-
product
PXI Precision Resistor Module 9-Channel, 2 to 52.4k
40-297-033
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
NI-9229, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module
779785-01
±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module - The NI‑9229 performs differential analog input. The NI‑9229 is an effective general-purpose analog module because of its resolution, sample rate, and input range. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating.
-
product
Multiplexed Measurement Unit
YAV90MMU
YAV90MMU module (Multiplexed Measurement Unit) is a powerful subsystem containing 16-channel multiplexer and a 600V data acquisition channel with capability to control external switching and it is expandable through CAN bus.
-
product
PXI Prototyping Module, 1-Slot, 9-Pin D-Type
40-225A-701
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
Single Board Computer
VPX6-185
Curtiss-Wright Defense Solutions
The VPX6-185 NXP Single Board Computer (SBC) provides functionality to the Curtiss-Wright VPX family that includes quad-processor DSP, FPGA accelerator and XMC/PMC carrier modules. The VPX6-185 6U VPX SBC is based on the 8640/8641 processor. Available in single-core and dual-core versions with AltiVec and up to 2 GB of DDR2 SRAM, the VPX6-185 Power Architecture SBC provides high performance VPX processing and a long list of features and I/O interfaces to satisfy the most demanding requirements of embedded computing.
-
product
cRIO Modules
The cRIO technology (RIO = reconfigurable I / O) from National Instruments enables the creation of customized measurement and control hardware circuits based on FPGA chips using the NI LabVIEW graphic development tool. The cRIO core comprises an FPGA chip and surrounding circuits that allow LabVIEW to perform a hardware synthesis.
-
product
Keysight Switch/Load Unit (SLU)
E6198B
The Keysight Switch/Load Unit (SLU) utilizes a standard VERSA Module Eurocard (VME) type enclosure to bring you the best-in-class switching solution for mechatronic type testing.
-
product
SMARC Short Size Module With Qualcomm® QRB5165 Series Octa-Core SoC
LEC-RB5N
- Qualcomm® Kryo™ 585 CPU (8x Arm Cortex-A77 cores)- Qualcomm® Hexagon™ Tensor Accelerator (HTA) running up to 15 TOPS- 4K HDMI/MIPI DSI display, MIPI CSI cameras- 2x PCIe x2 Gen3- 2x GbE Ethernet- 2x USB 3.1/2.0 and 4x USB 2.0- GPIO/SD and UFS- 5VDC +/-5% voltage input
-
product
PXI/PXIe LVDT/RVDT Simulator Module, 2-Banks
43-670-103-AABBCC
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal.
-
product
PXI-2595, 5 GHz, 50 Ω, 4x1 PXI RF Multiplexer Switch Module
778572-95
5 GHz, 50 Ω, 4x1 PXI RF Multiplexer Switch Module—The PXI‑2595 is ideal for applications that require the routing of high-frequency signals inside automated test equipment (ATE) systems because it can switch signals with very low insertion loss. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
Circuit Simulation, Power Analysis and Jitter Analysis Design Tools
GreenPoint®
The GreenPoint Design Simulation Tool is an interactive online design and verification tool to help you generate and validate an electronic design. The simulation module provides an interactive design and verification environment. The power analysis module provides an interactive environment to analyze the performance of intelligent power modules (IPMs). The Phase Noise Explorer module enables an interactive environment for advanced phase noise/jitter analysis of clock tree designs.
-
product
BlueView AUV Modules
Teledyne BlueView is recognized as the leading manufacturer of integrated Multibeam Profiling sonar systems for high resolution data collection. Our unique technology allows BlueView to offer some of the most technologically advanced, light-weight, low-power systems for AUV manufacturers and operators. Standard OEM modules are available through most AUV manufactures, and Engineered To Order (ETO) solutions are also available to accommodate non-standard AUV solutions. The Multebeam Profiler and SmartCore Data-logger combination provide real-time profiles and storage of data for post-mission review.
-
product
PXI Potentiometer Module 3x24 Bit, 0 Ohm to 16M Ohm
40-296-121-3/24
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
ITA, I2 Micro ICon, 168 Position, With Oversized Backshell
410130106
The i2 Micro iCon ITA with oversized cable clamp is capable of holding up to 168 QuadraPaddle contacts. With a wider 1.97” footprint, it is ideal for applications requiring shielded twisted pair wiring or other wire types with oversized jackets. The 30-degree u-shaped cable clamp allows ITA modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 1.80". The removable cover allows easy access to wiring for maintenance and probing. Integrated spring locking tabs ensure even and secure engagement.
-
product
16-Channel VME RTD/Resistance Input Module
V410
The V410 is a 6U VME module that provides sixteen independent analog inputs that may be used to read RTDs, thermistors, and other similar resistive sensors. It can also read cryogenic diodes. Users may set input range and adjust other settings at VMEbus speed, and depending on the range selected the microprocessor will do the necessary calculations and output voltage, resistance, or temperature. Temperature conversion is available for 100Ω and 1000Ω, series 385 and 392, platinum RTDs.
-
product
NI-9205, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
779357-01
±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The NI‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the NI‑9205 includes up to 60 V of overvoltage protection between input channels and common. In addition, the NI‑9205 also includes a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection.
-
product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
43-752A-112
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Optical Spectrum Analyzer Module Specification
CA92001B
UCINSTRUMENTS CA92001B C band optical spectrum analyzer module is a spectral engine for Process Analytical Technology applications. The OSA module acts as a stand-alone spectral engine, imaging and measuring a wide range of vapors, liquids and solids through transmission and diffuse reflection in a rapid non-destructive process. Leveraging our proprietary Micro-Optic technology, UC INSTRUMENTS’ C band OSA module features the following characteristics: (1) compact; (2) light-weight; (3) low power...show more -
product
PXI 2 Slot BRIC 30x16 2-pole (2 sub-cards)
40-561A-222-30X16
The 40-561A-222-30x16 is part of a range of high-density PXI BRIC matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays.
-
product
Switch Matrices
Becker Nachrichtentechnik GmbH
The three variants of the 4X4 matrix switch (RSWM-4X4, RSWM-4X4E, BSWM-4X4) are also available as Slot-In modules compatible to our 'Modular RF Systems' construction kit. Thereby the customer is able to combine different products in a space saving and efficient way for any application.
-
product
Specialized Extender Card Testing IP Modules
IP-Debug-Bus
IP-Debug-Bus is a specialized extender card which is optimized for testing IP Modules. The bus signals are all accessible via test points. The testpoints include multiple ground locations and .025 sq. posts for ease of connection to your logic analyzer or scope. The testpoints are labeled for easy identification
-
product
PXI/PXIe Microwave Relay, Quad SPDT, 18GHz, 50Ω, SMA
40-780B-524
The 40-780B-524 (PXI) and 42-780B-524 (PXIe) are quad SPDT 18GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
Single Channel SFP+ All-In-One Sensitivity Tester
SFP+ Tester
All in one mainframe to perform a complete sensitivity test on a single channel fiber optic transceiver. Includes Clock source, BERT and all optical modules
-
product
Standard VXI Module Shield Kits With Address Switch Opening
* Single-slot kit fits all VXI-1 Revision 1.0 to Revision 3.0 chassis.* Clamshell design fits C-size modules with 96-pin connectors.* Side shields include connector shrouds for maximum shielding.* RFI limiting, air vent slots along top and bottom edges for good air circulation thru the module.* Extruded front panel is bend resistant.* Address switch opening on component side shield.* Complimentary layout support includes PCB design template and CAD layout files.
-
product
Chassis - up to Sixteen 8x1 Modules, Thirty Two 4x1 Modules or Any Combination or Configuration of 8x1's, 4x1's, 2x1's and 2x2 Modules
CXAR/128-MF
These Chassis controls up to sixteen 8x1 modules, thirty two 4x1 modules or any combination or configuration of 8x1's, 4x1's, 2x1's and 2x2 modules. LEDs on the front panel show switch and power status. Add Switch Modules, CP8 Driver Modules and a Control Module to complete the system. Keypad Manual manual control with LCD display is optional.
-
product
Fibre Channel XMC Interface Module
XMC-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
PXI/PXIe 15W Programmable Resistor Module
42-254-014
The 40-254-014 (PXI) and 42-254-014 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
PXI/PXIe 15W Programmable Resistor Module
40-254-010
The 40-254-010 (PXI) and 42-254-010 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 31Ω with 0.125Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
PXI/PXIe High Density Precision Resistor Module, 3-Channel, 2.5 Ω to 201 kΩ
40-297A-141
The 40-297A-141 (PXI) and the 42-297A-141 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 201 kΩ, 0.25 Ω Resolution. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
37-Pin D-Type Male Right Angled PCB HV
40-963-037-RM-HV
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
