Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
Coax Contacts
-
VPC’s coax contacts are a family of blind‑mate RF contacts covering 50 and 75 Ohm applications from low MHz up to 50 GHz, designed for high durability (typically 10,000–20,000+ mating cycles) in modular test interfaces.
-
Product
Shock Absorber Tester
-
Maschinenbau Haldenwang GmbH & Co. KG.
Display on LON analog displays with theEvaluation in "Lehr''s damping factor" or damping ratio "D"Fully automatic testAutomatic test start after bilateral plate load of more than 60kgFrequency controlled drive excitation by electric motors to determine the maximum vibration amplitude with subsequent evaluation of the axle dampingrunning underbody as self-supporting frame constructionParallelogram guided test plates, thus no fixed wheel contact requiredgalvanized version
-
Product
Connector Specifications
Board to Board Connector Specifications
-
With Springprobe™ technology, extremely high node count requirements can be satisfied without extreme force. Our system can be designed to work with LESS THAN 5 GRAMS OF FORCE per node to maintain electrical connectivity. And with contact heights as low as .032”, stack ups can be reduced without sacrificing signal integrity. If you have a tough Board to Board Connector requirement, contact us to see if RC Springprobe™ technology is right for your project.
-
Product
Replacement Protective Cover, I1, Receiver
310113524
-
The receiver protective cover is designed to protect your modules and contacts while the test system is not in use. A protective cover is included with the i1 Receiver.
-
Product
NON CONDUCT DIGITAL THERMOMETER
IBL-MT9
-
International Biological Laboratories
This Digital Non Contact type Infra Red Thermometer with laser sensor uses temperature sensor of Thermopile 8 - 14 mm and measures temperature from -50 to 1000 Degree C and also in Fahrenheit scale.
-
Product
Laser Source
-
Is an Amplified Spontaneous Emission (ASE) based broadband light source, designed for general laboratory applications. It is a reliable and cost-effective unit that can be ordered with multi channel options. The LD operating temperature and drive current are precisely monitored by a micro-controller to ensure constant output power and emission wavelength stability. With compact size configuration, it’s also suitable for OEM integration, User can control the ASE source output power level by adjusting the drive current along with remote status monitoring, contact Optilab for more information.
-
Product
Diaphragm Operated Pressure Switch
1000W
-
Extremely rugged construction provides excellent reliability in chemical, petroleum and industrial plants. Bellville spring movement permits mounting of control in any position and helps prevent contact chatter. new design also provides high overpressure protection. Available with standard weatherproof housing to meet NEMA-1 through 4X and NEMA-13, JIC.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
610138100
-
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
-
Product
High density PCB connectors
MHD/MDD/MDP Series
-
Smiths Interconnect's MHD/MDD/MDP series is an ESA qualified, high density board to board and board to wire interconnect available in up to 400 positions, with available insulators to accommodate coax and power contacts.
-
Product
ICE 3000 Series
ICE3005
-
The ICE3005 is an agile filter/amplifier cascade for the UHF frequency band with a VHF bypass. It enables simultaneous operation of multiple transceivers in a cosite environment and is factory configured for an ARC-210 interface. This filter/amplifier provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals while still providing full output power in transmit mode and excellent selectivity to interfering signals at the transceiver’s RF input in receive mode. All transmit, receive, and bypass switching is incorporated into the two-port design. The ICE3005 also includes a separate audio processor circuit that mitigates popping and drop-outs in the R/T audio that are common in hopping or blanked waveforms. The ICE3005 incorporates extensive Built-in-Test capability and is qualified for military applications. A mounting tray is available for easy incorporation on your platform. Cost-effective modifications are available on the ICE3005. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
Product
Adhesion Tester
Surf-2
-
Rtec Adhesion Tester is a turn key solution to measure Pull up Adhesion force, Work of Adhesion and Shear Adhesion of materials. Equipped with Ultra-Sensitive Capacitance Load Cells this tester provides µN level resolution with forces up to 5N. The High-Resolution sensors allow characterization of large samples over macroscopic length scales to study the effect of texture and other surface modifications. Integrated with High Resolution Inverted Camera, it allows the researchers to measure Contact Area vs. Force making it extremely useful in measuring Adhesion of Soft Materials, Biomimetics and Hydrogels.
-
Product
Signal / Mini Coax, Module, ITA, TriPaddle, 90 Series, 16/16 Position
510108210
-
This module can accommodate certain VPC mini pneumatic contacts, but cannot be fully populated in all 16 positions with them. See specific product drawings for applicable limitations. For further assistance please contact a Field Application Engineer. Primary mating module 510104243.
-
Product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Round Post
610138115
-
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.
-
Product
Contact Ultrasound Sensors
-
Inspect bearings, steam traps and perform other mechanical inspections with our Needle or Threaded contact sensors.
-
Product
CGS Inline-Test-Station
-
Computer Gesteuerte Systeme GmbH
Test-specific contacting elements (upper and lower cassettes) which are inserted into the insertion device of the test headClamping device per cassette for fastening (pneumatic clamping set)
-
Product
LXI Low Thermal EMF Matrix 1-pole 44x33
60-510-021
-
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
Product
Single 32x2 1-Pole High-Density PXI Matrix Module
40-520-502
-
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI Source Switching Module
40-618-001
-
The 40-618 PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module. Typical applications include signal routing for avionics test systems that conform to the ARINC 608A specification.
-
Product
Tool, Solder Kit, Mini Coax with Solder Sleeve
910121144
-
Used to solder Mini Coax Solder Sleeve contacts.
-
Product
S-100 Bus, Vectorbord Plugbord
8804
-
VECTOR Electronics and Technology, Inc.
100 Gold plated edge contacts (50 each side)on 0.125"(3.175mm) centers. Voltage/Ground buses. Zig-Zag buses. I/O mounting area for ribbon cable header. Row and column legends provided. S-100 Form Factor.Pin 1 and 51 committed to power. Pin 50 and 100 committed to ground.
-
Product
Intermittent Break Analyzer
JW3324
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3324 Intermittent break analyzer is used to monitor the intermittent disconnection of interconnection devices in dynamic environment such as vibration. It can detect the contact reliability under vibration and display the time and times of disconnection.Connectors and cables are widely used in aviation, aerospace systems and military equipment. Therefore, JW3324 Intermittent break analyzer is a basic testing instrument used by manufacturers, research institutions and operators for manufacture-testing, research -developing, engineering construction and maintenance.
-
Product
Plugbord
3682-4
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. Interleaved buses pattern on wiring side, solder coated for user convenience. Overall ground plane with clearance around each hole on component side. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board. Row and column legends provided.
-
Product
PXI Single 8 Channel Switch Simulator
40-485-021
-
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
STD Bus, Vectorbord Plugbord
4610
-
VECTOR Electronics and Technology, Inc.
56 Gold plated edge contacts (28 each side)on 0.125"(3.175mm) centers. 3-Hole solder pads (0.28” x 0.080”) and buses forinterconnecting multiple component leads. Row and column legends provided.
-
Product
Power Loggers/Energy Loggers
-
Designed for 50/60 Hz commercial line use 3 circuits (1P2W), single circuit (1P3W, 3P3W, 3P4W) Save data to the SD card continuously (Current) Clamp input (Voltage) Non-metallic contact sensor
-
Product
Portable Digital Manometer
PS309
-
Featured are an integral variable reluctance transducer, solid state electronics module, 3 digit liquid crystal display (LCD)* and battery pack with six 1.5V penlight cells for truly portable operation. The units can also be powered from an external DC power supply or AC battery eliminator (converter) module. The transducer features all corrosion resistant materials in contact with the pressure media (both ports in differential units), very low internal cavity volumes and ultra-low volumetric displacement with full-scale pressure excursion. Transducer calibration is unaffected by dielectric properties of the sensed fluid. Gauge and differential transducers may be disassembled and range changed by simple diaphragm replacement.
-
Product
VTAC, Insert, Receiver/ITA, SIM, Pass-Thru, 8 Pos, 1 Slot
610151103
-
VTAC, Insert, Receiver/ITA, SIM, Pass-Thru, 8 Pos, 1 Slot VTAC inserts are reversible and can be used as a Receiver or ITA insert.VPC's revolutionary high speed VTAC insert contains 8 gold-plated, self-aligning contacts and is designed to reduce crosstalk. With a data transfer rate of more than 12.5 Gbps per differential pair and a cycle life of over 150,000, VTAC has set the standard for high speed interconnect solution requirements. Sold in individual quantities.Use with VPC's right angle VTAC insert (p/n 610151104) or VPC's vertical header (p/n 610151107) to connect directly to a PCB.
-
Product
Selector Switches
-
Elma offers a wide range of dimensions, number of switching positions and contact arrangements. Our selector switches continue to be the foundation of Elma's longstanding reputation for quality, feel and reliability.
-
Product
PXI High Density Matrix Module, 128x2, 1-Pole, 2A, 60W
40-584A-001
-
Our model 40-584A, along with the following models 40-585A, 40-586B and 40-587A are high-density single pole PXI matrices each supporting 256 crosspoints. All models use gold-plated contact electromechanical relays. This module is also available in PXIe format (42-584A-001).
-
Product
Environmental Test Probe, Temperature
72-8366
-
Simple thermocouple junction at the end of a 1m wire provides effective low cost ambient temperature measurement. It is suitable for measuring air temperature and may be placed in direct contact with hard surfaces. Type K thermocouple temperature probes are commonly used with all types of industrial temperature controls and measurement equipment, and are compatible with Tenma handheld thermometers and digital multimeters that include temperature function. All are terminated with standard Type K plugs.
