Corrosion
gradual degradation of a material over time
See Also: Salt Spray, Salt, Salt Fog, Corrosion Test
-
Product
Corrosion Test
-
The purpose of this test is to determine the resistance of materials and protective coatings to corrosive atmospheres when a more corrosive environment than the salt fog/spray test is required. The test is used when material is stored or operated in areas, for example, where acidic atmospheres exist, such as in industrial areas or near the exhausts of any fuel-burning device. Gases such as sulfur dioxide are used to replicate the exhausts of fuel burning devices.
-
Product
Corrosion Test Chamber
CME SF-CCT
-
CME SF-CCT chambers are designed to be flexible enough to comply with as many different CCT specifications as possible. These may be programmed to conduct a whole range of corrosion tests such as wet cycle, dry cycle, controlled humidity as well as the salt spray test in a single chamber. This can occur in any sequence and be repeated automatically. A wide range of optional accessories enable additional climates to be added to further extend the number of climates and conditions that can be created.
-
Product
Corrosion Mitigation Instrumentation
AG-1
-
1/4 turn locking deviceEasily located with "Detectron" 7-t valve box11 terminal board (AG-3 with N,S,E,W indicators)AG-1 with 1 piece bell shape insert, keeps terminal board dry, even when submerged.
-
Product
Pipeline Integrity and Corrosion Control
-
The integrity of buried pipelines is of paramount importance for safety, environmental and cost reasons.
-
Product
Salt Spray Testing/Cabinet Based Corrosion Testing
-
Sometimes referred to salt mist, salt fog, humidity or corrosion testingAll corrosion and environmental related tests can be tailored to customer requirementsTypical exposure times range from 16 hours to over 1000 hoursAccelerated corrosion testing can be used to check protective coatings, surface finishes and material compatibilitiesOur facilities provide a continuous controlled corrosive exposure and can combine salt spray and humidity environments.
-
-
Product
Salt Spray Corrosion Test Chamber
-
Xi'an LIB Environmental Simulation Industry
Used to simulate harsh, corrosive environments by exposing materials to salt fog.
-
Product
BCX Basic Cyclic Corrosion Cabinet
-
Atlas Material Testing Solutions
Basic cyclic tests are used to qualify a coating or material for a specific end use on a pass-fail basis, or determine the probability of corrosion of a specific material.
-
Product
Concrete Corrosion Testing
-
This category comprises the range of instruments that evaluate parameters related to the corrosion of the concrete or the steel reinforcing bar within the concrete.
-
Product
Corrosion Inhibitor Evaluation
ASTM G202
-
Metals Samples provides solutions to study the performance of corrosion inhibitors in the laboratory. The Rotating Cage is helpful in selecting corrosion inhibitors for use in oil and gas production pipelines and facilities, transmission pipelines, as well as in oil refineries. It simulates aggressive field flow conditions that cause localized pitting corrosion in a simple laboratory setup. The precision, i.e., repeatability and reproducibility, of the rotating cage has been established (ASTM G202).
-
Product
Cyclic Corrosion Test Chambers
CCT
-
Cyclic Corrosion Test Chambers are used throughout the automotive, aerospace, fasteners, electronics, paints and coating industries.
-
Product
Continuous LPR Corrosion Meter
MS2001L
-
The MS2001L is a microprocessor-based, field-mountable corrosion rate meter. This versatile instrument measures the instantaneous corrosion rate and electrochemical current between the electrodes of any standard 2-electrode linear polarization resistance (LPR) probe. Corrosion rate is displayed on the LCD display.
-
Product
Cyclic Corrosion Testing Chambers
-
Weice Testing Instrument Co.,Ltd.
Any combination of different environments may be programmed to occur sequentially in any order, to form a corrosion cycle which will then be performed automatically or repeated a pre-set number of times. Each environment can also be selected individually.
-
Product
SF Walk-In Series Corrosion Cabinet
-
Atlas Material Testing Solutions
The SF Walk-In Series are rugged and reliable traditional salt fog (spray) and humidity cabinets. In addition, they can perform basic wet/dry cyclic and condensing humidity tests when properly configured. Custom sizes and dimensions are available.
-
Product
Corrosion Test Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Corrosion test chambers for salt spray testing is used throughout the automotive, aerospace, fasteners, electronics, paints and coating industries!
-
Product
Phased Array Corrosion Mapping Software
Concerto
-
Concerto is a UT acquisition and analysis software specially designed for Phased Array corrosion mapping. For the tough field conditions that operators deal with Concerto features no menu, less than 18 icons, and few controls so that operators can easily work and not be bothered by complex GUIs. Concerto is simple and easy to work with yet WT, Surface, and back wall C-scan can still be analyzed and setting can be changed using the same acquired data.
-
Product
Corrosion & Temperature Control
-
Corrosion & Temperature Control accessories including corrosion resistant materials, high temperature packages, temperature control jacket, cylinder insulating cover, and more
-
Product
Advanced Rebar Corrosion Rate Determination System
Gecor 8
-
James Instruments Gecor 8 represents the latest technology in steel reinforcing bar corrosion rate determination. It combines state of the art embedded microprocessor systems and computerized flash technology with the world's leading research in reinforcing bar corrosion rate analysis.
-
Product
Pulse Holiday Detector
NOVOTEST SPARK-1
-
Pulse Holiday Detector NOVOTEST SPARK-1 designed to detect pits, flaws, and holes in different non-metallic insulation coatings (such as polymers, epoxy, bitumen, etc.) and is mostly used for oil and gas metal pipelines and other objects. The device can be used while the pipeline construction, operation or service. Tested coating thickness is up to 12 mm. Such tests are needed to evaluate the oil and gas pipelines corrosion protection reliability.
-
Product
CORROSION GAUGE
MX-3
-
With the hand held MX-3 Ultrasonic micrometer, you can make reliable measurements or scan a length of material for the thinnest point. The tool's backlit display is easy to read, even in dim light, and the unit operates for up to 200 hours on a single set of batteries. The MX-3 comes complete, ready to use and is protected by Dakota Ultrasonics 5 year limited warranty.
-
Product
Syringe Pump
65x
-
The 65x syringe pump provides precise, predictable flow and pressure control at flow rates from sub-microliter to 25 mL/min. Exceptional low-flow stability at up to 20,000 psi (1,390 bar) makes this the ideal pump for high pressure applications from deep well core analysis and polymer extrusions. The 65x pumps to the lowest flow rates with zero pulsation available on the market!The SyriXus controller has backlighted keypad and 4-line LCD display, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly. Control the pump remotely using driver for LabVIEW™ software, in addition to pump controller. The 65x pump module has a single-ratio drive train with autolubricating gears for long life and low maintenance. Special fittings are used to prevent leaks and ensure safety at maximum pressure. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases. Continuous pumping is available in either single or dual pumping system controlled via air valves, offering zero pulsation for unlimited delivery. Trust in the Teledyne LABS SyriXus pumps for proven reliable design. Known for years of performance, it can delivery fluid or pressurized gas for long term experiments. Or hold pressure constant in the system at a simple click of the button.
-
Product
Isolation Tester UIP
-
The devices of the UIP (Union Isolations Prüfer) isolation tester series are used to test the pore-free condition of corrosion protection coatings of pipes, vessels or plant system parts. The battery-powered device generates test voltages between 5 kV and 30 kV, which are applied to the grounded test object via test electrodes. The location of a defect is signalized by a spark-over with an additional audible warning.
-
Product
SF6 Gas Analysis Systems
-
Weshine Electric Manufacturing Co., Ltd
Discharges during switching operations in SF6 gas-filled plant lead, over time, to increased concentrations of toxic and highly corrosive decomposition products. The use of gas analysis instruments is absolutely necessary to monitor the concentration of harmful decomposition products, thus ensuring long-term plant safety.
-
Product
Pressure Cooling Elements
-
Rugged cooling elements with corrosion resistance that allow your pressure measurement devices to operate accurately at high pressure and temperature conditions.
-
Product
CORROSION GAUGE
MVX
-
The MVX finishes the line of MX gauges with class. This thing is loaded with all of the features of the MX gauges and a lot more. Four selectable display options: RF, Rectified, B-Scan, and Large Digits. An internal data logger that stores a total of 12,000 readings and waveforms, 64 user custom definable setups, selectable transducer table for improved linearity, thru paint mode with the single press of a button, multiple calibration and material selection options, and auto waveform find just to mention a few! Equipped with a single element flaw prove-up mode for basic angle beam inspections. This is all nicely packaged in a very mini portable aluminum extrusion for extra durability and portability! The MVXview java-based PC software makes this thing a complete kit, and then some!
-
Product
AD06A Baratron® Differential Pressure Sensor
-
AD06A Baratron® differential pressure sensors are single-ended dual-electrode/AC bridge devices that are extremely stable and designed to minimize the effect of temperature changes. Full Scale ranges are available from 25,000 Torr down to 0.1 Torr. Each range measures down to 1 part in 106 Full Scale with selected percent Reading accuracy limited by this resolution and with accuracies ranging from 0.25% to 0.05% of Reading. They are constructed of Inconel® and stainless steel, allowing use with many wet, dirty, or corrosive gases.
-
Product
Electrical Resistance (ER) Monitoring
-
The electrical resistance (ER) technique is an "on-line" method of monitoring the rate of corrosion and the extent of total metal loss for any metallic equipment or structure. The ER technique measures the effects of both the electrochemical and the mechanical components of corrosion such as erosion or cavitation. It is the only on-line, instrumented technique applicable to virtually all types of corrosive environments.
-
Product
Moisture Resistance/ Humidity Test
-
This test is performed for evaluating the resistance of component parts and constituent materials to the deteriorative effects of the high-humidity and heat conditions typical of tropical environments. Most tropical degradation results directly or indirectly from absorption of moisture vapor, and from surface wetting. These phenomena produce many types of deterioration, including corrosion of metals; physical distortion and decomposition of organic materials; leaching out of constituent components of materials, and detrimental changes in electrical properties.
-
Product
(25kN) Fatigue Testing Systems
8872
-
The 8872 fatigue testing system is ideal for fatigue and static testing of biomedical, advanced materials, and manufactured components. The servohydraulic actuator is conveniently located in the crosshead for easy table mounting. The T-slot base makes it easy to secure orthopaedic specimens, automotive components, and manufacturing assemblies. The adjustable crosshead, actuator-mounted load cell, and corrosion resistant T-slot base with unique drain channel are essential for testing biomedical specimens immersed in a saline bath.
-
Product
Potentiostat Galvanostat
VersaSTAT 4
-
The improved low current performance with fA resolution and pA accuracy addresses current sensitive applications such as sensors, corrosion, inhibitors, and combined with the optional FRA, coating technologies. The additional analog filtering makes the VersaSTAT 4 an even better choice for low-current applications while the additional bandwidth filtering adds extra stability for capacitive cells. The VersaSTAT 4, with its additional capabilities, makes an exciting addition to our VersaSTAT family making them even more of an exceptional value for all of your application needs.
