomoScope® S
In both design and construction, the measuring machine meets the legal requirements for a fully protective device according to x-ray device regulations. Additional safety features have been included over and above the legal requirements.
-
product
Low Power Programmable AC Power Source With Transients
Chroma Systems Solutions, Inc.
Equipped with a host of powerful features: power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, waveshape synthesis and regulation test software
-
product
Motion Control
The ACE products in this segment enhance the quality of any type of movement. Anyone who wants to raise or lower loads, regulate the feed of an object to the precise millimeter or gently decelerate rotating or linear movements will find the right solution here.
-
product
Introduction to Graphical User Interface - Softpanel
61800 Series
The increased demand for Distributed Energy Resource (DR) products such as PV Inverter and Wind Energy systems, have increased the demand for regulation test standards to insure proper operation and safety of on-grid products. Manufacturers testing to prove compliance, need test equipment that can simulate and measure and test their products. Chroma’s 61800 family of Regenerative Grid Simulators provide a full 4 quadrant, regenerative, grid simulation for compliance, safety, and product verification testing
-
product
Temperature and Humidity Regulator
H3431-4
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
product
Isolation Amplifiers
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
product
Vibration Meters
Companies must comply with the Control of Vibration at Work Regulations 2005 – this requires them to minimise and monitor exposure to hand-arm vibration and make sure that it does not exceed set levels and cause Hand Arm Vibration Syndrome. The best way to do this is by using a hand-arm vibration meter.
-
product
AC Source
5310（0~500Vrms/1KVA）
Voltage output has totally six ranges，maximum up to 500V，convenient for 300V above the voltage regulation test
-
product
LC/MS/MS Method Package For Mycotoxins
Mycotoxins are highly toxic chemical byproducts from fungi commonly found in crops, and residual content in foods are regulated the world over. This method package provides simultaneous multi-component analysis conditions for mycotoxins subject to the regulations in Japan, the USA, the EU, and China.
-
product
EMC Actuator for Gas + Brake Pedal
PSE-GB
Pneumatically operated actuator for operation of accelerator and brake pedal in vehicles. External set-point of the pedal actuator position and brake pedal force via analog voltage to closed-loop pressure regulator in external valve box.
-
product
Backflow Test Kit Repair Calibration & Certification
Meeting Water Safety regulations and standards has become a primary concern for all industries. Most municipal and state regulators demand that Backflow Prevention Testing be carried out no less than once per year and that testing devices be calibrated and if required, certified regularly.
-
-
product
Regulated Transmitter
VIP 5000
The VIP series of Electrical transmitters are purposely designed for deep Induced Polarisation or Resistivity sounding investigations. The VIP 5000 internal microprocessor is capable of excellent current regulation in almost any load. Predominantly used as part of mineral exploration studies, the VIP series include three systems with different power specifications. This transmitter is generally used together with V-Fullwavers or Elrec Pro receivers.
-
product
Wall Mount Power Supplies
AC-DC Single Output
Although small in size, these mini-modules offer high performance at modest prices. All models, with series regulated outputs ranging from 1 to 75 volts and as high as 2.5 amps, may be mounted in an area only 3.5" x 2.5". Terminal strip input/output connections eliminate all need for sockets or soldering. Short circuit protection, encapsulated construction, and conservative design assure long term reliability.
-
product
Bench Power Supply, DC, Single, Adjustable, 1 Output, 1 V, 36 V, 0 A, 3 A
72-8345A
Switch Mode Laboratory DC Power Supplies Precision adjustable supply provides adjustable 1~36VDC output with adjustable current limiting from 0~3A. It is ideal for test, measurement and service applications where tight voltage and current regulation are critical. Highly efficient switch mode design delivers outstanding performance from an extremely compact footprint. Unique separate output ON/OFF control allows voltage and current setting, with the supply output turned off. Part of a Complete Series, this slim supply occupies little bench space while providing very high precision and 90W of continuous output.
-
product
Walk-In Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Energy-saving design: Adopting PID + PWM principle of VRF (refrigerant flow control) technology to achieve low-temperature energy-saving operation (electronic expansion valve according to thermal energy conditions refrigerant flow servo control technology) low temperature working state, the heater does not participate in the work, through PID + The PWM regulates the flow rate and flow direction of the refrigerant, and regulates the three-way flow of the refrigerant pipe, the cold bypass pipe, and the hot bypass pipe to achieve automatic constant temperature to the working chamber. This method can reduce energy consumption by 30% under low temperature conditions. The technology is based on Danish Danfoss' ETS series of electronic expansion valves, which can be used to smoothly adjust the cooling capacity for different cooling capacity requirements, that is, to achieve the compressor cooling capacity adjustment when different cooling rate requirements are met.
-
product
SparkFun Breadboard Power Supply Stick
3.3V/1.8V
This is a very simple board that takes a 4-9V input voltage and outputs a selectable 1.8V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.
-
product
Current Calibrators
Used for basic measurements, tests and regulation techniques for setting and verifying test installations and instrumentation.
-
product
Technology of Global Market Leader
AeroFIS
Aerodata is the only manufacturer of Flight Inspection Systems with an in-house aircraft integration capability and can therefore assume full responsibility for the integrated performance of the aircraft and flight inspection equipment. As a European manufacturer with international recognition, we can provide unique capabilities for the supply of advanced flight calibration equipment with special consideration of compliance with both European (EASA) and US (FAA) regulations, equipment compatibility with neighboring countries, and highest levels of product support.
-
product
Fixed Probe Temperature / RH
S.TO1 / S.TO2
Fixed horizontal interchangeable temperature and humidity probes with SICRAM 2 module for active transmitters, humidity and temperature regulators series HD2717T and HD2817T.
